lkml.org 
[lkml]   [2009]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/3] drivers/ide/ide-core: Convert printk(KERN_<level> to dev_<level>
Date
When hwif->name or drive->name is printed.

There is a single #ifdef DEBUG printk(KERN_DEBUG
that is also converted to dev_dbg.

Signed-off-by: Joe Perches <joe@perches.com>
---
drivers/ide/ide-atapi.c | 74 ++++++++++++++++++++++---------------------
drivers/ide/ide-dma-sff.c | 6 ++--
drivers/ide/ide-dma.c | 28 ++++++++--------
drivers/ide/ide-eh.c | 18 +++++-----
drivers/ide/ide-io.c | 18 +++-------
drivers/ide/ide-ioctls.c | 4 +-
drivers/ide/ide-iops.c | 9 ++---
drivers/ide/ide-lib.c | 4 +-
drivers/ide/ide-pm.c | 8 ++--
drivers/ide/ide-probe.c | 69 ++++++++++++++++++++-------------------
drivers/ide/ide-taskfile.c | 22 ++++++-------
drivers/ide/ide-xfer-mode.c | 6 ++--
drivers/ide/ide.c | 20 +++++-------
drivers/ide/setup-pci.c | 7 ++--
14 files changed, 142 insertions(+), 151 deletions(-)

diff --git a/drivers/ide/ide-atapi.c b/drivers/ide/ide-atapi.c
index ffa1bb8..fc5cfb6 100644
--- a/drivers/ide/ide-atapi.c
+++ b/drivers/ide/ide-atapi.c
@@ -50,21 +50,21 @@ int ide_check_atapi_device(ide_drive_t *drive, const char *s)
#endif

if (protocol != 2)
- printk(KERN_ERR "%s: %s: protocol (0x%02x) is not ATAPI\n",
- s, drive->name, protocol);
+ dev_err(&drive->gendev, "%s: protocol (0x%02x) is not ATAPI\n",
+ s, protocol);
else if ((drive->media == ide_floppy && device_type != 0) ||
(drive->media == ide_tape && device_type != 1))
- printk(KERN_ERR "%s: %s: invalid device type (0x%02x)\n",
- s, drive->name, device_type);
+ dev_err(&drive->gendev, "%s: invalid device type (0x%02x)\n",
+ s, device_type);
else if (removable == 0)
- printk(KERN_ERR "%s: %s: the removable flag is not set\n",
- s, drive->name);
+ dev_err(&drive->gendev, "%s: the removable flag is not set\n",
+ s);
else if (drive->media == ide_floppy && drq_type == 3)
- printk(KERN_ERR "%s: %s: sorry, DRQ type (0x%02x) not "
- "supported\n", s, drive->name, drq_type);
+ dev_err(&drive->gendev, "%s: sorry, DRQ type (0x%02x) not "
+ "supported\n", s, drq_type);
else if (packet_size != 0)
- printk(KERN_ERR "%s: %s: packet size (0x%02x) is not 12 "
- "bytes\n", s, drive->name, packet_size);
+ dev_err(&drive->gendev, "%s: packet size (0x%02x) is not 12 "
+ "bytes\n", s, packet_size);
else
return 1;
return 0;
@@ -201,8 +201,8 @@ void ide_prep_sense(ide_drive_t *drive, struct request *rq)
GFP_NOIO);
if (unlikely(err)) {
if (printk_ratelimit())
- printk(KERN_WARNING "%s: failed to map sense buffer\n",
- drive->name);
+ dev_warn(&drive->gendev,
+ "failed to map sense buffer\n");
return;
}

@@ -223,8 +223,7 @@ int ide_queue_sense_rq(ide_drive_t *drive, void *special)
{
/* deferred failure from ide_prep_sense() */
if (!drive->sense_rq_armed) {
- printk(KERN_WARNING "%s: failed queue sense request\n",
- drive->name);
+ dev_warn(&drive->gendev, "failed queue sense request\n");
return -ENOMEM;
}

