lkml.org 
[lkml]   [2010]   [Aug]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH] CRIS RS485: Check SER_RS485_RTS_BEFORE_SEND before delaying.
Hi Jesper,

the following patch fixes the usage of the delay in RS485 mode
on the Cris architecture.

Very recently, the RS485 interface has been fixed by adding two further
fields (see commit 1b6331848b69d1ed165a6bdc75c4046d68767563).

This patch checks the value of the flag SER_RS485_RTS_BEFORE_SEND before
delaying.

Best regards,

Claudio


CRIS RS485: Check SER_RS485_RTS_BEFORE_SEND before delaying.

Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
---
drivers/serial/crisv10.c | 21 ++++++++++++++-------
1 files changed, 14 insertions(+), 7 deletions(-)

diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c
index c856905..a2237e7 100644
--- a/drivers/serial/crisv10.c
+++ b/drivers/serial/crisv10.c
@@ -1411,11 +1411,12 @@ e100_enable_rs485(struct tty_struct *tty, struct serial_rs485 *r)
CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 1);
#endif

- info->rs485.flags = r->flags;
- if (r->delay_rts_before_send >= 1000)
+ info->rs485 = *r;
+
+ /* Maximum delay before RTS equal to 1000 */
+ if (info->rs485.delay_rts_before_send >= 1000)
info->rs485.delay_rts_before_send = 1000;
- else
- info->rs485.delay_rts_before_send = r->delay_rts_before_send;
+
/* printk("rts: on send = %i, after = %i, enabled = %i",
info->rs485.rts_on_send,
info->rs485.rts_after_sent,
@@ -3234,9 +3235,9 @@ rs_write(struct tty_struct *tty,
e100_disable_rx(info);
e100_enable_rx_irq(info);
#endif
-
- if (info->rs485.delay_rts_before_send > 0)
- msleep(info->rs485.delay_rts_before_send);
+ if ((info->rs485.flags & SER_RS485_RTS_BEFORE_SEND) &&
+ (info->rs485.delay_rts_before_send > 0))
+ msleep(info->rs485.delay_rts_before_send);
}
#endif /* CONFIG_ETRAX_RS485 */

@@ -3694,6 +3695,11 @@ rs_ioctl(struct tty_struct *tty, struct file * file,

rs485data.delay_rts_before_send = rs485ctrl.delay_rts_before_send;
rs485data.flags = 0;
+ if (rs485data.delay_rts_before_send != 0)
+ rs485data.flags |= SER_RS485_RTS_BEFORE_SEND;
+ else
+ rs485data.flags &= ~(SER_RS485_RTS_BEFORE_SEND);
+
if (rs485ctrl.enabled)
rs485data.flags |= SER_RS485_ENABLED;
else
@@ -4527,6 +4533,7 @@ static int __init rs_init(void)
/* Set sane defaults */
info->rs485.flags &= ~(SER_RS485_RTS_ON_SEND);
info->rs485.flags |= SER_RS485_RTS_AFTER_SEND;
+ info->rs485.flags &= ~(SER_RS485_RTS_BEFORE_SEND);
info->rs485.delay_rts_before_send = 0;
info->rs485.flags &= ~(SER_RS485_ENABLED);
#endif
--
1.6.0.4


\
 
 \ /
  Last update: 2010-08-11 17:11    [W:0.046 / U:0.328 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site