lkml.org 
[lkml]   [2010]   [Apr]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: Intermittent SATA failures ("link offline, clearing class 1 to NONE")
From
Hi,

Further to emails from November and December last year that Tejun Heo
was investigating:
http://markmail.org/message/l3g3s27rwj6iuhje#query:Intermittent%20SATA%20failures%20%22%28link%20offline%2C%20clearing%20class%201%20to%20NONE%29%22+page:1+mid:g6ujvdfz4om2rnvf+state:results

I'm having the exact same problem, see below excerpt from dmesg. Note
that the disk that fails is seemingly random:
ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.01: SATA link up <unknown> (SStatus 300 SControl 123)
ata2.00: link offline, clearing class 1 to NONE
ata1.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

I have attached a good and bad boot.

lspci -v shows:

00:1f.2 IDE interface: Intel Corporation Ibex Peak 4 port SATA IDE
Controller (rev 05) (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: Dell Device 02a4
        Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 20
        I/O ports at eca0 [size=8]
        I/O ports at ec90 [size=4]
        I/O ports at eca8 [size=8]
        I/O ports at ec94 [size=4]
        I/O ports at ecc0 [size=16]
        I/O ports at ecd0 [size=16]
        Capabilities: [70] Power Management version 3
        Capabilities: [b0] PCI Advanced Features
        Kernel driver in use: ata_piix
        Kernel modules: pata_acpi, ata_piix

00:1f.5 IDE interface: Intel Corporation Ibex Peak 2 port SATA IDE
Controller (rev 05) (prog-if 85 [Master SecO PriO])
        Subsystem: Dell Device 02a4
        Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 21
        I/O ports at ecb0 [size=8]
        I/O ports at ec98 [size=4]
        I/O ports at ecb8 [size=8]
        I/O ports at ec9c [size=4]
        I/O ports at ece0 [size=16]
        I/O ports at ecf0 [size=16]
        Capabilities: [70] Power Management version 3
        Capabilities: [b0] PCI Advanced Features
        Kernel driver in use: ata_piix
        Kernel modules: pata_acpi, ata_piix

I'm currently running linux-2.6.32-gentoo-r7 on amd64 but I've tried
linux-2.6.31-gentoo-r6 and linux-2.6.31-gentoo-r10 with the same
results. libata.force=nohrst makes no appreciable difference

As before 'echo "- - -" > /sys/class/scsi_host/hostX/scan' where X is
0 or 1 brings the drive back online.

As the original chat petered out I was hoping that this had since been
fixed. Anyone have any suggestions please?
2327040 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x24] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x25] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x26] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x27] disabled)
ACPI: LAPIC (acpi_id[0x09] lapic_id[0x28] disabled)
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x29] disabled)
ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x2a] disabled)
ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x2b] disabled)
ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x2c] disabled)
ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x2d] disabled)
ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x2e] disabled)
ACPI: LAPIC (acpi_id[0x10] lapic_id[0x2f] disabled)
ACPI: LAPIC (acpi_id[0x11] lapic_id[0x30] disabled)
ACPI: LAPIC (acpi_id[0x12] lapic_id[0x31] disabled)
ACPI: LAPIC (acpi_id[0x13] lapic_id[0x32] disabled)
ACPI: LAPIC (acpi_id[0x14] lapic_id[0x33] disabled)
ACPI: LAPIC (acpi_id[0x15] lapic_id[0x34] disabled)
ACPI: LAPIC (acpi_id[0x16] lapic_id[0x35] disabled)
ACPI: LAPIC (acpi_id[0x17] lapic_id[0x36] disabled)
ACPI: LAPIC (acpi_id[0x18] lapic_id[0x37] disabled)
ACPI: LAPIC (acpi_id[0x19] lapic_id[0x38] disabled)
ACPI: LAPIC (acpi_id[0x1a] lapic_id[0x39] disabled)
ACPI: LAPIC (acpi_id[0x1b] lapic_id[0x3a] disabled)
ACPI: LAPIC (acpi_id[0x1c] lapic_id[0x3b] disabled)
ACPI: LAPIC (acpi_id[0x1d] lapic_id[0x3c] disabled)
ACPI: LAPIC (acpi_id[0x1e] lapic_id[0x3d] disabled)
ACPI: LAPIC (acpi_id[0x1f] lapic_id[0x3e] disabled)
ACPI: LAPIC (acpi_id[0x20] lapic_id[0x3f] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a701 base: 0xfed00000
SMP: Allowing 32 CPUs, 28 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 0000000000100000
PM: Registered nosave memory: 00000000bf699000 - 00000000bf6af000
PM: Registered nosave memory: 00000000bf6af000 - 00000000bf6ce000
PM: Registered nosave memory: 00000000bf6ce000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000fe000000
PM: Registered nosave memory: 00000000fe000000 - 0000000100000000
Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:32 nr_node_ids:1
PERCPU: Embedded 24 pages/cpu @ffff880032e00000 s68632 r8192 d21480 u131072
pcpu-alloc: s68632 r8192 d21480 u131072 alloc=1*2097152
pcpu-alloc: [0] 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
pcpu-alloc: [0] 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 3096521
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/md3 libata.force=nohrst
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Initializing CPU#0
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
software IO TLB at phys 0x20000000 - 0x24000000
Memory: 12295696k/13631488k available (4401k kernel code, 1058592k absent, 276248k reserved, 1675k data, 420k init)
Hierarchical RCU implementation.
NR_IRQS:1280
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
HPET: 8 timers in total, 6 timers will be used for per-cpu timer
Fast TSC calibration using PIT
Detected 2394.877 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4789.75 BogoMIPS (lpj=23948770)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
mce: CPU supports 9 MCE banks
CPU0: Thermal monitoring enabled (TM1)
CPU 0 MCA banks CMCI:2 CMCI:3 CMCI:5 CMCI:6 CMCI:8
using mwait in idle threads.
