lkml.org 
[lkml]   [2010]   [Jan]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH 55/68] it821x: convert to ide2libata
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Subject: [PATCH] it821x: convert to ide2libata

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ata/pata_it821x.h | 21 ++
drivers/ide/it821x.c | 373 ----------------------------------------------
2 files changed, 28 insertions(+), 366 deletions(-)

Index: b/drivers/ata/pata_it821x.h
===================================================================
--- a/drivers/ata/pata_it821x.h
+++ b/drivers/ata/pata_it821x.h
@@ -55,7 +55,11 @@ struct it821x_dev {
u16 pio[2]; /* Cached PIO values */
u16 mwdma[2]; /* Cached MWDMA values */
u16 udma[2]; /* Cached UDMA values (per drive) */
+#ifndef __IDE2LIBATA
u16 last_device; /* Master or slave loaded ? */
+#else
+ u16 quirks;
+#endif
};

#define ATA_66 0
@@ -223,7 +227,21 @@ static void it821x_passthru_set_piomode(
struct it821x_dev *itdev = ap->private_data;
int unit = adev->devno;
int mode_wanted = adev->pio_mode - XFER_PIO_0;
+#ifdef __IDE2LIBATA
+ struct ata_device *pair = ata_dev_pair(adev);

+ /*
+ * Compute the best PIO mode we can for a given device. We must
+ * pick a speed that does not cause problems with the other device
+ * on the cable.
+ */
+ if (pair) {
+ u8 pair_pio = pair->pio_mode - XFER_PIO_0;
+ /* trim PIO to the slowest of the master/slave */
+ if (pair_pio < mode_wanted)
+ mode_wanted = pair_pio;
+ }
+#endif
/* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
itdev->want[unit][1] = pio_want[mode_wanted];
itdev->want[unit][0] = 1; /* PIO is lowest priority */
@@ -297,11 +315,12 @@ static void it821x_passthru_set_dmamode(

static void it821x_disable_raid(struct pci_dev *pdev)
{
+#ifndef __IDE2LIBATA
/* Neither the RDC nor the IT8211 */
if (pdev->vendor != PCI_VENDOR_ID_ITE ||
pdev->device != PCI_DEVICE_ID_ITE_8212)
return;
-
+#endif
/* Reset local CPU, and set BIOS not ready */
pci_write_config_byte(pdev, 0x5E, 0x01);

Index: b/drivers/ide/it821x.c
===================================================================
--- a/drivers/ide/it821x.c
+++ b/drivers/ide/it821x.c
@@ -8,51 +8,6 @@
* Documentation:
* Datasheet is freely available, some other documents under NDA.
*
- * The ITE8212 isn't exactly a standard IDE controller. It has two
- * modes. In pass through mode then it is an IDE controller. In its smart
- * mode its actually quite a capable hardware raid controller disguised
- * as an IDE controller. Smart mode only understands DMA read/write and
- * identify, none of the fancier commands apply. The IT8211 is identical
- * in other respects but lacks the raid mode.
- *
- * Errata:
- * o Rev 0x10 also requires master/slave hold the same DMA timings and
- * cannot do ATAPI MWDMA.
- * o The identify data for raid volumes lacks CHS info (technically ok)
- * but also fails to set the LBA28 and other bits. We fix these in
- * the IDE probe quirk code.
- * o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
- * raid then the controller firmware dies
- * o Smart mode without RAID doesn't clear all the necessary identify
- * bits to reduce the command set to the one used
- *
- * This has a few impacts on the driver
- * - In pass through mode we do all the work you would expect
- * - In smart mode the clocking set up is done by the controller generally
- * but we must watch the other limits and filter.
- * - There are a few extra vendor commands that actually talk to the
- * controller but only work PIO with no IRQ.
- *
- * Vendor areas of the identify block in smart mode are used for the
- * timing and policy set up. Each HDD in raid mode also has a serial
- * block on the disk. The hardware extra commands are get/set chip status,
- * rebuild, get rebuild status.
- *
- * In Linux the driver supports pass through mode as if the device was
- * just another IDE controller. If the smart mode is running then
- * volumes are managed by the controller firmware and each IDE "disk"
- * is a raid volume. Even more cute - the controller can do automated
- * hotplug and rebuild.
- *
- * The pass through controller itself is a little demented. It has a
- * flaw that it has a single set of PIO/MWDMA timings per channel so
- * non UDMA devices restrict each others performance. It also has a
- * single clock source per channel so mixed UDMA100/133 performance
- * isn't perfect and we have to pick a clock. Thankfully none of this
- * matters in smart mode. ATAPI DMA is not currently supported.
- *
- * It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
- *
* TODO
* - ATAPI UDMA is ok but not MWDMA it seems
* - RAID configuration ioctls
@@ -69,280 +24,8 @@

