lkml.org 
[lkml]   [2010]   [Jan]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: BAR 0: can't allocate resource
Date
> You mentioned two messages.  Here's the first:
> PCI: BIOS Bug: MCFG area at e0000000 is not reserved in ACPI motherboard
> resources PCI: Not using MMCONFIG.
>
> and the second:
> PCI: Cannot allocate resource region 0 of device 0000:01:04.0
> PCI: Error while updating region 0000:01:04.0/0 (feb00002 != 00000000)
>
> The "Error while updating region" message is because we wrote something
> to a BAR, read it back, and they didn't match. I suppose this could be
> some kind of config space problem related to the fact that we're not
> using MMCONFIG.
>
> Can you try removing the MCFG reservation check, so we do try to use
> MMCONFIG? If you do this on a current kernel, we'll also get a little
> more debug output about the subsequent resource allocation failure.

I did this on my 2.6.26 kernel (is this current enough or would a later kernel
be better?) and attached the dmesg output.

Alex
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-custom (2.6.26) (root@moss) (gcc version 4.3.3 (Debian 4.3.3-3) ) #1 SMP Thu Jan 7 11:23:54 EST 2010
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f7c0000 (usable)
[ 0.000000] BIOS-e820: 000000003f7c0000 - 000000003f7ce000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003f7ce000 - 000000003f800000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] 119MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 0.000000] Entering add_active_range(0, 0, 260032) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 260032
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 260032
[ 0.000000] On node 0 totalpages: 260032
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 240 pages used for memmap
[ 0.000000] HighMem zone: 30416 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F8ED0, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 3F7C0000, 003C (r1 112007 RSDT1407 20071120 MSFT 97)
[ 0.000000] ACPI: FACP 3F7C0200, 0084 (r2 112007 FACP1407 20071120 MSFT 97)
[ 0.000000] ACPI: DSDT 3F7C05B0, 4FF8 (r1 DLAG_ DLAG_117 117 INTL 20051117)
[ 0.000000] ACPI: FACS 3F7CE000, 0040
[ 0.000000] ACPI: APIC 3F7C0390, 005C (r1 112007 APIC1407 20071120 MSFT 97)
[ 0.000000] ACPI: MCFG 3F7C03F0, 003C (r1 112007 OEMMCFG 20071120 MSFT 97)
[ 0.000000] ACPI: SLIC 3F7C0430, 0176 (r1 112007 SLIC1407 20071120 MSFT 97)
[ 0.000000] ACPI: OEMB 3F7CE040, 0071 (r1 112007 OEMB1407 20071120 MSFT 97)
[ 0.000000] ACPI: ASF! 3F7C55B0, 0075 (r32 LEGEND I865PASF 1 INTL 20051117)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3f800000:bf600000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37576 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258000
[ 0.000000] Kernel command line: root=/dev/hdb2 ro 8250.nr_uarts=10 quiet
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1666.687 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 1021624k/1040128k available (1791k kernel code, 17740k reserved, 725k data, 248k init, 122624k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc037d000 - 0xc03bb000 ( 248 kB)
[ 0.004000] .data : 0xc02bfd70 - 0xc0375418 ( 725 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02bfd70 (1791 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084101] Calibrating delay using timer specific routine.. 3337.10 BogoMIPS (lpj=6674206)
[ 0.084138] Security Framework initialized
[ 0.084144] SELinux: Disabled at boot.
[ 0.084148] Capability LSM initialized
[ 0.084163] Mount-cache hash table entries: 512
[ 0.084302] Initializing cgroup subsys ns
[ 0.084306] Initializing cgroup subsys cpuacct
[ 0.084309] Initializing cgroup subsys devices
[ 0.084328] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084331] CPU: L2 cache: 2048K
[ 0.084335] Intel machine check architecture supported.
[ 0.084341] Intel machine check reporting enabled on CPU#0.