ACPI: Core revision 20090903
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Xeon(R) CPU X3430 @ 2.40GHz stepping 05
Booting processor 1 APIC 0x2 ip 0x6000
Initializing CPU#1
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU1: Thermal monitoring enabled (TM1)
CPU 1 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
CPU1: Intel(R) Xeon(R) CPU X3430 @ 2.40GHz stepping 05
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Booting processor 2 APIC 0x4 ip 0x6000
Initializing CPU#2
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU2: Thermal monitoring enabled (TM1)
CPU 2 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
CPU2: Intel(R) Xeon(R) CPU X3430 @ 2.40GHz stepping 05
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
Booting processor 3 APIC 0x6 ip 0x6000
Initializing CPU#3
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU3: Thermal monitoring enabled (TM1)
CPU 3 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
CPU3: Intel(R) Xeon(R) CPU X3430 @ 2.40GHz stepping 05
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
Total of 4 processors activated (19159.55 BogoMIPS).
xor: automatically using best checksumming function: generic_sse
generic_sse: 9436.400 MB/sec
xor: using function: generic_sse (9436.400 MB/sec)
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI Error (psargs-0359): [CDW1] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_._OSC] (Node ffff88033f852690), AE_NOT_FOUND
ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:1a.0: reg 10 32bit mmio: [0xdf0fc000-0xdf0fc3ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1d.0: reg 10 32bit mmio: [0xdf0fe000-0xdf0fe3ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: PME# disabled
pci 0000:00:1f.2: reg 10 io port: [0xeca0-0xeca7]
pci 0000:00:1f.2: reg 14 io port: [0xec90-0xec93]
pci 0000:00:1f.2: reg 18 io port: [0xeca8-0xecaf]
pci 0000:00:1f.2: reg 1c io port: [0xec94-0xec97]
pci 0000:00:1f.2: reg 20 io port: [0xecc0-0xeccf]
pci 0000:00:1f.2: reg 24 io port: [0xecd0-0xecdf]
pci 0000:00:1f.5: reg 10 io port: [0xecb0-0xecb7]
pci 0000:00:1f.5: reg 14 io port: [0xec98-0xec9b]
pci 0000:00:1f.5: reg 18 io port: [0xecb8-0xecbf]
pci 0000:00:1f.5: reg 1c io port: [0xec9c-0xec9f]
pci 0000:00:1f.5: reg 20 io port: [0xece0-0xecef]
pci 0000:00:1f.5: reg 24 io port: [0xecf0-0xecff]
pci 0000:02:00.0: reg 10 64bit mmio: [0xda000000-0xdbffffff]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:00.1: reg 10 64bit mmio: [0xdc000000-0xddffffff]
pci 0000:02:00.1: PME# supported from D0 D3hot D3cold
pci 0000:02:00.1: PME# disabled
pci 0000:00:1c.0: bridge 32bit mmio: [0xda000000-0xddffffff]
pci 0000:05:00.0: reg 10 32bit mmio: [0xdf1fe000-0xdf1fffff]
pci 0000:05:00.0: PME# supported from D0 D3hot
pci 0000:05:00.0: PME# disabled
pci 0000:00:1c.4: bridge io port: [0xf000-0xffff]
pci 0000:00:1c.4: bridge 32bit mmio: [0xdf100000-0xdf3fffff]
pci 0000:06:08.0: reg 10 io port: [0xfc00-0xfcff]
pci 0000:06:08.0: reg 14 64bit mmio: [0xdf3c0000-0xdf3dffff]
pci 0000:06:08.0: reg 1c 64bit mmio: [0xdf3e0000-0xdf3fffff]
pci 0000:06:08.0: reg 30 32bit mmio pref: [0xdf200000-0xdf2fffff]
pci 0000:06:08.0: supports D1 D2
pci 0000:05:00.0: bridge io port: [0xf000-0xffff]
pci 0000:05:00.0: bridge 32bit mmio: [0xdf200000-0xdf3fffff]
pci 0000:01:03.0: reg 10 32bit mmio pref: [0xd9800000-0xd9ffffff]
pci 0000:01:03.0: reg 14 32bit mmio: [0xde7fc000-0xde7fffff]
pci 0000:01:03.0: reg 18 32bit mmio: [0xde800000-0xdeffffff]
pci 0000:01:03.0: reg 30 32bit mmio pref: [0x000000-0x00ffff]
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xde000000-0xdeffffff]
pci 0000:00:1e.0: bridge 64bit mmio pref: [0xd9800000-0xd9ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.LYD0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.LYD2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 11 14 *15)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 *6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 *14 15)
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
vgaarb: device added: PCI:0000:01:03.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
raid6: int64x1 2728 MB/s
raid6: int64x2 3108 MB/s
raid6: int64x4 2226 MB/s
raid6: int64x8 1976 MB/s
raid6: sse2x1 6280 MB/s
raid6: sse2x2 7368 MB/s
raid6: sse2x4 8577 MB/s
raid6: using algorithm sse2x4 (8577 MB/s)
PCI: Using ACPI for IRQ routing
hpet: hpet2 irq 24 for MSI
hpet: hpet3 irq 25 for MSI
hpet: hpet4 irq 26 for MSI
hpet: hpet5 irq 27 for MSI
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x880-0x8ff has been reserved
system 00:07: ioport range 0x900-0x91f has been reserved
system 00:07: ioport range 0x920-0x923 has been reserved
system 00:07: ioport range 0x924-0x924 has been reserved
system 00:07: ioport range 0xca0-0xca7 has been reserved
system 00:07: ioport range 0xca9-0xcab has been reserved
system 00:07: ioport range 0xcad-0xcaf has been reserved
system 00:08: ioport range 0xca8-0xca8 has been reserved
system 00:08: ioport range 0xcac-0xcac has been reserved
system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0c: iomem range 0xfed50000-0xfed51fff has been reserved
pci 0000:00:03.0: PCI bridge, secondary bus 0000:04
pci 0000:00:03.0: IO window: disabled
pci 0000:00:03.0: MEM window: disabled
pci 0000:00:03.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: disabled
pci 0000:00:1c.0: MEM window: 0xda000000-0xddffffff
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:07
pci 0000:00:1c.2: IO window: disabled
pci 0000:00:1c.2: MEM window: disabled
pci 0000:00:1c.2: PREFETCH window: disabled
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:08
