lkml.org 
[lkml]   [2010]   [Nov]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH 01/07] ARM: Introduce asm/hardware/entry-macro-gic.S
From: Magnus Damm <damm@opensource.se>

This patch is the identical GIC demux implementation
merge V3. Instead of implementing same code over and
over simply share it in entry-macro-gic.S. The shared
code is based on the realview implementation.

Each GIC demux instance still has to setup the base address
of the controller using the get_irqnr_preamble macro. The
rest of the GIC specific code can be shared.

Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Srinidhi Kasagar<srinidhi.kasagar@stericsson.com>
---

Changes since V2:
- broke out patches into base + per sub-arch

arch/arm/include/asm/hardware/entry-macro-gic.S | 68 +++++++++++++++++++++++
1 file changed, 68 insertions(+)

--- /dev/null
+++ work/arch/arm/include/asm/hardware/entry-macro-gic.S 2010-11-12 15:57:05.000000000 +0900
@@ -0,0 +1,68 @@
+/*
+ * arch/arm/include/asm/hardware/entry-macro-gic.S
+ *
+ * Low-level IRQ helper macros for GIC
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <asm/hardware/gic.h>
+
+/*
+ * The interrupt numbering scheme is defined in the
+ * interrupt controller spec. To wit:
+ *
+ * Interrupts 0-15 are IPI
+ * 16-28 are reserved
+ * 29-31 are local. We allow 30 to be used for the watchdog.
+ * 32-1020 are global
+ * 1021-1022 are reserved
+ * 1023 is "spurious" (no interrupt)
+ *
+ * For now, we ignore all local interrupts so only return an interrupt if it's
+ * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs.
+ *
+ * A simple read from the controller will tell us the number of the highest
+ * priority enabled interrupt. We then just need to check whether it is in the
+ * valid range for an IRQ (30-1020 inclusive).
+ */
+
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+ ldr \irqstat, [\base, #GIC_CPU_INTACK]
+ /* bits 12-10 = src CPU, 9-0 = int # */
+
+ ldr \tmp, =1021
+ bic \irqnr, \irqstat, #0x1c00
+ cmp \irqnr, #29
+ cmpcc \irqnr, \irqnr
+ cmpne \irqnr, \tmp
+ cmpcs \irqnr, \irqnr
+ .endm
+
+/* We assume that irqstat (the raw value of the IRQ acknowledge
+ * register) is preserved from the macro above.
+ * If there is an IPI, we immediately signal end of interrupt on the
+ * controller, since this requires the original irqstat value which
+ * we won't easily be able to recreate later.
+ */
+
+ .macro test_for_ipi, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ cmp \irqnr, #16
+ strcc \irqstat, [\base, #GIC_CPU_EOI]
+ cmpcs \irqnr, \irqnr
+ .endm
+
+/* As above, this assumes that irqstat and base are preserved.. */
+
+ .macro test_for_ltirq, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ mov \tmp, #0
+ cmp \irqnr, #29
+ moveq \tmp, #1
+ streq \irqstat, [\base, #GIC_CPU_EOI]
+ cmp \tmp, #0
+ .endm

\
 
 \ /
  Last update: 2010-11-12 09:21    [W:0.435 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site