[lkml]   [2009]   [Sep]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
    Subject[PATCH 0/4] compcache: in-memory compressed swapping v3
    Project home:

    * Changelog: v3 vs v2
    - All cleanups as suggested by Pekka.
    - Move to staging (drivers/block/ramzswap/ -> drivers/staging/ramzswap/).
    - Remove swap discard hooks -- swap notify support makes these redundant.
    - Unify duplicate code between init_device() fail path and reset_device().
    - Fix zero-page accounting.
    - Do not accept backing swap with bad pages.

    * Changelog: v2 vs initial revision
    - Use 'struct page' instead of 32-bit PFNs in ramzswap driver and xvmalloc.
    This is to make these 64-bit safe.
    - xvmalloc is no longer a separate module and does not export any symbols.
    Its compiled directly with ramzswap block driver. This is to avoid any
    last bit of confusion with any other allocator.
    - set_swap_free_notify() now accepts block_device as parameter instead of
    swp_entry_t (interface cleanup).
    - Fix: Make sure ramzswap disksize matches usable pages in backing swap file.
    This caused initialization error in case backing swap file had intra-page

    It creates RAM based block devices which can be used (only) as swap disks.
    Pages swapped to these disks are compressed and stored in memory itself. This
    is a big win over swapping to slow hard-disk which are typically used as swap
    disk. For flash, these suffer from wear-leveling issues when used as swap disk
    - so again its helpful. For swapless systems, it allows more apps to run for a
    given amount of memory.

    It can create multiple ramzswap devices (/dev/ramzswapX, X = 0, 1, 2, ...).
    Each of these devices can have separate backing swap (file or disk partition)
    which is used when incompressible page is found or memory limit for device is

    A separate userspace utility called rzscontrol is used to manage individual
    ramzswap devices.

    * Testing notes

    Tested on x86, x64, ARM
    - Cortex-A8 (Beagleboard)
    - ARM11 (Android G1)
    - OMAP2420 (Nokia N810)

    * Performance

    All performance numbers/plots can be found at:

    Below is a summary of this data:

    - Swap R/W times are reduced from milliseconds (in case of hard disks)
    down to microseconds.

    Positive cases:
    - Shows 33% improvement in 'scan' benchmark which allocates given amount
    of memory and linearly reads/writes to this region. This benchmark also
    exposes bottlenecks in ramzswap code (global mutex) due to which this gain
    is so small.
    - On Linux thin clients, it gives the effect of nearly doubling the amount of

    Negative cases:
    Any workload that has active working set w.r.t. filesystem cache that is
    nearly equal to amount of RAM while has minimal anonymous memory requirement,
    is expected to suffer maximum loss in performance with ramzswap enabled.

    Iozone filesystem benchmark can simulate exactly this kind of workload.
    As expected, this test shows performance loss of ~25% with ramzswap.

    drivers/staging/Kconfig | 2 +
    drivers/staging/Makefile | 1 +
    drivers/staging/ramzswap/Kconfig | 21 +
    drivers/staging/ramzswap/Makefile | 3 +
    drivers/staging/ramzswap/ramzswap.txt | 51 +
    drivers/staging/ramzswap/ramzswap_drv.c | 1462 +++++++++++++++++++++++++++++
    drivers/staging/ramzswap/ramzswap_drv.h | 173 ++++
    drivers/staging/ramzswap/ramzswap_ioctl.h | 50 +
    drivers/staging/ramzswap/xvmalloc.c | 533 +++++++++++
    drivers/staging/ramzswap/xvmalloc.h | 30 +
    drivers/staging/ramzswap/xvmalloc_int.h | 86 ++
    include/linux/swap.h | 5 +
    mm/swapfile.c | 34 +
    13 files changed, 2451 insertions(+), 0 deletions(-)

     \ /
      Last update: 2009-09-18 00:47    [W:0.031 / U:4.988 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site