lkml.org 
[lkml]   [2009]   [Jun]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2] usb: avoid PM error messages during resume if a device was disconnected
Date
On Wednesday 03 June 2009, Frans Pop wrote:
> Currently if a laptop is suspended e.g. while docked and then resumed after
> undocking it, the following errors get generated because the USB hub in the
> docking station and the devices connected to it are no longer available:
> pm_op(): usb_dev_resume+0x0/0x10 returns -19
> PM: Device 1-2 failed to resume: error -19
> pm_op(): usb_dev_resume+0x0/0x10 returns -19
> PM: Device 1-2.2 failed to resume: error -19
> pm_op(): usb_dev_resume+0x0/0x10 returns -19
> PM: Device 1-2.3 failed to resume: error -19
>
> As the removal of USB devices while a system is suspended is a relatively
> common use case and in most cases not an error, just return success on
> -ENODEV. The user gets informed anyway as the USB subsystem generates
> regular disconnect messages for the devices shortly afterwards:
> usb 1-2: USB disconnect, address 3
> usb 1-2.2: USB disconnect, address 4
> usblp0: removed
> usb 1-2.3: USB disconnect, address 5
>
> Signed-off-by: Frans Pop <elendil@planet.nl>
> Cc: Alan Stern <stern@rowland.harvard.edu>
> Cc: Rafael J. Wysocki <rjw@sisk.pl>
> ---
>
> On Tuesday 02 June 2009, Alan Stern wrote:
> > If we change -ENODEV to 0, the change should be made in usb_resume()
> > rather than usb_external_resume_device().
>
> Like so?
> Agreed that it's cleaner and tested that it works just as well :-)
>
> Cheers,
> FJP
>
> diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c
> index d0a21a5..0aaf26e 100644
> --- a/drivers/usb/core/driver.c
> +++ b/drivers/usb/core/driver.c
> @@ -1762,6 +1762,7 @@ int usb_suspend(struct device *dev, pm_message_t msg)
> int usb_resume(struct device *dev, pm_message_t msg)
> {
> struct usb_device *udev;
> + int status;
>
> udev = to_usb_device(dev);
>
> @@ -1771,7 +1772,14 @@ int usb_resume(struct device *dev, pm_message_t msg)
> */
> if (udev->skip_sys_resume)
> return 0;
> - return usb_external_resume_device(udev, msg);
> + status = usb_external_resume_device(udev, msg);
> +
> + /* Avoid PM error messages for devices disconnected while suspended
> + * as we'll display regular disconnect messages just a bit later.
> + */
> + if (status == -ENODEV)
> + return 0;
> + return status;

+ return status == -ENODEV ? 0 : status;

maybe?

> }
>
> #endif /* CONFIG_PM */

Best,
Rafael


\
 
 \ /
  Last update: 2009-06-03 00:57    [W:0.046 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site