@@ -365,9 +364,8 @@ static ide_startstop_t ide_pc_intr(ide_drive_t *drive)

if (rc || (drive->media == ide_tape && (stat & ATA_ERR))) {
if (drive->media == ide_floppy)
- printk(KERN_ERR "%s: DMA %s error\n",
- drive->name, rq_data_dir(pc->rq)
- ? "write" : "read");
+ dev_err(&drive->gendev, "DMA %s error\n",
+ rq_data_dir(pc->rq) ? "write" : "read");
pc->flags |= PC_FLAG_DMA_ERROR;
} else
pc->xferred = pc->req_xfer;
@@ -397,8 +395,8 @@ static ide_startstop_t ide_pc_intr(ide_drive_t *drive)
pc->rq->errors++;

if (rq->cmd[0] == REQUEST_SENSE) {
- printk(KERN_ERR "%s: I/O error in request sense"
- " command\n", drive->name);
+ dev_err(&drive->gendev,
+ "I/O error in request sense command\n");
return ide_do_reset(drive);
}

@@ -440,8 +438,9 @@ static ide_startstop_t ide_pc_intr(ide_drive_t *drive)

if (pc->flags & PC_FLAG_DMA_IN_PROGRESS) {
pc->flags &= ~PC_FLAG_DMA_IN_PROGRESS;
- printk(KERN_ERR "%s: The device wants to issue more interrupts "
- "in DMA mode\n", drive->name);
+ dev_err(&drive->gendev,
+ "The device wants to issue more interrupts "
+ "in DMA mode\n");
ide_dma_off(drive);
return ide_do_reset(drive);
}
@@ -450,16 +449,16 @@ static ide_startstop_t ide_pc_intr(ide_drive_t *drive)
ide_read_bcount_and_ireason(drive, &bcount, &ireason);

if (ireason & ATAPI_COD) {
- printk(KERN_ERR "%s: CoD != 0 in %s\n", drive->name, __func__);
+ dev_err(&drive->gendev, "CoD != 0 in %s\n", __func__);
return ide_do_reset(drive);
}

if (((ireason & ATAPI_IO) == ATAPI_IO) == write) {
/* Hopefully, we will never get here */
- printk(KERN_ERR "%s: We wanted to %s, but the device wants us "
- "to %s!\n", drive->name,
- (ireason & ATAPI_IO) ? "Write" : "Read",
- (ireason & ATAPI_IO) ? "Read" : "Write");
+ dev_err(&drive->gendev,
+ "We wanted to %s, but the device wants us to %s!\n",
+ (ireason & ATAPI_IO) ? "Write" : "Read",
+ (ireason & ATAPI_IO) ? "Read" : "Write");
return ide_do_reset(drive);
}

@@ -508,15 +507,16 @@ static u8 ide_wait_ireason(ide_drive_t *drive, u8 ireason)
int retries = 100;

while (retries-- && ((ireason & ATAPI_COD) == 0 ||
- (ireason & ATAPI_IO))) {
- printk(KERN_ERR "%s: (IO,CoD != (0,1) while issuing "
- "a packet command, retrying\n", drive->name);
+ (ireason & ATAPI_IO))) {
+ dev_err(&drive->gendev,
+ "(IO,CoD != (0,1) while issuing "
+ "a packet command, retrying\n");
udelay(100);
ireason = ide_read_ireason(drive);
if (retries == 0) {
- printk(KERN_ERR "%s: (IO,CoD != (0,1) while issuing "
- "a packet command, ignoring\n",
- drive->name);
+ dev_err(&drive->gendev,
+ "(IO,CoD != (0,1) while issuing "
+ "a packet command, ignoring\n");
ireason |= ATAPI_COD;
ireason &= ~ATAPI_IO;
}
@@ -546,8 +546,9 @@ static ide_startstop_t ide_transfer_pc(ide_drive_t *drive)
u8 ireason;

if (ide_wait_stat(&startstop, drive, ATA_DRQ, ATA_BUSY, WAIT_READY)) {
- printk(KERN_ERR "%s: Strange, packet command initiated yet "
- "DRQ isn't asserted\n", drive->name);
+ dev_err(&drive->gendev,
+ "Strange, packet command initiated yet "
+ "DRQ isn't asserted\n");
return startstop;
}

