lkml.org 
[lkml]   [2010]   [Mar]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4/4] Fix typo: orginal => original
Date
Signed-off-by: Thomas Weber <swirl@gmx.li>
---
drivers/ata/ata_piix.c | 2 +-
drivers/gpu/drm/drm_bufs.c | 2 +-
drivers/net/smsc911x.c | 4 ++--
drivers/spi/spi_mpc8xxx.c | 2 +-
drivers/staging/rt2860/rtmp.h | 2 +-
5 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index c338066..b1cb8af 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -43,7 +43,7 @@
* driver the list of errata that are relevant is below, going back to
* PIIX4. Older device documentation is now a bit tricky to find.
*
- * The chipsets all follow very much the same design. The orginal Triton
+ * The chipsets all follow very much the same design. The original Triton
* series chipsets do _not_ support independant device timings, but this
* is fixed in Triton II. With the odd mobile exception the chips then
* change little except in gaining more modes until SATA arrives. This
diff --git a/drivers/gpu/drm/drm_bufs.c b/drivers/gpu/drm/drm_bufs.c
index 8417cc4..8475d58 100644
--- a/drivers/gpu/drm/drm_bufs.c
+++ b/drivers/gpu/drm/drm_bufs.c
@@ -960,7 +960,7 @@ int drm_addbufs_pci(struct drm_device * dev, struct drm_buf_desc * request)
dma->buflist[i + dma->buf_count] = &entry->buflist[i];
}

- /* No allocations failed, so now we can replace the orginal pagelist
+ /* No allocations failed, so now we can replace the original pagelist
* with the new one.
*/
if (dma->page_count) {
diff --git a/drivers/net/smsc911x.c b/drivers/net/smsc911x.c
index 4fd1d8b..eb17598 100644
--- a/drivers/net/smsc911x.c
+++ b/drivers/net/smsc911x.c
@@ -737,7 +737,7 @@ static void smsc911x_phy_adjust_link(struct net_device *dev)
SMSC_TRACE(HW, "configuring for carrier OK");
if ((pdata->gpio_orig_setting & GPIO_CFG_LED1_EN_) &&
(!pdata->using_extphy)) {
- /* Restore orginal GPIO configuration */
+ /* Restore original GPIO configuration */
pdata->gpio_setting = pdata->gpio_orig_setting;
smsc911x_reg_write(pdata, GPIO_CFG,
pdata->gpio_setting);
@@ -751,7 +751,7 @@ static void smsc911x_phy_adjust_link(struct net_device *dev)
if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_) &&
(!pdata->using_extphy)) {
/* Force 10/100 LED off, after saving
- * orginal GPIO configuration */
+ * original GPIO configuration */
pdata->gpio_orig_setting = pdata->gpio_setting;

pdata->gpio_setting &= ~GPIO_CFG_LED1_EN_;
diff --git a/drivers/spi/spi_mpc8xxx.c b/drivers/spi/spi_mpc8xxx.c
index 4f0cc9d..56efdfe 100644
--- a/drivers/spi/spi_mpc8xxx.c
+++ b/drivers/spi/spi_mpc8xxx.c
@@ -639,7 +639,7 @@ static int mpc8xxx_spi_setup(struct spi_device *spi)
}
mpc8xxx_spi = spi_master_get_devdata(spi->master);

- hw_mode = cs->hw_mode; /* Save orginal settings */
+ hw_mode = cs->hw_mode; /* Save original settings */
cs->hw_mode = mpc8xxx_spi_read_reg(&mpc8xxx_spi->base->mode);
/* mask out bits we are going to set */
cs->hw_mode &= ~(SPMODE_CP_BEGIN_EDGECLK | SPMODE_CI_INACTIVEHIGH
diff --git a/drivers/staging/rt2860/rtmp.h b/drivers/staging/rt2860/rtmp.h
index 4401a55..9224dc4 100644
--- a/drivers/staging/rt2860/rtmp.h
+++ b/drivers/staging/rt2860/rtmp.h
@@ -346,7 +346,7 @@ struct rt_rtmp_sg_list {
#define LEAP_ON(_p) (((_p)->StaCfg.LeapAuthMode) == CISCO_AuthModeLEAP)
#define LEAP_CCKM_ON(_p) ((((_p)->StaCfg.LeapAuthMode) == CISCO_AuthModeLEAP) && ((_p)->StaCfg.LeapAuthInfo.CCKM == TRUE))

-/* if orginal Ethernet frame contains no LLC/SNAP, then an extra LLC/SNAP encap is required */
+/* if original Ethernet frame contains no LLC/SNAP, then an extra LLC/SNAP encap is required */
#define EXTRA_LLCSNAP_ENCAP_FROM_PKT_START(_pBufVA, _pExtraLlcSnapEncap) \
{ \
if (((*(_pBufVA + 12) << 8) + *(_pBufVA + 13)) > 1500) \
--
1.6.4.4


\
 
 \ /
  Last update: 2010-03-15 22:01    [W:0.043 / U:1.464 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site