Messages in this thread | | | From | Bjorn Helgaas <> | Subject | Re: [PATCH] x86, HPET: mark HPET PCI BARs as IORESOURCE_PCI_FIXED | Date | Fri, 24 Sep 2010 17:06:10 -0600 |
| |
Sorry Yinghai, I forgot to copy you on the initial post. Any comments on this? If not, we should try to get it into linux-next soon.
On Thursday, September 23, 2010 05:30:47 pm Bjorn Helgaas wrote: > > We often discover the HPET early, via the static ACPI HPET table, before > enumerating PCI devices. If the HPET is implemented as a PCI function, > we will discover it again during PCI device enumeration. We must make > sure we never move the PCI function out from under the driver. > > Doing this for *any* PCI BAR that matches a previously discovered HPET > should be more generic than the previous ATI-specific quirk. > > This is for a regression from 2.6.34, but the reporter has been unable > to test it yet. > > Reference: https://bugzilla.kernel.org/show_bug.cgi?id=18482 > Reported-by: Simon Arlott <simon@fire.lp0.eu> > Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> > --- > > arch/x86/kernel/quirks.c | 19 +++++++++++++++++++ > arch/x86/pci/fixup.c | 28 ---------------------------- > 2 files changed, 19 insertions(+), 28 deletions(-) > > > diff --git a/arch/x86/kernel/quirks.c b/arch/x86/kernel/quirks.c > index 939b9e9..8acd667 100644 > --- a/arch/x86/kernel/quirks.c > +++ b/arch/x86/kernel/quirks.c > @@ -507,6 +507,25 @@ static void force_disable_hpet_msi(struct pci_dev *unused) > DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS, > force_disable_hpet_msi); > > +static void mark_pci_hpet_fixed(struct pci_dev *dev) > +{ > + int i; > + > + if (!hpet_address) > + return; > + > + for (i = 0; i < 6; i++) { > + struct resource *res = &dev->resource[i]; > + > + if (resource_type(res) == IORESOURCE_MEM && > + res->start == hpet_address) { > + dev_info(&dev->dev, "BAR %d: %pR is an HPET we found earlier; making it immovable\n", > + i, res); > + res->flags |= IORESOURCE_PCI_FIXED; > + } > + } > +} > +DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, mark_pci_hpet_fixed); > #endif > > #if defined(CONFIG_PCI) && defined(CONFIG_NUMA) > diff --git a/arch/x86/pci/fixup.c b/arch/x86/pci/fixup.c > index 6dd8955..08eba69 100644 > --- a/arch/x86/pci/fixup.c > +++ b/arch/x86/pci/fixup.c > @@ -493,31 +493,3 @@ static void __devinit pci_siemens_interrupt_controller(struct pci_dev *dev) > } > DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SIEMENS, 0x0015, > pci_siemens_interrupt_controller); > - > -/* > - * SB600: Disable BAR1 on device 14.0 to avoid HPET resources from > - * confusing the PCI engine: > - */ > -static void sb600_disable_hpet_bar(struct pci_dev *dev) > -{ > - u8 val; > - > - /* > - * The SB600 and SB700 both share the same device > - * ID, but the PM register 0x55 does something different > - * for the SB700, so make sure we are dealing with the > - * SB600 before touching the bit: > - */ > - > - pci_read_config_byte(dev, 0x08, &val); > - > - if (val < 0x2F) { > - outb(0x55, 0xCD6); > - val = inb(0xCD7); > - > - /* Set bit 7 in PM register 0x55 */ > - outb(0x55, 0xCD6); > - outb(val | 0x80, 0xCD7); > - } > -} > -DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ATI, 0x4385, sb600_disable_hpet_bar); > >
| |