@@ -588,8 +589,9 @@ static ide_startstop_t ide_transfer_pc(ide_drive_t *drive)
ireason = ide_wait_ireason(drive, ireason);

if ((ireason & ATAPI_COD) == 0 || (ireason & ATAPI_IO)) {
- printk(KERN_ERR "%s: (IO,CoD) != (0,1) while issuing "
- "a packet command\n", drive->name);
+ dev_err(&drive->gendev,
+ "(IO,CoD) != (0,1) while issuing "
+ "a packet command\n");

return ide_do_reset(drive);
}
diff --git a/drivers/ide/ide-dma-sff.c b/drivers/ide/ide-dma-sff.c
index e4cdf78..9fcebf3 100644
--- a/drivers/ide/ide-dma-sff.c
+++ b/drivers/ide/ide-dma-sff.c
@@ -162,7 +162,7 @@ int ide_build_dmatable(ide_drive_t *drive, struct ide_cmd *cmd)
}

use_pio_instead:
- printk(KERN_ERR "%s: %s\n", drive->name,
+ dev_err(&drive->gendev, "%s\n",
count ? "DMA table too small" : "empty DMA table?");

return 0; /* revert to PIO for this request */
@@ -238,8 +238,8 @@ int ide_dma_sff_timer_expiry(ide_drive_t *drive)
ide_hwif_t *hwif = drive->hwif;
u8 dma_stat = hwif->dma_ops->dma_sff_read_status(hwif);

- printk(KERN_WARNING "%s: %s: DMA status (0x%02x)\n",
- drive->name, __func__, dma_stat);
+ dev_warn(&drive->gendev, "%s: DMA status (0x%02x)\n",
+ __func__, dma_stat);

if ((dma_stat & 0x18) == 0x18) /* BUSY Stupid Early Timer !! */
return WAIT_CMD;
diff --git a/drivers/ide/ide-dma.c b/drivers/ide/ide-dma.c
index 001f68f..47c2bde 100644
--- a/drivers/ide/ide-dma.c
+++ b/drivers/ide/ide-dma.c
@@ -106,8 +106,8 @@ ide_startstop_t ide_dma_intr(ide_drive_t *drive)
blk_rq_sectors(cmd->rq) << 9);
return ide_stopped;
}
- printk(KERN_ERR "%s: %s: bad DMA status (0x%02x)\n",
- drive->name, __func__, dma_stat);
+ dev_err(&drive->gendev, "%s: bad DMA status (0x%02x)\n",
+ __func__, dma_stat);
}
return ide_error(drive, "dma_intr", stat);
}
@@ -194,7 +194,7 @@ EXPORT_SYMBOL(ide_dma_off_quietly);

void ide_dma_off(ide_drive_t *drive)
{
- printk(KERN_INFO "%s: DMA disabled\n", drive->name);
+ dev_info(&drive->gendev, "DMA disabled\n");
ide_dma_off_quietly(drive);
}
EXPORT_SYMBOL(ide_dma_off);
@@ -220,8 +220,9 @@ int __ide_dma_bad_drive(ide_drive_t *drive)

int blacklist = ide_in_drive_list(id, drive_blacklist);
if (blacklist) {
- printk(KERN_WARNING "%s: Disabling (U)DMA for %s (blacklisted)\n",
- drive->name, (char *)&id[ATA_ID_PROD]);
+ dev_warn(&drive->gendev,
+ "Disabling (U)DMA for %s (blacklisted)\n",
+ (char *)&id[ATA_ID_PROD]);
return blacklist;
}
return 0;
@@ -342,8 +343,8 @@ u8 ide_find_dma_mode(ide_drive_t *drive, u8 req_mode)

mode = min(mode, req_mode);

- printk(KERN_INFO "%s: %s mode selected\n", drive->name,
- mode ? ide_xfer_verbose(mode) : "no DMA");
+ dev_info(&drive->gendev, "%s mode selected\n",
+ mode ? ide_xfer_verbose(mode) : "no DMA");

return mode;
}
@@ -409,7 +410,7 @@ int ide_id_dma_bug(ide_drive_t *drive)

return 0;
err_out:
- printk(KERN_ERR "%s: bad DMA info in identify block\n", drive->name);
+ dev_err(&drive->gendev, "bad DMA info in identify block\n");
return 1;
}

@@ -456,7 +457,7 @@ void ide_check_dma_crc(ide_drive_t *drive)

void ide_dma_lost_irq(ide_drive_t *drive)
{
- printk(KERN_ERR "%s: DMA interrupt recovery\n", drive->name);
+ dev_err(&drive->gendev, "DMA interrupt recovery\n");
}
EXPORT_SYMBOL_GPL(ide_dma_lost_irq);