#define QUIRK_VORTEX86 1

-struct it821x_dev
-{
- unsigned int smart:1, /* Are we in smart raid mode */
- timing10:1; /* Rev 0x10 */
- u8 clock_mode; /* 0, ATA_50 or ATA_66 */
- u8 want[2][2]; /* Mode/Pri log for master slave */
- /* We need these for switching the clock when DMA goes on/off
- The high byte is the 66Mhz timing */
- u16 pio[2]; /* Cached PIO values */
- u16 mwdma[2]; /* Cached MWDMA values */
- u16 udma[2]; /* Cached UDMA values (per drive) */
- u16 quirks;
-};
-
-#define ATA_66 0
-#define ATA_50 1
-#define ATA_ANY 2
-
-#define UDMA_OFF 0
-#define MWDMA_OFF 0
-
-/*
- * We allow users to force the card into non raid mode without
- * flashing the alternative BIOS. This is also necessary right now
- * for embedded platforms that cannot run a PC BIOS but are using this
- * device.
- */
-
-static int it8212_noraid;
-
-/**
- * it821x_program - program the PIO/MWDMA registers
- * @drive: drive to tune
- * @timing: timing info
- *
- * Program the PIO/MWDMA timing for this channel according to the
- * current clock.
- */
-
-static void it821x_program(ide_drive_t *drive, u16 timing)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- int channel = hwif->channel;
- u8 conf;
-
- /* Program PIO/MWDMA timing bits */
- if(itdev->clock_mode == ATA_66)
- conf = timing >> 8;
- else
- conf = timing & 0xFF;
-
- pci_write_config_byte(dev, 0x54 + 4 * channel, conf);
-}
-
-/**
- * it821x_program_udma - program the UDMA registers
- * @drive: drive to tune
- * @timing: timing info
- *
- * Program the UDMA timing for this drive according to the
- * current clock.
- */
-
-static void it821x_program_udma(ide_drive_t *drive, u16 timing)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- int channel = hwif->channel;
- u8 unit = drive->dn & 1, conf;
-
- /* Program UDMA timing bits */
- if(itdev->clock_mode == ATA_66)
- conf = timing >> 8;
- else
- conf = timing & 0xFF;
-
- if (itdev->timing10 == 0)
- pci_write_config_byte(dev, 0x56 + 4 * channel + unit, conf);
- else {
- pci_write_config_byte(dev, 0x56 + 4 * channel, conf);
- pci_write_config_byte(dev, 0x56 + 4 * channel + 1, conf);
- }
-}
-
-/**
- * it821x_clock_strategy
- * @drive: drive to set up
- *
- * Select between the 50 and 66Mhz base clocks to get the best
- * results for this interface.
- */
-
-static void it821x_clock_strategy(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- ide_drive_t *pair = ide_get_pair_dev(drive);
- int clock, altclock, sel = 0;
- u8 unit = drive->dn & 1, v;
-
- if(itdev->want[0][0] > itdev->want[1][0]) {
- clock = itdev->want[0][1];
- altclock = itdev->want[1][1];
- } else {
- clock = itdev->want[1][1];
- altclock = itdev->want[0][1];
- }
-
- /*
- * if both clocks can be used for the mode with the higher priority
- * use the clock needed by the mode with the lower priority
- */
- if (clock == ATA_ANY)
- clock = altclock;
-
- /* Nobody cares - keep the same clock */
- if(clock == ATA_ANY)
- return;
- /* No change */
- if(clock == itdev->clock_mode)
- return;
-
- /* Load this into the controller ? */
- if(clock == ATA_66)
- itdev->clock_mode = ATA_66;
- else {
- itdev->clock_mode = ATA_50;
- sel = 1;
- }
-
- pci_read_config_byte(dev, 0x50, &v);
- v &= ~(1 << (1 + hwif->channel));
- v |= sel << (1 + hwif->channel);
- pci_write_config_byte(dev, 0x50, v);
-
- /*
- * Reprogram the UDMA/PIO of the pair drive for the switch
- * MWDMA will be dealt with by the dma switcher
- */
- if(pair && itdev->udma[1-unit] != UDMA_OFF) {
- it821x_program_udma(pair, itdev->udma[1-unit]);
- it821x_program(pair, itdev->pio[1-unit]);
- }
- /*
- * Reprogram the UDMA/PIO of our drive for the switch.
- * MWDMA will be dealt with by the dma switcher
- */
- if(itdev->udma[unit] != UDMA_OFF) {
- it821x_program_udma(drive, itdev->udma[unit]);