pci 0000:00:1c.3: IO window: disabled
pci 0000:00:1c.3: MEM window: disabled
pci 0000:00:1c.3: PREFETCH window: disabled
pci 0000:05:00.0: PCI bridge, secondary bus 0000:06
pci 0000:05:00.0: IO window: 0xf000-0xffff
pci 0000:05:00.0: MEM window: 0xdf200000-0xdf3fffff
pci 0000:05:00.0: PREFETCH window: disabled
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:05
pci 0000:00:1c.4: IO window: 0xf000-0xffff
pci 0000:00:1c.4: MEM window: 0xdf100000-0xdf3fffff
pci 0000:00:1c.4: PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: 0xde000000-0xdeffffff
pci 0000:00:1e.0: PREFETCH window: 0x000000d9800000-0x000000d9ffffff
pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:03.0: setting latency timer to 64
pci 0000:00:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:05:00.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:02: resource 1 mem: [0xda000000-0xddffffff]
pci_bus 0000:05: resource 0 io: [0xf000-0xffff]
pci_bus 0000:05: resource 1 mem: [0xdf100000-0xdf3fffff]
pci_bus 0000:06: resource 0 io: [0xf000-0xffff]
pci_bus 0000:06: resource 1 mem: [0xdf200000-0xdf3fffff]
pci_bus 0000:01: resource 1 mem: [0xde000000-0xdeffffff]
pci_bus 0000:01: resource 2 pref mem [0xd9800000-0xd9ffffff]
pci_bus 0000:01: resource 3 io: [0x00-0xffff]
pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0000:01:03.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 2943k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1272367671.000:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.5.0
ocfs2: Registered cluster interface o2cb
OCFS2 Node Manager 1.5.0
OCFS2 DLM 1.5.0
OCFS2 DLMFS 1.5.0
OCFS2 User DLM kernel interface loaded
Slow work thread pool: Starting up
Slow work thread pool: Ready
GFS2 (built Apr 26 2010 08:21:00) installed
msgmni has been set to 24022
alg: No test for stdrng (krng)
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:03.0: irq 30 for MSI/MSI-X
pcieport 0000:00:03.0: setting latency timer to 64
pcieport 0000:00:05.0: irq 31 for MSI/MSI-X
pcieport 0000:00:05.0: setting latency timer to 64
pcieport 0000:00:1c.0: irq 32 for MSI/MSI-X
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.2: irq 33 for MSI/MSI-X
pcieport 0000:00:1c.2: setting latency timer to 64
pcieport 0000:00:1c.3: irq 34 for MSI/MSI-X
pcieport 0000:00:1c.3: setting latency timer to 64
pcieport 0000:00:1c.4: irq 35 for MSI/MSI-X
pcieport 0000:00:1c.4: setting latency timer to 64
aer 0000:00:03.0:pcie02: service driver aer loaded
aer 0000:00:05.0:pcie02: service driver aer loaded
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Probing IDE interface ide0...
ide0: no devices on the port
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide1: no devices on the port
ide1 at 0x170-0x177,0x376 on irq 15
ide-gd driver 1.18
ide-cd driver 5.00
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 420k freed
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.13
ata_piix 0000:00:1f.2: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xeca0 ctl 0xec90 bmdma 0xecc0 irq 20
ata2: SATA max UDMA/133 cmd 0xeca8 ctl 0xec94 bmdma 0xecc8 irq 20
ata_piix 0000:00:1f.5: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ata_piix 0000:00:1f.5: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xecb0 ctl 0xec98 bmdma 0xece0 irq 21
ata4: SATA max UDMA/133 cmd 0xecb8 ctl 0xec9c bmdma 0xece8 irq 21
ata4: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: PLDS DVD-ROM DH-16D5S, VD15, max UDMA/100
ata3.00: configured for UDMA/100
ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.01: SATA link up <unknown> (SStatus 300 SControl 123)
ata2.00: link offline, clearing class 1 to NONE
ata1.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.01: ATA-8: ST3250310NS, MA0D, max UDMA/133
ata2.01: 488281250 sectors, multi 8: LBA48 NCQ (depth 0/32)
ata1.00: ATA-8: ST3250310NS, MA0D, max UDMA/133
ata1.00: 488281250 sectors, multi 8: LBA48 NCQ (depth 0/32)
ata1.01: ATA-8: ST3250310NS, MA0D, max UDMA/133
ata1.01: 488281250 sectors, multi 8: LBA48 NCQ (depth 0/32)
ata2.01: configured for UDMA/133
ata1.00: configured for UDMA/133
ata1.01: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3250310NS n/a PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access ATA ST3250310NS n/a PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
scsi 1:0:1:0: Direct-Access ATA ST3250310NS n/a PQ: 0 ANSI: 5
sd 1:0:1:0: [sdc] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:1:0: [sdc] Write Protect is off
sd 1:0:1:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc:
scsi 2:0:0:0: CD-ROM PLDS DVD-ROM DH-16D5S VD15 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sda1 sda2 sda3 sda4
sd 0:0:1:0: [sdb] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sdc1 sdc2 sdc3 sdc4
sd 1:0:1:0: [sdc] Attached SCSI disk
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:1:0: [sdb] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
sd 1:0:1:0: Attached scsi generic sg2 type 0
sr 2:0:0:0: Attached scsi generic sg3 type 5
scsi: <fdomain> Detection failed (no card)
GDT-HA: Storage RAID Controller Driver. Version: 3.05
imm: Version 2.05 (for Linux 2.4.0)
Fusion MPT base driver 3.04.12
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.12
mptspi 0000:06:08.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
mptbase: ioc0: Initiating bringup
ioc0: LSI53C1020A A1: Capabilities={Initiator,Target}
scsi4 : ioc0: LSI53C1020A A1, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=16
Fusion MPT FC Host driver 3.04.12
Fusion MPT SAS Host driver 3.04.12
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.012.