@@ -478,17 +479,17 @@ ide_startstop_t ide_dma_timeout_retry(ide_drive_t *drive, int error)
*/

if (error < 0) {
- printk(KERN_WARNING "%s: DMA timeout error\n", drive->name);
+ dev_warn(&drive->gendev, "DMA timeout error\n");
drive->waiting_for_dma = 0;
(void)dma_ops->dma_end(drive);
ide_dma_unmap_sg(drive, cmd);
ret = ide_error(drive, "dma timeout error",
hwif->tp_ops->read_status(hwif));
} else {
- printk(KERN_WARNING "%s: DMA timeout retry\n", drive->name);
+ dev_warn(&drive->gendev, "DMA timeout retry\n");
if (dma_ops->dma_clear)
dma_ops->dma_clear(drive);
- printk(KERN_ERR "%s: timeout waiting for DMA\n", drive->name);
+ dev_err(&drive->gendev, "timeout waiting for DMA\n");
if (dma_ops->dma_test_irq(drive) == 0) {
ide_dump_status(drive, "DMA timeout",
hwif->tp_ops->read_status(hwif));
@@ -545,8 +546,7 @@ int ide_allocate_dma_engine(ide_hwif_t *hwif)
&hwif->dmatable_dma,
GFP_ATOMIC);
if (hwif->dmatable_cpu == NULL) {
- printk(KERN_ERR "%s: unable to allocate PRD table\n",
- hwif->name);
+ dev_err(&hwif->gendev, "unable to allocate PRD table\n");
return -ENOMEM;
}

diff --git a/drivers/ide/ide-eh.c b/drivers/ide/ide-eh.c
index 39d5892..75019ce 100644
--- a/drivers/ide/ide-eh.c
+++ b/drivers/ide/ide-eh.c
@@ -173,7 +173,7 @@ static ide_startstop_t atapi_reset_pollfunc(ide_drive_t *drive)
stat = tp_ops->read_status(hwif);

if (OK_STAT(stat, 0, ATA_BUSY))
- printk(KERN_INFO "%s: ATAPI reset complete\n", drive->name);
+ dev_info(&drive->gendev, "ATAPI reset complete\n");
else {
if (time_before(jiffies, hwif->poll_timeout)) {
ide_set_handler(drive, &atapi_reset_pollfunc, HZ/20);
@@ -182,8 +182,8 @@ static ide_startstop_t atapi_reset_pollfunc(ide_drive_t *drive)
}
/* end of polling */
hwif->polling = 0;
- printk(KERN_ERR "%s: ATAPI reset timed-out, status=0x%02x\n",
- drive->name, stat);
+ dev_err(&drive->gendev,
+ "ATAPI reset timed-out, status=0x%02x\n", stat);
/* do it the old fashioned way */
return do_reset1(drive, 1);
}
@@ -202,7 +202,7 @@ static void ide_reset_report_error(ide_hwif_t *hwif, u8 err)

u8 err_master = err & 0x7f;

- printk(KERN_ERR "%s: reset: master: ", hwif->name);
+ dev_err(&hwif->gendev, "reset: master: ");
if (err_master && err_master < 6)
printk(KERN_CONT "%s", err_master_vals[err_master]);
else
@@ -228,8 +228,9 @@ static ide_startstop_t reset_pollfunc(ide_drive_t *drive)
if (port_ops && port_ops->reset_poll) {
err = port_ops->reset_poll(drive);
if (err) {
- printk(KERN_ERR "%s: host reset_poll failure for %s.\n",
- hwif->name, drive->name);
+ dev_err(&hwif->gendev,
+ "host reset_poll failure for %s.\n",
+ drive->name);
goto out;
}
}
@@ -242,15 +243,14 @@ static ide_startstop_t reset_pollfunc(ide_drive_t *drive)
/* continue polling */
return ide_started;
}
- printk(KERN_ERR "%s: reset timed-out, status=0x%02x\n",
- hwif->name, tmp);
+ dev_err(&hwif->gendev, "reset timed-out, status=0x%02x\n", tmp);
drive->failures++;
err = -EIO;
} else {
tmp = ide_read_error(drive);

