lkml.org 
[lkml]   [2010]   [Dec]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [linux-pm] 2.6.37-rc5, pata_atiixp, DVD-ROM: kernel log flooded with "rpm_resume flags 0x4", "rpm_resume returns 1"
On Dec 11 Alan Stern wrote:
> On Sat, 11 Dec 2010, Stefan Richter wrote:
>
> > Hi,
> >
> > I just booted from 2.6.36 (without PM debugging configured) into
> > 2.6.37-rc5 (with PM debugging enabled). There is endless log spam like
> > this:
> >
> > Dec 11 17:11:31 stein kernel: scsi host6: rpm_resume flags 0x4
> > Dec 11 17:11:31 stein kernel: scsi host6: rpm_resume returns 1
> > Dec 11 17:11:31 stein kernel: scsi host6: rpm_resume flags 0x4
> > Dec 11 17:11:31 stein kernel: scsi host6: rpm_resume returns 1
> ...
>
> > Why is rpm_resume performed 6 times every two seconds?
>
> This is probably because hal probes the DVD drive every two seconds
> looking for media changes. However that's not supposed to cause
> rpm_resume to be called for the host unless runtime PM is allowed for
> the DVD drive, which it isn't according to your listings below. So
> there's a bug somewhere.

I had 2.6.36 running since then and have now booted into 2.6.37-rc6.

Yes, it is hal indeed. Shutting hal down avoids this logging activity.

> > host6 is pata_atiixp with an:
> >
> > 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller
> > (prog-if 8a [Master SecP PriP])
> >
> > # grep . /sys/class/scsi_host/host6/power/*
> > /sys/class/scsi_host/host6/power/async:enabled
> > grep: /sys/class/scsi_host/host6/power/autosuspend_delay_ms: Input/output error
> > /sys/class/scsi_host/host6/power/control:auto
> > /sys/class/scsi_host/host6/power/runtime_active_kids:0
> > /sys/class/scsi_host/host6/power/runtime_active_time:0
> > /sys/class/scsi_host/host6/power/runtime_enabled:disabled
> > /sys/class/scsi_host/host6/power/runtime_status:unsupported
> > /sys/class/scsi_host/host6/power/runtime_suspended_time:0
> > /sys/class/scsi_host/host6/power/runtime_usage:0
>
> This is the wrong directory (the class device, not the device itself).
> You should look at /sys/class/scsi_host/host6/device/power instead.
> And also /sys/class/scsi_host/host6/device/target6:0:0/power.

OK, correct directory follows below.

Actually, this time I see once every two seconds a message about
logical unit 6:0:0:0 and 6 times every two seconds a message about
host7:

Dec 17 20:22:08 stein kernel: sd 6:0:0:0: rpm_resume flags 0x4
Dec 17 20:22:08 stein kernel: sd 6:0:0:0: rpm_resume returns 1
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:10 stein kernel: sd 6:0:0:0: rpm_resume flags 0x4
Dec 17 20:22:10 stein kernel: sd 6:0:0:0: rpm_resume returns 1
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4
Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1

sd 6:0:0:0 is a USB card reader built into a monitor:
Host: scsi6 Channel: 00 Id: 00 Lun: 00
Vendor: Generic Model: Ultra HS-SD/MMC Rev: 1.88
Type: Direct-Access ANSI SCSI revision: 00

This is from the power/ directory of the "6:0:0:0" device which is
bound to driver sd:

/sys/devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/host6/target6:0:0/6:0:0:0/power/async:enabled
/sys/devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/host6/target6:0:0/6:0:0:0/power/control:on
/sys/devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/host6/target6:0:0/6:0:0:0/power/runtime_active_kids:0
/sys/devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/host6/target6:0:0/6:0:0:0/power/runtime_active_time:1650131
/sys/devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/host6/target6:0:0/6:0:0:0/power/runtime_enabled:forbidden
/sys/devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/host6/target6:0:0/6:0:0:0/power/runtime_status:active
/sys/devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/host6/target6:0:0/6:0:0:0/power/runtime_suspended_time:0
/sys/devices/pci0000:00/0000:00:12.2/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/host6/target6:0:0/6:0:0:0/power/runtime_usage:1

host7 is the mentioned ATI SB700/SB800 IDE controller. Here is the
power/ directory of the scsi_host device (rather than scsi_host class
device):

/sys/devices/pci0000:00/0000:00:14.1/host7/power/async:enabled
/sys/devices/pci0000:00/0000:00:14.1/host7/power/control:auto
/sys/devices/pci0000:00/0000:00:14.1/host7/power/runtime_active_kids:1
/sys/devices/pci0000:00/0000:00:14.1/host7/power/runtime_active_time:1935478
/sys/devices/pci0000:00/0000:00:14.1/host7/power/runtime_enabled:enabled
/sys/devices/pci0000:00/0000:00:14.1/host7/power/runtime_status:active
/sys/devices/pci0000:00/0000:00:14.1/host7/power/runtime_suspended_time:0
/sys/devices/pci0000:00/0000:00:14.1/host7/power/runtime_usage:0

The parent device 0000:00:14.1 is bound to the mentioned pata_atiixp,
if this is of any importance at all.

From the child device:

/sys/devices/pci0000:00/0000:00:14.1/host7/target7:0:0/power/async:enabled
/sys/devices/pci0000:00/0000:00:14.1/host7/target7:0:0/power/control:auto
/sys/devices/pci0000:00/0000:00:14.1/host7/target7:0:0/power/runtime_active_kids:1
/sys/devices/pci0000:00/0000:00:14.1/host7/target7:0:0/power/runtime_active_time:2402125
/sys/devices/pci0000:00/0000:00:14.1/host7/target7:0:0/power/runtime_enabled:enabled
/sys/devices/pci0000:00/0000:00:14.1/host7/target7:0:0/power/runtime_status:active
/sys/devices/pci0000:00/0000:00:14.1/host7/target7:0:0/power/runtime_suspended_time:0
/sys/devices/pci0000:00/0000:00:14.1/host7/target7:0:0/power/runtime_usage:0

--------

On Dec 11 Rafael J. Wysocki wrote:
> On Saturday, December 11, 2010, Stefan Richter wrote:
> > Hi,
> >
> > I just booted from 2.6.36 (without PM debugging configured) into
> > 2.6.37-rc5 (with PM debugging enabled). There is endless log spam like
> > this:
>
> I guess you have either CONFIG_PM_VERBOSE set or CONFIG_PM_DEBUG unset.
>
> Which is the case?

I have both options off on 2.6.36 and older kernels. I have both
options on on 2.6.37-rc5/-rc6 (because I wanted to check something
unrelated on 2.6.37).
--
Stefan Richter
-=====-==-=- ==-- =---=
http://arcgraph.de/sr/


\
 
 \ /
  Last update: 2010-12-17 21:19    [W:0.071 / U:0.704 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site