lkml.org 
[lkml]   [2010]   [Mar]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: [PATCH v4 3/3] gpio: add Intel SCH GPIO controller driver
    Hi Denis,

    On Mon, Mar 01, 2010 at 07:02:35PM +0200, Denis Turischev wrote:
    > v2: there is no acpi_check_region, it will be implemented in mfd-core
    > v3: patch refreshed against the latest Linus tree
    > v4: refreshed again
    I'm taking this one as well, unless David NACKs it.

    Cheers,
    Samuel.


    > Signed-off-by: Denis Turischev <denis@compulab.co.il>
    > ---
    > drivers/gpio/Kconfig | 16 +++
    > drivers/gpio/Makefile | 1 +
    > drivers/gpio/sch_gpio.c | 282 +++++++++++++++++++++++++++++++++++++++++++++++
    > 3 files changed, 299 insertions(+), 0 deletions(-)
    > create mode 100644 drivers/gpio/sch_gpio.c
    >
    > diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
    > index 1f1d88a..1730068 100644
    > --- a/drivers/gpio/Kconfig
    > +++ b/drivers/gpio/Kconfig
    > @@ -85,6 +85,22 @@ config GPIO_VR41XX
    > help
    > Say yes here to support the NEC VR4100 series General-purpose I/O Uint
    >
    > +config GPIO_SCH
    > + tristate "Intel SCH GPIO"
    > + depends on GPIOLIB
    > + select LPC_SCH
    > + help
    > + Say yes here to support GPIO interface on Intel Poulsbo SCH.
    > + The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
    > + powered by the core power rail and are turned off during sleep
    > + modes (S3 and higher). The remaining four GPIOs are powered by
    > + the Intel SCH suspend power supply. These GPIOs remain
    > + active during S3. The suspend powered GPIOs can be used to wake the
    > + system from the Suspend-to-RAM state.
    > +
    > + This driver can also be built as a module. If so, the module
    > + will be called sch-gpio.
    > +
    > comment "I2C GPIO expanders:"
    >
    > config GPIO_MAX732X
    > diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
    > index 4868723..aa1d06e 100644
    > --- a/drivers/gpio/Makefile
    > +++ b/drivers/gpio/Makefile
    > @@ -22,3 +22,4 @@ obj-$(CONFIG_GPIO_CS5535) += cs5535-gpio.o
    > obj-$(CONFIG_GPIO_BT8XX) += bt8xxgpio.o
    > obj-$(CONFIG_GPIO_VR41XX) += vr41xx_giu.o
    > obj-$(CONFIG_GPIO_WM831X) += wm831x-gpio.o
    > +obj-$(CONFIG_GPIO_SCH) += sch_gpio.o
    > diff --git a/drivers/gpio/sch_gpio.c b/drivers/gpio/sch_gpio.c
    > new file mode 100644
    > index 0000000..761071a
    > --- /dev/null
    > +++ b/drivers/gpio/sch_gpio.c
    > @@ -0,0 +1,282 @@
    > +/*
    > + * sch_gpio.c - GPIO interface for Intel Poulsbo SCH
    > + *
    > + * Copyright (c) 2010 CompuLab Ltd
    > + * Author: Denis Turischev <denis@compulab.co.il>
    > + *
    > + * This program is free software; you can redistribute it and/or modify
    > + * it under the terms of the GNU General Public License 2 as published
    > + * by the Free Software Foundation.
    > + *
    > + * This program is distributed in the hope that it will be useful,
    > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
    > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
    > + * GNU General Public License for more details.
    > + *
    > + * You should have received a copy of the GNU General Public License
    > + * along with this program; see the file COPYING. If not, write to
    > + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
    > + */
    > +
    > +#include <linux/init.h>
    > +#include <linux/kernel.h>
    > +#include <linux/module.h>
    > +#include <linux/io.h>
    > +#include <linux/errno.h>
    > +#include <linux/acpi.h>
    > +#include <linux/platform_device.h>