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.20)
Adaptec aacraid driver 1.1-5[2461]-ms
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
QLogic Fibre Channel HBA Driver: 8.03.01-k6
Emulex LightPulse Fibre Channel SCSI driver 8.3.4
Copyright(c) 2004-2009 Emulex. All rights reserved.
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1a.0: setting latency timer to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
ehci_hcd 0000:00:1a.0: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.0: irq 22, io mem 0xdf0fc000
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1d.0: setting latency timer to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
ehci_hcd 0000:00:1d.0: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.0: irq 22, io mem 0xdf0fe000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
uhci_hcd: USB Universal Host Controller Interface driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb 1-1: new high speed USB device using ehci_hcd and address 2
scsi 4:0:6:0: Sequential-Access IBM ULTRIUM-HH3 93G7 PQ: 0 ANSI: 3
scsi target4:0:6: Beginning Domain Validation
sl811: driver sl811-hcd, 19 May 2005
scsi target4:0:6: Domain Validation skipping write tests
scsi target4:0:6: Ending Domain Validation
scsi target4:0:6: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 127)
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
usb 2-1: new high speed USB device using ehci_hcd and address 2
scsi: waiting for bus probes to complete ...
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
usb 1-1.1: new high speed USB device using ehci_hcd and address 3
usb 1-1.1: configuration #1 chosen from 1 choice
hub 1-1.1:1.0: USB hub found
hub 1-1.1:1.0: 2 ports detected
usb 2-1.4: new low speed USB device using ehci_hcd and address 3
usb 2-1.4: configuration #1 chosen from 1 choice
input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input1
generic-usb 0003:413C:2105.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.0-1.4/input0
scsi 4:0:6:0: Attached scsi generic sg4 type 1
JFS: nTxBlock = 8192, nTxLock = 65536
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
fuse init (API version 7.13)
Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI
Copyright (c) 1999-2006 Intel Corporation.
md: Autodetecting RAID arrays.
md: Scanned 9 and added 9 devices.
md: autorun ...
md: considering sdb4 ...
md: adding sdb4 ...
md: sdb3 has different UUID to sdb4
md: sdb1 has different UUID to sdb4
md: adding sda4 ...
md: sda3 has different UUID to sdb4
md: sda1 has different UUID to sdb4
md: adding sdc4 ...
md: sdc3 has different UUID to sdb4
md: sdc1 has different UUID to sdb4
md: created md4
md: bind<sdc4>
md: bind<sda4>
md: bind<sdb4>
md: running: <sdb4><sda4><sdc4>
raid5: device sdb4 operational as raid disk 1
raid5: device sda4 operational as raid disk 0
raid5: device sdc4 operational as raid disk 3
raid5: allocated 4272kB for md4
1: w=1 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
0: w=2 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
3: w=3 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
raid5: raid level 5 set md4 active with 3 out of 4 devices, algorithm 2
RAID5 conf printout:
--- rd:4 wd:3
disk 0, o:1, dev:sda4
disk 1, o:1, dev:sdb4
disk 3, o:1, dev:sdc4
md4: detected capacity change from 0 to 731292893184
md: considering sdb3 ...
md: adding sdb3 ...
md: sdb1 has different UUID to sdb3
md: adding sda3 ...
md: sda1 has different UUID to sdb3
md: adding sdc3 ...
md: sdc1 has different UUID to sdb3
md: created md3
md: bind<sdc3>
md: bind<sda3>
md: bind<sdb3>
md: running: <sdb3><sda3><sdc3>
raid10: raid set md3 active with 3 out of 4 devices
md3: detected capacity change from 0 to 10232004608
md: considering sdb1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: adding sdc1 ...
md: created md1
md: bind<sdc1>
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1><sdc1>
raid1: raid set md1 active with 3 out of 4 mirrors
md1: detected capacity change from 0 to 98566144
md: ... autorun DONE.
md3: unknown partition table
EXT3-fs: md3: couldn't mount because of unsupported optional features (240).
EXT2-fs: md3: couldn't mount because of unsupported optional features (240).
EXT4-fs (md3): mounted filesystem with ordered data mode
udev: starting version 149
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
md4:
md1:
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-3 state
processor LNXCPU:00: registered as cooling_device0
processor LNXCPU:01: registered as cooling_device1
processor LNXCPU:02: registered as cooling_device2
processor LNXCPU:03: registered as cooling_device3
unknown partition table
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
unknown partition table
input: PC Speaker as /devices/platform/pcspkr/input/input3
st: Version 20081215, fixed bufsize 32768, s/g segs 256
st 4:0:6:0: Attached scsi tape st0
st 4:0:6:0: st0: try direct i/o: yes (alignment 4 B)
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.0.2 (Aug 21, 2009)
bnx2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
bnx2 0000:02:00.0: setting latency timer to 64
bnx2 0000:02:00.0: firmware: requesting bnx2/bnx2-mips-09-5.0.0.j3.fw
rtc_cmos 00:04: RTC can wake from S4
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day, y3k, 242 bytes nvram, hpet irqs
bnx2 0000:02:00.0: firmware: requesting bnx2/bnx2-rv2p-09-5.0.0.j3.fw
eth0: Broadcom NetXtreme II BCM5716 1000Base-T (C0) PCI Express found at mem da000000, IRQ 16, node addr 00:26:b9:3d:47:19
bnx2 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
bnx2 0000:02:00.1: setting latency timer to 64
bnx2 0000:02:00.1: firmware: requesting bnx2/bnx2-mips-09-5.0.0.j3.fw
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
bnx2 0000:02:00.1: firmware: requesting bnx2/bnx2-rv2p-09-5.0.0.j3.fw
eth1: Broadcom NetXtreme II BCM5716 1000Base-T (C0) PCI Express found at mem dc000000, IRQ 17, node addr 00:26:b9:3d:47:1a
vboxdrv: Trying to deactivate the NMI watchdog permanently...
vboxdrv: Successfully done.
vboxdrv: Found 4 processor cores.