if (tmp == 1) {
- printk(KERN_INFO "%s: reset: success\n", hwif->name);
+ dev_info(&hwif->gendev, "reset: success\n");
drive->failures = 0;
} else {
ide_reset_report_error(hwif, tmp);
diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c
index 5015c5c..51c7cb4 100644
--- a/drivers/ide/ide-io.c
+++ b/drivers/ide/ide-io.c
@@ -95,8 +95,7 @@ void ide_complete_cmd(ide_drive_t *drive, struct ide_cmd *cmd, u8 stat, u8 err)
if ((cmd->tf_flags & IDE_TFLAG_CUSTOM_HANDLER) &&
tf_cmd == ATA_CMD_IDLEIMMEDIATE) {
if (tf->lbal != 0xc4) {
- printk(KERN_ERR "%s: head unload failed!\n",
- drive->name);
+ dev_err(&drive->gendev, "head unload failed!\n");
ide_tf_dump(drive->name, cmd);
} else
drive->dev_flags |= IDE_DFLAG_PARKED;
@@ -196,10 +195,7 @@ static ide_startstop_t do_special(ide_drive_t *drive)
{
struct ide_cmd cmd;

-#ifdef DEBUG
- printk(KERN_DEBUG "%s: %s: 0x%02x\n", drive->name, __func__,
- drive->special_flags);
-#endif
+ dev_dbg(&drive->gendev, "%s: 0x%02x\n", __func__, drive->special_flags);
if (drive->media != ide_disk) {
drive->special_flags = 0;
drive->mult_req = 0;
@@ -336,7 +332,7 @@ static ide_startstop_t start_request (ide_drive_t *drive, struct request *rq)
drive->hwif->tp_ops->dev_select(drive);
if (ide_wait_stat(&startstop, drive, drive->ready_stat,
ATA_BUSY | ATA_DRQ, WAIT_READY)) {
- printk(KERN_ERR "%s: drive not ready for command\n", drive->name);
+ dev_err(&drive->gendev, "drive not ready for command\n");
return startstop;
}

@@ -681,8 +677,7 @@ void ide_timer_expiry (unsigned long data)
hwif->dma_ops->dma_lost_irq(drive);
if (hwif->ack_intr)
hwif->ack_intr(hwif);
- printk(KERN_WARNING "%s: lost interrupt\n",
- drive->name);
+ dev_warn(&drive->gendev, "lost interrupt\n");
startstop = handler(drive);
} else {
if (drive->waiting_for_dma)
@@ -748,9 +743,8 @@ static void unexpected_intr(int irq, ide_hwif_t *hwif)

if (time_after(jiffies, last_msgtime + HZ)) {
last_msgtime = jiffies;
- printk(KERN_ERR "%s: unexpected interrupt, "
- "status=0x%02x, count=%ld\n",
- hwif->name, stat, count);
+ dev_err(&hwif->gendev, "unexpected interrupt, "
+ "status=0x%02x, count=%ld\n", stat, count);
}
}
}
diff --git a/drivers/ide/ide-ioctls.c b/drivers/ide/ide-ioctls.c
index 5991b23..866b29b 100644
--- a/drivers/ide/ide-ioctls.c
+++ b/drivers/ide/ide-ioctls.c
@@ -167,8 +167,8 @@ static int ide_cmd_ioctl(ide_drive_t *drive, unsigned long arg)
id[ATA_ID_SWDMA_MODES])) {
xfer_rate = args[1];
if (tf->nsect > XFER_UDMA_2 && !eighty_ninty_three(drive)) {
- printk(KERN_WARNING "%s: UDMA speeds >UDMA33 cannot "
- "be set\n", drive->name);
+ dev_warn(&drive->gendev,
+ "UDMA speeds >UDMA33 cannot be set\n");
goto abort;
}
}
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index c19a221..6dbb96e 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -259,10 +259,9 @@ no_80w:
if (drive->dev_flags & IDE_DFLAG_UDMA33_WARNED)
return 0;

- printk(KERN_WARNING "%s: %s side 80-wire cable detection failed, "
- "limiting max speed to UDMA33\n",
- drive->name,
- hwif->cbl == ATA_CBL_PATA80 ? "drive" : "host");
+ dev_warn(&drive->gendev, "%s side 80-wire cable detection failed, "
+ "limiting max speed to UDMA33\n",
+ hwif->cbl == ATA_CBL_PATA80 ? "drive" : "host");

drive->dev_flags |= IDE_DFLAG_UDMA33_WARNED;