- it821x_program(drive, itdev->pio[unit]);
- }
-}
-
-/**
- * it821x_set_pio_mode - set host controller for PIO mode
- * @hwif: port
- * @drive: drive
- *
- * Tune the host to the desired PIO mode taking into the consideration
- * the maximum PIO mode supported by the other device on the cable.
- */
-
-static void it821x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- ide_drive_t *pair = ide_get_pair_dev(drive);
- const u8 pio = drive->pio_mode - XFER_PIO_0;
- u8 unit = drive->dn & 1, set_pio = pio;
-
- /* Spec says 89 ref driver uses 88 */
- static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
- static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
-
- /*
- * Compute the best PIO mode we can for a given device. We must
- * pick a speed that does not cause problems with the other device
- * on the cable.
- */
- if (pair) {
- u8 pair_pio = pair->pio_mode - XFER_PIO_0;
- /* trim PIO to the slowest of the master/slave */
- if (pair_pio < set_pio)
- set_pio = pair_pio;
- }
-
- /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
- itdev->want[unit][1] = pio_want[set_pio];
- itdev->want[unit][0] = 1; /* PIO is lowest priority */
- itdev->pio[unit] = pio_timings[set_pio];
- it821x_clock_strategy(drive);
- it821x_program(drive, itdev->pio[unit]);
-}
-
-/**
- * it821x_tune_mwdma - tune a channel for MWDMA
- * @drive: drive to set up
- * @mode_wanted: the target operating mode
- *
- * Load the timing settings for this device mode into the
- * controller when doing MWDMA in pass through mode. The caller
- * must manage the whole lack of per device MWDMA/PIO timings and
- * the shared MWDMA/PIO timing register.
- */
-
-static void it821x_tune_mwdma(ide_drive_t *drive, u8 mode_wanted)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif);
- u8 unit = drive->dn & 1, channel = hwif->channel, conf;
-
- static u16 dma[] = { 0x8866, 0x3222, 0x3121 };
- static u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY };
-
- itdev->want[unit][1] = mwdma_want[mode_wanted];
- itdev->want[unit][0] = 2; /* MWDMA is low priority */
- itdev->mwdma[unit] = dma[mode_wanted];
- itdev->udma[unit] = UDMA_OFF;
-
- /* UDMA bits off - Revision 0x10 do them in pairs */
- pci_read_config_byte(dev, 0x50, &conf);
- if (itdev->timing10)
- conf |= channel ? 0x60: 0x18;
- else
- conf |= 1 << (3 + 2 * channel + unit);
- pci_write_config_byte(dev, 0x50, conf);
-
- it821x_clock_strategy(drive);
- /* FIXME: do we need to program this ? */
- /* it821x_program(drive, itdev->mwdma[unit]); */
-}
-
-/**
- * it821x_tune_udma - tune a channel for UDMA
- * @drive: drive to set up
- * @mode_wanted: the target operating mode
- *
- * Load the timing settings for this device mode into the
- * controller when doing UDMA modes in pass through.
- */
-
-static void it821x_tune_udma(ide_drive_t *drive, u8 mode_wanted)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- u8 unit = drive->dn & 1, channel = hwif->channel, conf;
-
- static u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
- static u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };
-
- itdev->want[unit][1] = udma_want[mode_wanted];
- itdev->want[unit][0] = 3; /* UDMA is high priority */
- itdev->mwdma[unit] = MWDMA_OFF;
- itdev->udma[unit] = udma[mode_wanted];
- if(mode_wanted >= 5)
- itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */
-
- /* UDMA on. Again revision 0x10 must do the pair */
- pci_read_config_byte(dev, 0x50, &conf);
- if (itdev->timing10)
- conf &= channel ? 0x9F: 0xE7;
- else
- conf &= ~ (1 << (3 + 2 * channel + unit));
- pci_write_config_byte(dev, 0x50, conf);
-
- it821x_clock_strategy(drive);
- it821x_program_udma(drive, itdev->udma[unit]);
-
-}
+#include <linux/ide2libata.h>
+#include "../ata/pata_it821x.h"

