lkml.org 
[lkml]   [2010]   [Jan]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: Linux 2.6.33-rc5
On Sun, Jan 24, 2010 at 10:30:22AM -0800, Linus Torvalds wrote:
> On Sun, 24 Jan 2010, Borislav Petkov wrote:
> >
> > 1. After suspend, the right monitor shows very funny colors, as if it is
> > on crack, in contrast to the left one which looks fine:
> >
> > http://userweb.kernel.org/~bp/right_monitor.jpg
> > http://userweb.kernel.org/~bp/left_monitor.jpg
>
> Ok, at a guess, it looks like something isn't restoring the palette
> registers for the second output. You didn't say what GPU you have, but
> judging by your CC list, it's a radeon. You might want to let the Radeon
> KMS people know exactly what your setup is etc.

Good guessing, it's a radeon HD 3600 series (RV635 chip), pci
vendor/device id: 1002:9598, using radeonhd driver.

More specifically,

01:00.0 VGA compatible controller: ATI Technologies Inc Mobility Radeon HD 3600 Series (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device 01da
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR+ <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at feaf0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at d000 [size=256]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100] Vendor Specific Information <?>

X.org says:

(II) Primary Device is: PCI 01@00:00:0
(**) RADEONHD(0): Depth 24, (--) framebuffer bpp 32
(**) RADEONHD(0): Option "AccelMethod" "exa"
(**) RADEONHD(0): Option "DRI" "on"
(**) RADEONHD(0): Selected EXA 2D acceleration.
(II) RADEONHD(0): Card not in database: 0x9598:0x1043:0x01DA; using generic modesetting.
If - and only if - your card does not work or does not work optimally
please contact radeonhd@opensuse.org to help rectify this.
Use the subject: 0x9598:0x1043:0x01DA: <name of board>
and *please* describe the problems you are seeing
in your message.
(--) RADEONHD(0): Detected an RV635 on an unidentified card

config attached.

--
Regards/Gruss,
Boris.
[unhandled content-type:application/octet-stream]
\
 
 \ /
  Last update: 2010-01-24 20:11    [W:0.041 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site