    > +
    > +#include <linux/gpio.h>
    > +
    > +static DEFINE_SPINLOCK(gpio_lock);
    > +
    > +#define CGEN (0x00)
    > +#define CGIO (0x04)
    > +#define CGLV (0x08)
    > +
    > +#define RGEN (0x20)
    > +#define RGIO (0x24)
    > +#define RGLV (0x28)
    > +
    > +static unsigned short gpio_ba;
    > +
    > +static int sch_gpio_core_direction_in(struct gpio_chip *gc, unsigned gpio_num)
    > +{
    > + u8 curr_dirs;
    > + unsigned short offset, bit;
    > +
    > + spin_lock(&gpio_lock);
    > +
    > + offset = CGIO + gpio_num / 8;
    > + bit = gpio_num % 8;
    > +
    > + curr_dirs = inb(gpio_ba + offset);
    > +
    > + if (!(curr_dirs & (1 << bit)))
    > + outb(curr_dirs | (1 << bit), gpio_ba + offset);
    > +
    > + spin_unlock(&gpio_lock);
    > + return 0;
    > +}
    > +
    > +static int sch_gpio_core_get(struct gpio_chip *gc, unsigned gpio_num)
    > +{
    > + int res;
    > + unsigned short offset, bit;
    > +
    > + offset = CGLV + gpio_num / 8;
    > + bit = gpio_num % 8;
    > +
    > + res = !!(inb(gpio_ba + offset) & (1 << bit));
    > + return res;
    > +}
    > +
    > +static void sch_gpio_core_set(struct gpio_chip *gc, unsigned gpio_num, int val)
    > +{
    > + u8 curr_vals;
    > + unsigned short offset, bit;
    > +
    > + spin_lock(&gpio_lock);
    > +
    > + offset = CGLV + gpio_num / 8;
    > + bit = gpio_num % 8;
    > +
    > + curr_vals = inb(gpio_ba + offset);
    > +
    > + if (val)
    > + outb(curr_vals | (1 << bit), gpio_ba + offset);
    > + else
    > + outb((curr_vals & ~(1 << bit)), gpio_ba + offset);
    > + spin_unlock(&gpio_lock);
    > +}
    > +
    > +static int sch_gpio_core_direction_out(struct gpio_chip *gc,
    > + unsigned gpio_num, int val)
    > +{
    > + u8 curr_dirs;
    > + unsigned short offset, bit;
    > +
    > + sch_gpio_core_set(gc, gpio_num, val);
    > +
    > + spin_lock(&gpio_lock);
    > +
    > + offset = CGIO + gpio_num / 8;
    > + bit = gpio_num % 8;
    > +
    > + curr_dirs = inb(gpio_ba + offset);
    > + if (curr_dirs & (1 << bit))
    > + outb(curr_dirs & ~(1 << bit), gpio_ba + offset);
    > +
    > + spin_unlock(&gpio_lock);
    > + return 0;
    > +}
    > +
    > +static struct gpio_chip sch_gpio_core = {
    > + .label = "sch_gpio_core",
    > + .owner = THIS_MODULE,
    > + .direction_input = sch_gpio_core_direction_in,
    > + .get = sch_gpio_core_get,
    > + .direction_output = sch_gpio_core_direction_out,
    > + .set = sch_gpio_core_set,
    > +};
    > +
    > +static int sch_gpio_resume_direction_in(struct gpio_chip *gc,
    > + unsigned gpio_num)
    > +{
    > + u8 curr_dirs;
    > +
    > + spin_lock(&gpio_lock);
    > +
    > + curr_dirs = inb(gpio_ba + RGIO);
    > +
    > + if (!(curr_dirs & (1 << gpio_num)))
    > + outb(curr_dirs | (1 << gpio_num) , gpio_ba + RGIO);
    > +
    > + spin_unlock(&gpio_lock);
    > + return 0;
    > +}
    > +
    > +static int sch_gpio_resume_get(struct gpio_chip *gc, unsigned gpio_num)
    > +{
    > + return !!(inb(gpio_ba + RGLV) & (1 << gpio_num));
    > +}
    > +
    > +static void sch_gpio_resume_set(struct gpio_chip *gc,
    > + unsigned gpio_num, int val)
    > +{
    > + u8 curr_vals;
    > +
    > + spin_lock(&gpio_lock);
    > +
    > + curr_vals = inb(gpio_ba + RGLV);
    > +
    > + if (val)
    > + outb(curr_vals | (1 << gpio_num), gpio_ba + RGLV);
    > + else
    > + outb((curr_vals & ~(1 << gpio_num)), gpio_ba + RGLV);
    > +
    > + spin_unlock(&gpio_lock);
    > +}
    > +
    > +static int sch_gpio_resume_direction_out(struct gpio_chip *gc,