VBoxDrv: dbg - g_abExecMemory=ffffffffa0537f20
vboxdrv: fAsync=0 offMin=0x94e offMax=0x22bfa
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 3.1.6 (interface 0x00100001).
EXT4-fs (dm-2): mounted filesystem with ordered data mode
EXT4-fs (dm-1): mounted filesystem with ordered data mode
EXT4-fs (dm-3): mounted filesystem with ordered data mode
EXT4-fs (dm-0): mounted filesystem with ordered data mode
EXT4-fs (dm-4): mounted filesystem with ordered data mode
Adding 996020k swap on /dev/sda2. Priority:-1 extents:1 across:996020k
Adding 996020k swap on /dev/sdb2. Priority:-2 extents:1 across:996020k
Adding 996020k swap on /dev/sdc2. Priority:-3 extents:1 across:996020k
lapic_id[0x2f] disabled)
ACPI: LAPIC (acpi_id[0x11] lapic_id[0x30] disabled)
ACPI: LAPIC (acpi_id[0x12] lapic_id[0x31] disabled)
ACPI: LAPIC (acpi_id[0x13] lapic_id[0x32] disabled)
ACPI: LAPIC (acpi_id[0x14] lapic_id[0x33] disabled)
ACPI: LAPIC (acpi_id[0x15] lapic_id[0x34] disabled)
ACPI: LAPIC (acpi_id[0x16] lapic_id[0x35] disabled)
ACPI: LAPIC (acpi_id[0x17] lapic_id[0x36] disabled)
ACPI: LAPIC (acpi_id[0x18] lapic_id[0x37] disabled)
ACPI: LAPIC (acpi_id[0x19] lapic_id[0x38] disabled)
ACPI: LAPIC (acpi_id[0x1a] lapic_id[0x39] disabled)
ACPI: LAPIC (acpi_id[0x1b] lapic_id[0x3a] disabled)
ACPI: LAPIC (acpi_id[0x1c] lapic_id[0x3b] disabled)
ACPI: LAPIC (acpi_id[0x1d] lapic_id[0x3c] disabled)
ACPI: LAPIC (acpi_id[0x1e] lapic_id[0x3d] disabled)
ACPI: LAPIC (acpi_id[0x1f] lapic_id[0x3e] disabled)
ACPI: LAPIC (acpi_id[0x20] lapic_id[0x3f] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a701 base: 0xfed00000
SMP: Allowing 32 CPUs, 28 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 0000000000100000
PM: Registered nosave memory: 00000000bf699000 - 00000000bf6af000
PM: Registered nosave memory: 00000000bf6af000 - 00000000bf6ce000
PM: Registered nosave memory: 00000000bf6ce000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000fe000000
PM: Registered nosave memory: 00000000fe000000 - 0000000100000000
Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:32 nr_node_ids:1
PERCPU: Embedded 24 pages/cpu @ffff880032e00000 s68632 r8192 d21480 u131072
pcpu-alloc: s68632 r8192 d21480 u131072 alloc=1*2097152
pcpu-alloc: [0] 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
pcpu-alloc: [0] 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 3096521
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/md3 libata.force=nohrst
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Initializing CPU#0
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
software IO TLB at phys 0x20000000 - 0x24000000
Memory: 12295696k/13631488k available (4401k kernel code, 1058592k absent, 276248k reserved, 1675k data, 420k init)
Hierarchical RCU implementation.
NR_IRQS:1280
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
HPET: 8 timers in total, 6 timers will be used for per-cpu timer
Fast TSC calibration using PIT
Detected 2394.640 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4789.28 BogoMIPS (lpj=23946400)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
mce: CPU supports 9 MCE banks
CPU0: Thermal monitoring enabled (TM1)
CPU 0 MCA banks CMCI:2 CMCI:3 CMCI:5 CMCI:6 CMCI:8
using mwait in idle threads.
ACPI: Core revision 20090903
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Xeon(R) CPU X3430 @ 2.40GHz stepping 05
Booting processor 1 APIC 0x2 ip 0x6000
Initializing CPU#1
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU1: Thermal monitoring enabled (TM1)
CPU 1 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
CPU1: Intel(R) Xeon(R) CPU X3430 @ 2.40GHz stepping 05
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Booting processor 2 APIC 0x4 ip 0x6000
Initializing CPU#2
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU2: Thermal monitoring enabled (TM1)
CPU 2 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
CPU2: Intel(R) Xeon(R) CPU X3430 @ 2.40GHz stepping 05
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
Booting processor 3 APIC 0x6 ip 0x6000
Initializing CPU#3
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU3: Thermal monitoring enabled (TM1)
CPU 3 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
CPU3: Intel(R) Xeon(R) CPU X3430 @ 2.40GHz stepping 05
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
Total of 4 processors activated (19158.91 BogoMIPS).