[ 0.084343] using mwait in idle threads.
[ 0.084352] Checking 'hlt' instruction... OK.
[ 0.100449] SMP alternatives: switching to UP code
[ 0.106103] ACPI: Core revision 20080321
[ 0.120007] ENABLING IO-APIC IRQs
[ 0.120007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.159715] CPU0: Intel(R) Core(TM) Duo CPU L2400 @ 1.66GHz stepping 0c
[ 0.160010] Brought up 1 CPUs
[ 0.160010] Total of 1 processors activated (3337.10 BogoMIPS).
[ 0.160010] CPU0 attaching sched-domain:
[ 0.160010] domain 0: span 0
[ 0.160010] groups: 0
[ 0.160010] net_namespace: 660 bytes
[ 0.160010] Booting paravirtualized kernel on bare hardware
[ 0.160010] NET: Registered protocol family 16
[ 0.160010] ACPI: bus type pci registered
[ 0.160010] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.160010] PCI: Not using MMCONFIG.
[ 0.160010] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=1
[ 0.160010] PCI: Using configuration type 1 for base access
[ 0.160010] Setting up standard PCI resources
[ 0.168010] ACPI: EC: Look up EC in DSDT
[ 0.178108] ACPI: Interpreter enabled
[ 0.178111] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.178128] ACPI: Using IOAPIC for interrupt routing
[ 0.178193] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.185680] AlexB: ignoring error and continuing: PCI: BIOS Bug: MCFG area at e0000000 is not reserved in ACPI motherboard resources
[ 0.185684] PCI: Using MMCONFIG for extended config space
[ 0.196164] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.196841] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.196847] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[ 0.196852] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[ 0.197225] PCI: Transparent bridge - 0000:00:1e.0
[ 0.197248] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.197507] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.207695] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.207842] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.207989] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.208139] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.208284] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.208428] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.208576] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.208724] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12 14 15)
[ 0.208942] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 48, should be 41 [20080321]
[ 0.208966] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.208997] pnp: PnP ACPI init
[ 0.209005] ACPI: bus type pnp registered
[ 0.215537] pnp: PnP ACPI: found 17 devices
[ 0.215540] ACPI: ACPI bus type pnp unregistered
[ 0.215543] PnPBIOS: Disabled by ACPI PNP
[ 0.215788] PCI: Using ACPI for IRQ routing
[ 0.215844] PCI: Cannot allocate resource region 0 of device 0000:01:04.0
[ 0.216114] hpet clockevent registered
[ 0.216120] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.216125] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.217165] ACPI: RTC can wake from S4
[ 0.217190] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[ 0.217200] system 00:09: ioport range 0xa00-0xa0f has been reserved
[ 0.217209] system 00:0b: ioport range 0x4d0-0x4d1 has been reserved
[ 0.217213] system 00:0b: ioport range 0x800-0x87f has been reserved
[ 0.217216] system 00:0b: ioport range 0x480-0x4bf has been reserved
[ 0.217220] system 00:0b: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.217223] system 00:0b: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.217226] system 00:0b: iomem range 0xfed40000-0xfed8ffff has been reserved
[ 0.217233] system 00:0d: iomem range 0xffc00000-0xffefffff could not be reserved
[ 0.217239] system 00:0e: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.217242] system 00:0e: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 0.217248] system 00:0f: iomem range 0xe0000000-0xe3ffffff has been reserved
[ 0.217254] system 00:10: iomem range 0x0-0x9ffff could not be reserved
[ 0.217257] system 00:10: iomem range 0xc0000-0xcffff could not be reserved
[ 0.217260] system 00:10: iomem range 0xe0000-0xfffff could not be reserved
[ 0.217263] system 00:10: iomem range 0x100000-0x3f7fffff could not be reserved
[ 0.217266] system 00:10: iomem range 0xfed90000-0xffffffff could not be reserved
[ 0.247644] PCI: Error while updating region 0000:01:04.0/0 (feb00002 != 00000000)
[ 0.247698] PCI: Bridge: 0000:00:1e.0
[ 0.247702] IO window: e000-efff
[ 0.247707] MEM window: 0xfeb00000-0xfebfffff
[ 0.247711] PREFETCH window: disabled.