    > + unsigned gpio_num, int val)
    > +{
    > + u8 curr_dirs;
    > +
    > + sch_gpio_resume_set(gc, gpio_num, val);
    > +
    > + spin_lock(&gpio_lock);
    > +
    > + curr_dirs = inb(gpio_ba + RGIO);
    > + if (curr_dirs & (1 << gpio_num))
    > + outb(curr_dirs & ~(1 << gpio_num), gpio_ba + RGIO);
    > +
    > + spin_unlock(&gpio_lock);
    > + return 0;
    > +}
    > +
    > +static struct gpio_chip sch_gpio_resume = {
    > + .label = "sch_gpio_resume",
    > + .owner = THIS_MODULE,
    > + .direction_input = sch_gpio_resume_direction_in,
    > + .get = sch_gpio_resume_get,
    > + .direction_output = sch_gpio_resume_direction_out,
    > + .set = sch_gpio_resume_set,
    > +};
    > +
    > +static int __devinit sch_gpio_probe(struct platform_device *pdev)
    > +{
    > + struct resource *res;
    > + int err;
    > +
    > + res = platform_get_resource(pdev, IORESOURCE_IO, 0);
    > + if (!res)
    > + return -EBUSY;
    > +
    > + if (!request_region(res->start, resource_size(res), pdev->name))
    > + return -EBUSY;
    > +
    > + gpio_ba = res->start;
    > +
    > + sch_gpio_core.base = 0;
    > + sch_gpio_core.ngpio = 10;
    > + sch_gpio_core.dev = &pdev->dev;
    > +
    > + sch_gpio_resume.base = 10;
    > + sch_gpio_resume.ngpio = 4;
    > + sch_gpio_resume.dev = &pdev->dev;
    > +
    > + err = gpiochip_add(&sch_gpio_core);
    > + if (err < 0)
    > + goto err_sch_gpio_core;
    > +
    > + err = gpiochip_add(&sch_gpio_resume);
    > + if (err < 0)
    > + goto err_sch_gpio_resume;
    > +
    > + /*
    > + * GPIO[6:0] enabled by default
    > + * GPIO7 is configured by the CMC as SLPIOVR
    > + * Enable GPIO[9:8] core powered gpios explicitly
    > + */
    > + outb(0x3, gpio_ba + CGEN + 1);
    > + /*
    > + * SUS_GPIO[2:0] enabled by default
    > + * Enable SUS_GPIO3 resume powered gpio explicitly
    > + */
    > + outb(0x8, gpio_ba + RGEN);
    > +
    > + return 0;
    > +
    > +err_sch_gpio_resume:
    > + gpiochip_remove(&sch_gpio_core);
    > +
    > +err_sch_gpio_core:
    > + release_region(res->start, resource_size(res));
    > + gpio_ba = 0;
    > +
    > + return err;
    > +}
    > +
    > +static int __devexit sch_gpio_remove(struct platform_device *pdev)
    > +{
    > + struct resource *res;
    > + if (gpio_ba) {
    > + gpiochip_remove(&sch_gpio_core);
    > + gpiochip_remove(&sch_gpio_resume);
    > +
    > + res = platform_get_resource(pdev, IORESOURCE_IO, 0);
    > +
    > + release_region(res->start, resource_size(res));
    > + gpio_ba = 0;
    > + }
    > +
    > + return 0;
    > +}
    > +
    > +static struct platform_driver sch_gpio_driver = {
    > + .driver = {
    > + .name = "sch_gpio",
    > + .owner = THIS_MODULE,
    > + },
    > + .probe = sch_gpio_probe,
    > + .remove = __devexit_p(sch_gpio_remove),
    > +};
    > +
    > +static int __init sch_gpio_init(void)
    > +{
    > + return platform_driver_register(&sch_gpio_driver);
    > +}
    > +
    > +static void __exit sch_gpio_exit(void)
    > +{
    > + platform_driver_unregister(&sch_gpio_driver);
    > +}
    > +
    > +module_init(sch_gpio_init);
    > +module_exit(sch_gpio_exit);
    > +
    > +MODULE_AUTHOR("Denis Turischev <denis@compulab.co.il>");
    > +MODULE_DESCRIPTION("GPIO interface for Intel Poulsbo SCH");
    > +MODULE_LICENSE("GPL");
    > +MODULE_ALIAS("platform:sch_gpio");
    > --
    > 1.6.3.3
    >

    --
    Intel Open Source Technology Centre
    http://oss.intel.com/


    \
     
     \ /
      Last update: 2010-03-02 11:11    [W:2.511 / U:0.084 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site