xor: automatically using best checksumming function: generic_sse
generic_sse: 9435.600 MB/sec
xor: using function: generic_sse (9435.600 MB/sec)
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI Error (psargs-0359): [CDW1] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_._OSC] (Node ffff88033f852690), AE_NOT_FOUND
ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:1a.0: reg 10 32bit mmio: [0xdf0fc000-0xdf0fc3ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1d.0: reg 10 32bit mmio: [0xdf0fe000-0xdf0fe3ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: PME# disabled
pci 0000:00:1f.2: reg 10 io port: [0xeca0-0xeca7]
pci 0000:00:1f.2: reg 14 io port: [0xec90-0xec93]
pci 0000:00:1f.2: reg 18 io port: [0xeca8-0xecaf]
pci 0000:00:1f.2: reg 1c io port: [0xec94-0xec97]
pci 0000:00:1f.2: reg 20 io port: [0xecc0-0xeccf]
pci 0000:00:1f.2: reg 24 io port: [0xecd0-0xecdf]
pci 0000:00:1f.5: reg 10 io port: [0xecb0-0xecb7]
pci 0000:00:1f.5: reg 14 io port: [0xec98-0xec9b]
pci 0000:00:1f.5: reg 18 io port: [0xecb8-0xecbf]
pci 0000:00:1f.5: reg 1c io port: [0xec9c-0xec9f]
pci 0000:00:1f.5: reg 20 io port: [0xece0-0xecef]
pci 0000:00:1f.5: reg 24 io port: [0xecf0-0xecff]
pci 0000:02:00.0: reg 10 64bit mmio: [0xda000000-0xdbffffff]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:00.1: reg 10 64bit mmio: [0xdc000000-0xddffffff]
pci 0000:02:00.1: PME# supported from D0 D3hot D3cold
pci 0000:02:00.1: PME# disabled
pci 0000:00:1c.0: bridge 32bit mmio: [0xda000000-0xddffffff]
pci 0000:05:00.0: reg 10 32bit mmio: [0xdf1fe000-0xdf1fffff]
pci 0000:05:00.0: PME# supported from D0 D3hot
pci 0000:05:00.0: PME# disabled
pci 0000:00:1c.4: bridge io port: [0xf000-0xffff]
pci 0000:00:1c.4: bridge 32bit mmio: [0xdf100000-0xdf3fffff]
pci 0000:06:08.0: reg 10 io port: [0xfc00-0xfcff]
pci 0000:06:08.0: reg 14 64bit mmio: [0xdf3c0000-0xdf3dffff]
pci 0000:06:08.0: reg 1c 64bit mmio: [0xdf3e0000-0xdf3fffff]
pci 0000:06:08.0: reg 30 32bit mmio pref: [0xdf200000-0xdf2fffff]
pci 0000:06:08.0: supports D1 D2
pci 0000:05:00.0: bridge io port: [0xf000-0xffff]
pci 0000:05:00.0: bridge 32bit mmio: [0xdf200000-0xdf3fffff]
pci 0000:01:03.0: reg 10 32bit mmio pref: [0xd9800000-0xd9ffffff]
pci 0000:01:03.0: reg 14 32bit mmio: [0xde7fc000-0xde7fffff]
pci 0000:01:03.0: reg 18 32bit mmio: [0xde800000-0xdeffffff]
pci 0000:01:03.0: reg 30 32bit mmio pref: [0x000000-0x00ffff]
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xde000000-0xdeffffff]
pci 0000:00:1e.0: bridge 64bit mmio pref: [0xd9800000-0xd9ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.LYD0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.LYD2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 11 14 *15)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 *6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 *14 15)
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
vgaarb: device added: PCI:0000:01:03.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
raid6: int64x1 2727 MB/s
raid6: int64x2 3107 MB/s
raid6: int64x4 2229 MB/s
raid6: int64x8 1976 MB/s
raid6: sse2x1 6264 MB/s
raid6: sse2x2 7356 MB/s
raid6: sse2x4 8573 MB/s
raid6: using algorithm sse2x4 (8573 MB/s)
PCI: Using ACPI for IRQ routing
hpet: hpet2 irq 24 for MSI
hpet: hpet3 irq 25 for MSI
hpet: hpet4 irq 26 for MSI
hpet: hpet5 irq 27 for MSI
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x880-0x8ff has been reserved
system 00:07: ioport range 0x900-0x91f has been reserved
system 00:07: ioport range 0x920-0x923 has been reserved
system 00:07: ioport range 0x924-0x924 has been reserved
system 00:07: ioport range 0xca0-0xca7 has been reserved
system 00:07: ioport range 0xca9-0xcab has been reserved
system 00:07: ioport range 0xcad-0xcaf has been reserved
system 00:08: ioport range 0xca8-0xca8 has been reserved
system 00:08: ioport range 0xcac-0xcac has been reserved
system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0c: iomem range 0xfed50000-0xfed51fff has been reserved
pci 0000:00:03.0: PCI bridge, secondary bus 0000:04
pci 0000:00:03.0: IO window: disabled
pci 0000:00:03.0: MEM window: disabled
pci 0000:00:03.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: disabled
pci 0000:00:1c.0: MEM window: 0xda000000-0xddffffff
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:07
pci 0000:00:1c.2: IO window: disabled
pci 0000:00:1c.2: MEM window: disabled
pci 0000:00:1c.2: PREFETCH window: disabled
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:08
pci 0000:00:1c.3: IO window: disabled
pci 0000:00:1c.3: MEM window: disabled
pci 0000:00:1c.3: PREFETCH window: disabled
pci 0000:05:00.0: PCI bridge, secondary bus 0000:06
pci 0000:05:00.0: IO window: 0xf000-0xffff
pci 0000:05:00.0: MEM window: 0xdf200000-0xdf3fffff
pci 0000:05:00.0: PREFETCH window: disabled
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:05
pci 0000:00:1c.4: IO window: 0xf000-0xffff
pci 0000:00:1c.4: MEM window: 0xdf100000-0xdf3fffff
pci 0000:00:1c.4: PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: 0xde000000-0xdeffffff
pci 0000:00:1e.0: PREFETCH window: 0x000000d9800000-0x000000d9ffffff
pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:03.0: setting latency timer to 64
pci 0000:00:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:05:00.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:02: resource 1 mem: [0xda000000-0xddffffff]
pci_bus 0000:05: resource 0 io: [0xf000-0xffff]
pci_bus 0000:05: resource 1 mem: [0xdf100000-0xdf3fffff]
pci_bus 0000:06: resource 0 io: [0xf000-0xffff]
pci_bus 0000:06: resource 1 mem: [0xdf200000-0xdf3fffff]
pci_bus 0000:01: resource 1 mem: [0xde000000-0xdeffffff]
pci_bus 0000:01: resource 2 pref mem [0xd9800000-0xd9ffffff]
pci_bus 0000:01: resource 3 io: [0x00-0xffff]
pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0000:01:03.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 2943k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1272355228.050:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.5.0
ocfs2: Registered cluster interface o2cb
OCFS2 Node Manager 1.5.0
OCFS2 DLM 1.5.0
OCFS2 DLMFS 1.5.0
OCFS2 User DLM kernel interface loaded
Slow work thread pool: Starting up
Slow work thread pool: Ready
GFS2 (built Apr 26 2010 08:21:00) installed
msgmni has been set to 24022
alg: No test for stdrng (krng)
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:03.0: irq 30 for MSI/MSI-X
pcieport 0000:00:03.0: setting latency timer to 64
pcieport 0000:00:05.0: irq 31 for MSI/MSI-X
pcieport 0000:00:05.0: setting latency timer to 64
pcieport 0000:00:1c.0: irq 32 for MSI/MSI-X
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.2: irq 33 for MSI/MSI-X
pcieport 0000:00:1c.2: setting latency timer to 64
pcieport 0000:00:1c.3: irq 34 for MSI/MSI-X
pcieport 0000:00:1c.3: setting latency timer to 64
pcieport 0000:00:1c.4: irq 35 for MSI/MSI-X
pcieport 0000:00:1c.4: setting latency timer to 64
aer 0000:00:03.0:pcie02: service driver aer loaded
aer 0000:00:05.0:pcie02: service driver aer loaded
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Probing IDE interface ide0...