[ 0.247728] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.247748] NET: Registered protocol family 2
[ 0.247837] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.248071] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.248862] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.249261] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.249264] TCP reno registered
[ 0.249374] NET: Registered protocol family 1
[ 0.249488] checking if image is initramfs... it is
[ 0.720023] Switched to high resolution mode on CPU 0
[ 0.749105] Freeing initrd memory: 5482k freed
[ 0.749850] audit: initializing netlink socket (disabled)
[ 0.749866] type=2000 audit(1262826245.748:1): initialized
[ 0.750020] highmem bounce pool size: 64 pages
[ 0.750025] Total HugeTLB memory allocated, 0
[ 0.750099] VFS: Disk quotas dquot_6.5.1
[ 0.750124] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.750170] msgmni has been set to 1767
[ 0.750267] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.750270] io scheduler noop registered
[ 0.750272] io scheduler anticipatory registered
[ 0.750275] io scheduler deadline registered
[ 0.750285] io scheduler cfq registered (default)
[ 0.750300] pci 0000:00:02.0: Boot video device
[ 0.750397] pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
[ 0.750712] isapnp: Scanning for PnP cards...
[ 1.105027] isapnp: No Plug & Play device found
[ 1.107558] Serial: 8250/16550 driver $Revision: 1.90 $ 10 ports, IRQ sharing enabled
[ 1.107690] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.107815] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.108453] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.108633] 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.110043] brd: module loaded
[ 1.110192] PNP: No PS/2 controller found. Probing ports directly.
[ 1.112371] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.112377] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.112515] mice: PS/2 mouse device common for all mice
[ 1.112636] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.112657] rtc0: alarms up to one month
[ 1.112691] cpuidle: using governor ladder
[ 1.112694] cpuidle: using governor menu
[ 1.112698] No iBFT detected.
[ 1.113076] TCP cubic registered
[ 1.113079] NET: Registered protocol family 17
[ 1.113085] Using IPI No-Shortcut mode
[ 1.113193] registered taskstats version 1
[ 1.113324] rtc_cmos 00:03: setting system clock to 2010-01-07 01:04:07 UTC (1262826247)
[ 1.113454] Freeing unused kernel memory: 248k freed
[ 1.187611] ACPI: SSDT 3F7CE0C0, 0688 (r1 AMI CPU1PM 1 INTL 20051117)
[ 1.188254] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 1.188298] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.635732] usbcore: registered new interface driver usbfs
[ 1.635759] usbcore: registered new interface driver hub
[ 1.635789] usbcore: registered new device driver usb
[ 1.644059] USB Universal Host Controller Interface driver v3.0
[ 1.644106] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 1.644119] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 1.644123] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.644249] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 1.644283] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000dc00
[ 1.644369] usb usb1: configuration #1 chosen from 1 choice
[ 1.644400] hub 1-0:1.0: USB hub found
[ 1.644406] hub 1-0:1.0: 2 ports detected
[ 1.735791] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 1.735794] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.746826] No dock devices found.
[ 1.754725] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.754728] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.754731] usb usb1: Product: UHCI Host Controller
[ 1.754734] usb usb1: Manufacturer: Linux 2.6.26-custom uhci_hcd
[ 1.754736] usb usb1: SerialNumber: 0000:00:1d.0
[ 1.754808] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 1.754818] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 1.754823] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.754847] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 1.754880] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880
[ 1.754955] usb usb2: configuration #1 chosen from 1 choice
[ 1.754983] hub 2-0:1.0: USB hub found
[ 1.754990] hub 2-0:1.0: 2 ports detected
[ 1.770625] SCSI subsystem initialized
[ 1.784134] libata version 3.00 loaded.