/**
* it821x_dma_read - DMA hook
@@ -364,9 +47,9 @@ static void it821x_dma_start(ide_drive_t
u8 unit = drive->dn & 1;

if(itdev->mwdma[unit] != MWDMA_OFF)
- it821x_program(drive, itdev->mwdma[unit]);
+ it821x_program(hwif, drive, itdev->mwdma[unit]);
else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10)
- it821x_program_udma(drive, itdev->udma[unit]);
+ it821x_program_udma(hwif, drive, itdev->udma[unit]);
ide_dma_start(drive);
}

@@ -387,34 +70,11 @@ static int it821x_dma_end(ide_drive_t *d
u8 unit = drive->dn & 1;

if(itdev->mwdma[unit] != MWDMA_OFF)
- it821x_program(drive, itdev->pio[unit]);
+ it821x_program(hwif, drive, itdev->pio[unit]);
return ret;
}

/**
- * it821x_set_dma_mode - set host controller for DMA mode
- * @hwif: port
- * @drive: drive
- *
- * Tune the ITE chipset for the desired DMA mode.
- */
-
-static void it821x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- const u8 speed = drive->dma_mode;
-
- /*
- * MWDMA tuning is really hard because our MWDMA and PIO
- * timings are kept in the same place. We can switch in the
- * host dma on/off callbacks.
- */
- if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_6)
- it821x_tune_udma(drive, speed - XFER_UDMA_0);
- else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
- it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0);
-}
-
-/**
* it821x_cable_detect - cable detection
* @hwif: interface to check
*
@@ -587,23 +247,6 @@ static void __devinit init_hwif_it821x(i
}
}

-static void it8212_disable_raid(struct pci_dev *dev)
-{
- /* Reset local CPU, and set BIOS not ready */
- pci_write_config_byte(dev, 0x5E, 0x01);
-
- /* Set to bypass mode, and reset PCI bus */
- pci_write_config_byte(dev, 0x50, 0x00);
- pci_write_config_word(dev, PCI_COMMAND,
- PCI_COMMAND_PARITY | PCI_COMMAND_IO |
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
- pci_write_config_word(dev, 0x40, 0xA0F3);
-
- pci_write_config_dword(dev,0x4C, 0x02040204);
- pci_write_config_byte(dev, 0x42, 0x36);
- pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
-}
-
static int init_chipset_it821x(struct pci_dev *dev)
{
u8 conf;
@@ -613,7 +256,7 @@ static int init_chipset_it821x(struct pc
if (it8212_noraid) {
printk(KERN_INFO DRV_NAME " %s: forcing bypass mode\n",
pci_name(dev));
- it8212_disable_raid(dev);
+ it821x_disable_raid(dev);
}
pci_read_config_byte(dev, 0x50, &conf);
printk(KERN_INFO DRV_NAME " %s: controller in %s mode\n",
@@ -623,8 +266,8 @@ static int init_chipset_it821x(struct pc

static const struct ide_port_ops it821x_port_ops = {
/* it821x_set_{pio,dma}_mode() are only used in pass-through mode */
- .set_pio_mode = it821x_set_pio_mode,
- .set_dma_mode = it821x_set_dma_mode,
+ .set_pio_mode = it821x_passthru_set_piomode,
+ .set_dma_mode = it821x_passthru_set_dmamode,
.quirkproc = it821x_quirkproc,
.cable_detect = it821x_cable_detect,
};

\
 
 \ /
  Last update: 2010-01-29 17:17    [W:0.156 / U:1.192 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site