ide0: no devices on the port
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide1: no devices on the port
ide1 at 0x170-0x177,0x376 on irq 15
ide-gd driver 1.18
ide-cd driver 5.00
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 420k freed
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.13
ata_piix 0000:00:1f.2: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xeca0 ctl 0xec90 bmdma 0xecc0 irq 20
ata2: SATA max UDMA/133 cmd 0xeca8 ctl 0xec94 bmdma 0xecc8 irq 20
ata_piix 0000:00:1f.5: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ata_piix 0000:00:1f.5: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xecb0 ctl 0xec98 bmdma 0xece0 irq 21
ata4: SATA max UDMA/133 cmd 0xecb8 ctl 0xec9c bmdma 0xece8 irq 21
ata4: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: PLDS DVD-ROM DH-16D5S, VD15, max UDMA/100
ata3.00: configured for UDMA/100
ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: ST3250310NS, MA0D, max UDMA/133
ata1.00: 488281250 sectors, multi 8: LBA48 NCQ (depth 0/32)
ata2.00: ATA-8: ST3250310NS, MA0D, max UDMA/133
ata2.00: 488281250 sectors, multi 8: LBA48 NCQ (depth 0/32)
ata1.01: ATA-8: ST3250310NS, MA0D, max UDMA/133
ata1.01: 488281250 sectors, multi 8: LBA48 NCQ (depth 0/32)
ata2.01: ATA-8: ST3250310NS, MA0D, max UDMA/133
ata2.01: 488281250 sectors, multi 8: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2.00: configured for UDMA/133
ata1.01: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3250310NS n/a PQ: 0 ANSI: 5
ata2.01: configured for UDMA/133
scsi 0:0:1:0: Direct-Access ATA ST3250310NS n/a PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
scsi 1:0:0:0: Direct-Access ATA ST3250310NS n/a PQ: 0 ANSI: 5
sd 1:0:0:0: [sdc] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sdc] Write Protect is off
sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
scsi 1:0:1:0: Direct-Access ATA ST3250310NS n/a PQ: 0 ANSI: 5
sdc:
scsi 2:0:0:0: CD-ROM PLDS DVD-ROM DH-16D5S VD15 PQ: 0 ANSI: 5
sda1 sda2 sda3 sda4
sd 0:0:1:0: [sdb] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sdc1 sdc2 sdc3 sdc4
sd 1:0:1:0: [sdd] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
sd 1:0:1:0: [sdd] Write Protect is off
sd 1:0:1:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdb1 sdb2 sdb3 sdb4
sdd1 sdd2 sdd3 sdd4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:1:0: [sdb] Attached SCSI disk
sd 1:0:0:0: [sdc] Attached SCSI disk
sd 1:0:1:0: [sdd] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: Attached scsi generic sg2 type 0
sd 1:0:1:0: Attached scsi generic sg3 type 0
sr 2:0:0:0: Attached scsi generic sg4 type 5
scsi: <fdomain> Detection failed (no card)
GDT-HA: Storage RAID Controller Driver. Version: 3.05
imm: Version 2.05 (for Linux 2.4.0)
Fusion MPT base driver 3.04.12
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.12
mptspi 0000:06:08.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
mptbase: ioc0: Initiating bringup
ioc0: LSI53C1020A A1: Capabilities={Initiator,Target}
scsi4 : ioc0: LSI53C1020A A1, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=16
Fusion MPT FC Host driver 3.04.12
Fusion MPT SAS Host driver 3.04.12
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.012.
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.20)
Adaptec aacraid driver 1.1-5[2461]-ms
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
QLogic Fibre Channel HBA Driver: 8.03.01-k6
Emulex LightPulse Fibre Channel SCSI driver 8.3.4
Copyright(c) 2004-2009 Emulex. All rights reserved.
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1a.0: setting latency timer to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
ehci_hcd 0000:00:1a.0: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.0: irq 22, io mem 0xdf0fc000
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1d.0: setting latency timer to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
ehci_hcd 0000:00:1d.0: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.0: irq 22, io mem 0xdf0fe000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
uhci_hcd: USB Universal Host Controller Interface driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb 1-1: new high speed USB device using ehci_hcd and address 2
scsi 4:0:6:0: Sequential-Access IBM ULTRIUM-HH3 93G7 PQ: 0 ANSI: 3
scsi target4:0:6: Beginning Domain Validation
sl811: driver sl811-hcd, 19 May 2005
scsi target4:0:6: Ending Domain Validation
scsi target4:0:6: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 127)
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
usb 2-1: new high speed USB device using ehci_hcd and address 2
scsi: waiting for bus probes to complete ...