[ 1.856106] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.856110] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.856113] usb usb2: Product: UHCI Host Controller
[ 1.856115] usb usb2: Manufacturer: Linux 2.6.26-custom uhci_hcd
[ 1.856118] usb usb2: SerialNumber: 0000:00:1d.1
[ 1.856176] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 1.856187] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 1.856191] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.856216] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 1.856250] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
[ 1.856326] usb usb3: configuration #1 chosen from 1 choice
[ 1.856354] hub 3-0:1.0: USB hub found
[ 1.856360] hub 3-0:1.0: 2 ports detected
[ 1.940002] Marking TSC unstable due to: TSC halts in idle.
[ 1.963998] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.964002] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.964005] usb usb3: Product: UHCI Host Controller
[ 1.964007] usb usb3: Manufacturer: Linux 2.6.26-custom uhci_hcd
[ 1.964009] usb usb3: SerialNumber: 0000:00:1d.2
[ 1.964014] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[ 1.964014] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 1.964014] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.964014] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 1.964014] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d480
[ 1.964014] usb usb4: configuration #1 chosen from 1 choice
[ 1.964014] hub 4-0:1.0: USB hub found
[ 1.964014] hub 4-0:1.0: 2 ports detected
[ 1.994949] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 2.066799] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.066802] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.066805] usb usb4: Product: UHCI Host Controller
[ 2.066807] usb usb4: Manufacturer: Linux 2.6.26-custom uhci_hcd
[ 2.066809] usb usb4: SerialNumber: 0000:00:1d.3
[ 2.066961] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.066976] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.066980] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.067003] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 2.070923] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.070930] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.070935] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfea37c00
[ 2.128023] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.128078] usb usb5: configuration #1 chosen from 1 choice
[ 2.128104] hub 5-0:1.0: USB hub found
[ 2.128112] hub 5-0:1.0: 8 ports detected
[ 2.232095] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.232098] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.232101] usb usb5: Product: EHCI Host Controller
[ 2.232103] usb usb5: Manufacturer: Linux 2.6.26-custom ehci_hcd
[ 2.232105] usb usb5: SerialNumber: 0000:00:1d.7
[ 2.233214] ACPI: PCI Interrupt 0000:01:08.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 2.258614] e100: eth0: e100_probe: addr 0xfebfe000, irq 20, MAC addr 00:30:59:04:25:2e
[ 2.258657] ata_piix 0000:00:1f.2: version 2.12
[ 2.258674] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 2.258679] ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ]
[ 2.258714] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.258771] scsi0 : ata_piix
[ 2.258853] scsi1 : ata_piix
[ 2.258884] ata1: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xcc00 irq 19
[ 2.258887] ata2: SATA max UDMA/133 cmd 0xd000 ctl 0xcc80 bmdma 0xcc08 irq 19
[ 2.524197] usb 1-1: device not accepting address 2, error -71
[ 2.594897] Uniform Multi-Platform E-IDE driver
[ 2.594901] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 2.595366] ICH7: IDE controller (0x8086:0x27df rev 0x02) at PCI slot 0000:00:1f.1
[ 2.595377] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 2.595386] ICH7: not 100% native mode: will probe irqs later
[ 2.595394] ICH7: IDE port disabled
[ 2.595399] ide0: BM-DMA at 0xffa0-0xffa7
[ 2.595404] Probing IDE interface ide0...