@@ -300,7 +299,7 @@ int ide_driveid_update(ide_drive_t *drive)
out_err:
SELECT_MASK(drive, 0);
if (rc == 2)
- printk(KERN_ERR "%s: %s: bad status\n", drive->name, __func__);
+ dev_err(&drive->gendev, "%s: bad status\n", __func__);
kfree(id);
return 0;
}
diff --git a/drivers/ide/ide-lib.c b/drivers/ide/ide-lib.c
index 05b7fbc..f7432c5 100644
--- a/drivers/ide/ide-lib.c
+++ b/drivers/ide/ide-lib.c
@@ -151,7 +151,7 @@ u8 ide_dump_status(ide_drive_t *drive, const char *msg, u8 stat)
{
u8 err = 0;

- printk(KERN_ERR "%s: %s: status=0x%02x { ", drive->name, msg, stat);
+ dev_err(&drive->gendev, "%s: status=0x%02x { ", msg, stat);
if (stat & ATA_BUSY)
printk(KERN_CONT "Busy ");
else {
@@ -173,7 +173,7 @@ u8 ide_dump_status(ide_drive_t *drive, const char *msg, u8 stat)
printk(KERN_CONT "}\n");
if ((stat & (ATA_BUSY | ATA_ERR)) == ATA_ERR) {
err = ide_read_error(drive);
- printk(KERN_ERR "%s: %s: error=0x%02x ", drive->name, msg, err);
+ dev_err(&drive->gendev, "%s: error=0x%02x ", msg, err);
if (drive->media == ide_disk)
ide_dump_ata_error(drive, err);
else
diff --git a/drivers/ide/ide-pm.c b/drivers/ide/ide-pm.c
index c14ca14..f72531a 100644
--- a/drivers/ide/ide-pm.c
+++ b/drivers/ide/ide-pm.c
@@ -76,8 +76,8 @@ void ide_complete_power_step(ide_drive_t *drive, struct request *rq)
struct request_pm_state *pm = rq->special;

#ifdef DEBUG_PM
- printk(KERN_INFO "%s: complete_power_step(step: %d)\n",
- drive->name, pm->pm_step);
+ dev_info(&drive->gendev, "complete_power_step(step: %d)\n",
+ pm->pm_step);
#endif
if (drive->media != ide_disk)
return;
@@ -227,12 +227,12 @@ void ide_check_pm_state(ide_drive_t *drive, struct request *rq)
#endif
rc = ide_wait_not_busy(hwif, 35000);
if (rc)
- printk(KERN_WARNING "%s: bus not ready on wakeup\n", drive->name);
+ dev_warn(&drive->gendev, "bus not ready on wakeup\n");
tp_ops->dev_select(drive);
tp_ops->write_devctl(hwif, ATA_DEVCTL_OBS);
rc = ide_wait_not_busy(hwif, 100000);
if (rc)
- printk(KERN_WARNING "%s: drive not ready on wakeup\n", drive->name);
+ dev_warn(&drive->gendev, "drive not ready on wakeup\n");

spin_lock_irqsave(q->queue_lock, flags);
blk_start_queue(q);
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index 4002487..5672c27 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -116,8 +116,8 @@ static void ide_classify_ata_dev(ide_drive_t *drive)
if (!ata_id_has_unload(drive->id))
drive->dev_flags |= IDE_DFLAG_NO_UNLOAD;

- printk(KERN_INFO "%s: %s, %s DISK drive\n", drive->name, m,
- is_cfa ? "CFA" : "ATA");
+ dev_info(&drive->gendev, "%s, %s DISK drive\n",
+ m, is_cfa ? "CFA" : "ATA");
}

static void ide_classify_atapi_dev(ide_drive_t *drive)
@@ -126,7 +126,7 @@ static void ide_classify_atapi_dev(ide_drive_t *drive)
char *m = (char *)&id[ATA_ID_PROD];
u8 type = (id[ATA_ID_CONFIG] >> 8) & 0x1f;