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
usb 1-1.1: new high speed USB device using ehci_hcd and address 3
usb 1-1.1: configuration #1 chosen from 1 choice
hub 1-1.1:1.0: USB hub found
hub 1-1.1:1.0: 2 ports detected
usb 2-1.4: new low speed USB device using ehci_hcd and address 3
usb 2-1.4: configuration #1 chosen from 1 choice
input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input1
generic-usb 0003:413C:2105.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.0-1.4/input0
scsi 4:0:6:0: Attached scsi generic sg5 type 1
JFS: nTxBlock = 8192, nTxLock = 65536
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
fuse init (API version 7.13)
Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI
Copyright (c) 1999-2006 Intel Corporation.
md: Autodetecting RAID arrays.
md: Scanned 12 and added 12 devices.
md: autorun ...
md: considering sdd4 ...
md: adding sdd4 ...
md: sdd3 has different UUID to sdd4
md: sdd1 has different UUID to sdd4
md: adding sdb4 ...
md: sdb3 has different UUID to sdd4
md: sdb1 has different UUID to sdd4
md: adding sdc4 ...
md: sdc3 has different UUID to sdd4
md: sdc1 has different UUID to sdd4
md: adding sda4 ...
md: sda3 has different UUID to sdd4
md: sda1 has different UUID to sdd4
md: created md4
md: bind<sda4>
md: bind<sdc4>
md: bind<sdb4>
md: bind<sdd4>
md: running: <sdd4><sdb4><sdc4><sda4>
raid5: device sdd4 operational as raid disk 3
raid5: device sdb4 operational as raid disk 1
raid5: device sdc4 operational as raid disk 2
raid5: device sda4 operational as raid disk 0
raid5: allocated 4272kB for md4
3: w=1 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
1: w=2 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
2: w=3 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
0: w=4 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
raid5: raid level 5 set md4 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
--- rd:4 wd:4
disk 0, o:1, dev:sda4
disk 1, o:1, dev:sdb4
disk 2, o:1, dev:sdc4
disk 3, o:1, dev:sdd4
md4: detected capacity change from 0 to 731292893184
md: considering sdd3 ...
md: adding sdd3 ...
md: sdd1 has different UUID to sdd3
md: adding sdb3 ...
md: sdb1 has different UUID to sdd3
md: adding sdc3 ...
md: sdc1 has different UUID to sdd3
md: adding sda3 ...
md: sda1 has different UUID to sdd3
md: created md3
md: bind<sda3>
md: bind<sdc3>
md: bind<sdb3>
md: bind<sdd3>
md: running: <sdd3><sdb3><sdc3><sda3>
raid10: raid set md3 active with 4 out of 4 devices
md3: detected capacity change from 0 to 10232004608
md: considering sdd1 ...
md: adding sdd1 ...
md: adding sdb1 ...
md: adding sdc1 ...
md: adding sda1 ...
md: created md1
md: bind<sda1>
md: bind<sdc1>
md: bind<sdb1>
md: bind<sdd1>
md: running: <sdd1><sdb1><sdc1><sda1>
raid1: raid set md1 active with 4 out of 4 mirrors
md1: detected capacity change from 0 to 98566144
md: ... autorun DONE.
md3: unknown partition table
EXT3-fs: md3: couldn't mount because of unsupported optional features (240).
EXT2-fs: md3: couldn't mount because of unsupported optional features (240).
EXT4-fs (md3): mounted filesystem with ordered data mode
udev: starting version 149
Monitor-Mwait will be used to enter C-1 state
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
input: PC Speaker as /devices/platform/pcspkr/input/input2
Monitor-Mwait will be used to enter C-3 state
processor LNXCPU:00: registered as cooling_device0
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button [PWRF]
processor LNXCPU:01: registered as cooling_device1
processor LNXCPU:02: registered as cooling_device2
processor LNXCPU:03: registered as cooling_device3
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.0.2 (Aug 21, 2009)
bnx2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
bnx2 0000:02:00.0: setting latency timer to 64
bnx2 0000:02:00.0: firmware: requesting bnx2/bnx2-mips-09-5.0.0.j3.fw
md4:
md1:
rtc_cmos 00:04: RTC can wake from S4
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day, y3k, 242 bytes nvram, hpet irqs
st: Version 20081215, fixed bufsize 32768, s/g segs 256
st 4:0:6:0: Attached scsi tape st0
st 4:0:6:0: st0: try direct i/o: yes (alignment 4 B)
unknown partition table
unknown partition table
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
bnx2 0000:02:00.0: firmware: requesting bnx2/bnx2-rv2p-09-5.0.0.j3.fw
eth0: Broadcom NetXtreme II BCM5716 1000Base-T (C0) PCI Express found at mem da000000, IRQ 16, node addr 00:26:b9:3d:47:19
bnx2 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
bnx2 0000:02:00.1: setting latency timer to 64
bnx2 0000:02:00.1: firmware: requesting bnx2/bnx2-mips-09-5.0.0.j3.fw
bnx2 0000:02:00.1: firmware: requesting bnx2/bnx2-rv2p-09-5.0.0.j3.fw
eth1: Broadcom NetXtreme II BCM5716 1000Base-T (C0) PCI Express found at mem dc000000, IRQ 17, node addr 00:26:b9:3d:47:1a
vboxdrv: Trying to deactivate the NMI watchdog permanently...
vboxdrv: Successfully done.
vboxdrv: Found 4 processor cores.
VBoxDrv: dbg - g_abExecMemory=ffffffffa0537f20
vboxdrv: fAsync=0 offMin=0x96a offMax=0x24704
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 3.1.6 (interface 0x00100001).
EXT4-fs (dm-2): mounted filesystem with ordered data mode
EXT4-fs (dm-1): mounted filesystem with ordered data mode
EXT4-fs (dm-3): mounted filesystem with ordered data mode
EXT4-fs (dm-0): mounted filesystem with ordered data mode
EXT4-fs (dm-4): mounted filesystem with ordered data mode
Adding 996020k swap on /dev/sda2. Priority:-1 extents:1 across:996020k
Adding 996020k swap on /dev/sdb2. Priority:-2 extents:1 across:996020k
Adding 996020k swap on /dev/sdc2. Priority:-3 extents:1 across:996020k
Adding 996020k swap on /dev/sdd2. Priority:-4 extents:1 across:996020k
\
 
 \ /
  Last update: 2010-04-27 12:03    [W:0.437 / U:0.328 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site