lkml.org 
[lkml]   [2010]   [May]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] ad7877: fix spi word size to 16 bit
On Sun, May 16, 2010 at 15:25:34 -0400, Mike Frysinger wrote:
> On Sat, May 15, 2010 at 14:15, Oskar Schirmer wrote:
> > On Thu, May 13, 2010 at 00:53:35 -0700, Dmitry Torokhov wrote:
> >> On Fri, May 07, 2010 at 02:23:07PM -0400, Mike Frysinger wrote:
> >> > On Fri, May 7, 2010 at 05:41, Daniel Glöckner wrote:
> >> > > On 05/06/2010 08:26 PM, Mike Frysinger wrote:
> >> > >> i think it'd be a better idea to do something like:
> >> > >>   if (spi->bits_per_word != 16) {
> >> > >>     if (spi->bits_per_word) {
> >> > >>       dev_err(&spi->dev, "Invalid SPI settings; bits_per_word must be 16\n");
> >> > >>       return -EINVAL;
> >> > >>     }
> >> > >>     spi->bits_per_word = 16;
> >> > >>     spi_setup(spi);
> >> > >>   }
> >> > >
> >> > > There is no way to set bits_per_word using struct spi_board_info. The
> >> > > description of that structure in spi.h explicitly lists the wordsize as
> >> > > one of the parameters drivers should set themself in probe().
> >> > >
> >> > > Only struct bfin5xx_spi_chip allows to set this value in the board code.
> >> >
> >> > an obvious shortcoming in the SPI framework that should be fixed, but
> >> > that doesnt make any difference to the above code now does it ?  it'll
> >> > operate correctly regardless of the SPI bus master.
> >>
> >> So is the updated patch coming?
> >
> > The basic question I see is, whether it is in the
> > responsibility of ad7877 to check a wrong setting
> > possibly caused in board specific code. If so,
> > then the proposal by Mike should be used, but if not
> > so, it would introduce unneeded code.
> >
> > Remember: both versions end up in correctly setting
> > bits_per_word, with the difference merely in feedback
> > level.
>
> imo, unsupported board settings should always be detected & rejected.
> all SPI master drivers do this (detect & reject unsupported SPI slave
> settings).

please note, that bits_per_word is not a board setting,
it's a demand of the device. consequently, there is no one
to set unsupported values and thus none to be detected.

the only architecture setting bits_per_word thru spi_chip
is blackfin, but I cannot see a good reason, why the board
settings should engage with a fixed demand of the device?

Oskar
--
oskar schirmer, emlix gmbh, http://www.emlix.com
fon +49 551 30664-0, fax -11, bahnhofsallee 1b, 37081 göttingen, germany
sitz der gesellschaft: göttingen, amtsgericht göttingen hr b 3160
geschäftsführer: dr. uwe kracke, ust-idnr.: de 205 198 055

emlix - your embedded linux partner
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2010-05-17 09:31    [W:0.196 / U:0.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site