[ 2.606275] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 3.104285] hdb: SILICONSYSTEMS UDMA 4GB-4300, ATA DISK drive
[ 3.120023] usb 1-1: new low speed USB device using uhci_hcd and address 4
[ 3.160055] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 3.160101] hdb: host side 80-wire cable detection failed, limiting max speed to UDMA33
[ 3.160103] hdb: UDMA/33 mode selected
[ 3.160152] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 3.177696] hdb: max request size: 128KiB
[ 3.177699] hdb: 8027712 sectors (4110 MB) w/1KiB Cache, CHS=7964/16/63
[ 3.177959] hdb: cache flushes supported
[ 3.177990] hdb: hdb1 hdb2 hdb3 < hdb5 hdb6 hdb7 hdb8 hdb9 >
[ 3.265510] PM: Starting manual resume from disk
[ 3.277632] kjournald starting. Commit interval 5 seconds
[ 3.277641] EXT3-fs: mounted filesystem with ordered data mode.
[ 3.371382] usb 1-1: configuration #1 chosen from 1 choice
[ 3.377453] usb 1-1: New USB device found, idVendor=1241, idProduct=1603
[ 3.377457] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.377460] usb 1-1: Product: USB Keyboard
[ 3.377461] usb 1-1: Manufacturer:
[ 3.623882] udevd version 125 started
[ 4.179487] Linux agpgart interface v0.103
[ 4.184696] agpgart: Detected an Intel 945GME Chipset.
[ 4.185040] agpgart: Detected 7932K stolen memory.
[ 4.200169] agpgart: AGP aperture is 256M @ 0xd0000000
[ 4.340024] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 4.340046] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 4.375731] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
[ 4.425641] usbcore: registered new interface driver hiddev
[ 4.459370] input: Power Button (FF) as /class/input/input0
[ 4.469725] input: USB Keyboard as /class/input/input1
[ 4.473389] ACPI: Power Button (FF) [PWRF]
[ 4.473472] input: Power Button (CM) as /class/input/input2
[ 4.491042] ACPI: Power Button (CM) [PWRB]
[ 4.504057] input,hidraw0: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.0-1
[ 4.589402] input: USB Keyboard as /class/input/input3
[ 4.600039] input,hidraw1: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.0-1
[ 4.600059] usbcore: registered new interface driver usbhid
[ 4.600064] usbhid: v2.6:USB HID core driver
[ 5.597656] intel_rng: FWH not detected
[ 5.620584] input: Video Bus as /class/input/input4
[ 5.632023] ACPI: Video Device [IGD] (multi-head: yes rom: no post: no)
[ 5.679083] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 5.679151] iTCO_wdt: Found a ICH7-M DH TCO device (Version=2, TCOBASE=0x0860)
[ 5.679181] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 5.791951] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
[ 5.859236] input: PC Speaker as /class/input/input5
[ 5.876135] Error: Driver 'pcspkr' is already registered, aborting...
[ 5.962974] Error: Driver 'pcspkr' is already registered, aborting...
[ 6.133435] parport_pc 00:08: reported by Plug and Play ACPI
[ 6.133487] parport0: PC-style at 0x378, irq 7 [PCSPP]
[ 6.974296] Adding 489940k swap on /dev/hdb8. Priority:-1 extents:1 across:489940k
[ 7.879067] loop: module loaded
[ 7.892565] ppdev: user-space parallel port driver
[ 8.258340] kjournald starting. Commit interval 5 seconds
[ 8.258349] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.259734] kjournald starting. Commit interval 5 seconds
[ 8.282598] EXT3 FS on hdb6, internal journal
[ 8.282598] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.283201] kjournald starting. Commit interval 5 seconds
[ 8.414148] EXT3 FS on hdb7, internal journal
[ 8.414148] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.415383] kjournald starting. Commit interval 5 seconds
[ 8.415383] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.416843] kjournald starting. Commit interval 5 seconds
[ 8.434804] EXT3 FS on hdb5, internal journal
[ 8.434804] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.636130] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 12.763934] NET: Registered protocol family 10
[ 12.764326] lo: Disabled Privacy Extensions
[ 23.596026] eth0: no IPv6 routers present
\
 
 \ /
  Last update: 2010-01-07 02:13    [W:0.080 / U:0.208 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site