- printk(KERN_INFO "%s: %s, ATAPI ", drive->name, m);
+ dev_info(&drive->gendev, "%s, ATAPI ", m);
switch (type) {
case ide_floppy:
if (!strstr(m, "CD-ROM")) {
@@ -203,7 +203,7 @@ static void do_identify(ide_drive_t *drive, u8 cmd, u16 *id)

drive->dev_flags |= IDE_DFLAG_ID_READ;
#ifdef DEBUG
- printk(KERN_INFO "%s: dumping identify data\n", drive->name);
+ dev_info(&drive->gendev, "dumping identify data\n");
ide_dump_identify((u8 *)id);
#endif
ide_fix_driveid(id);
@@ -271,9 +271,8 @@ int ide_dev_read_id(ide_drive_t *drive, u8 cmd, u16 *id)
s = tp_ops->read_status(hwif);
if ((a ^ s) & ~ATA_IDX)
/* ancient Seagate drives, broken interfaces */
- printk(KERN_INFO "%s: probing with STATUS(0x%02x) "
- "instead of ALTSTATUS(0x%02x)\n",
- drive->name, s, a);
+ dev_info(&drive->gendev, "probing with STATUS(0x%02x) "
+ "instead of ALTSTATUS(0x%02x)\n", s, a);
else
/* use non-intrusive polling */
use_altstatus = 1;
@@ -376,9 +375,10 @@ static int do_probe (ide_drive_t *drive, u8 cmd)
return 4;

#ifdef DEBUG
- printk(KERN_INFO "probing for %s: present=%d, media=%d, probetype=%s\n",
- drive->name, present, drive->media,
- (cmd == ATA_CMD_ID_ATA) ? "ATA" : "ATAPI");
+ dev_info(&drive->gendev,
+ "probing for %s: present=%d, media=%d, probetype=%s\n",
+ drive->name, present, drive->media,
+ (cmd == ATA_CMD_ID_ATA) ? "ATA" : "ATAPI");
#endif

/* needed for some systems
@@ -414,8 +414,9 @@ static int do_probe (ide_drive_t *drive, u8 cmd)
return 4;

if (rc == 1 && cmd == ATA_CMD_ID_ATAPI) {
- printk(KERN_ERR "%s: no response (status = 0x%02x), "
- "resetting drive\n", drive->name, stat);
+ dev_err(&drive->gendev,
+ "no response (status = 0x%02x), "
+ "resetting drive\n", stat);
msleep(50);
tp_ops->dev_select(drive);
msleep(50);
@@ -428,8 +429,8 @@ static int do_probe (ide_drive_t *drive, u8 cmd)
stat = tp_ops->read_status(hwif);

if (rc == 1)
- printk(KERN_ERR "%s: no response (status = 0x%02x)\n",
- drive->name, stat);
+ dev_err(&drive->gendev,
+ "no response (status = 0x%02x)\n", stat);
} else {
/* not present or maybe ATAPI */
rc = 3;
@@ -499,14 +500,15 @@ static u8 probe_for_drive(ide_drive_t *drive)
/* identification failed? */
if ((drive->dev_flags & IDE_DFLAG_ID_READ) == 0) {
if (drive->media == ide_disk) {
- printk(KERN_INFO "%s: non-IDE drive, CHS=%d/%d/%d\n",
- drive->name, drive->cyl,
- drive->head, drive->sect);
+ dev_info(&drive->gendev,
+ "non-IDE drive, CHS=%d/%d/%d\n",
+ drive->cyl, drive->head, drive->sect);
} else if (drive->media == ide_cdrom) {
- printk(KERN_INFO "%s: ATAPI cdrom (?)\n", drive->name);
+ dev_info(&drive->gendev, "ATAPI cdrom (?)\n");
} else {
/* nuke it */
- printk(KERN_WARNING "%s: Unknown device on bus refused identification. Ignoring.\n", drive->name);
+ dev_warn(&drive->gendev,
+ "Unknown device on bus refused identification. Ignoring.\n");
drive->dev_flags &= ~IDE_DFLAG_PRESENT;
}
} else {
@@ -812,8 +814,7 @@ static int ide_port_setup_devices(ide_hwif_t *hwif)
mutex_lock(&ide_cfg_mtx);
ide_port_for_each_present_dev(i, drive, hwif) {
if (ide_init_queue(drive)) {
- printk(KERN_ERR "ide: failed to init %s\n",
- drive->name);
+ dev_err(&drive->gendev, "ide: failed to init\n");
kfree(drive->id);
drive->id = NULL;
drive->dev_flags &= ~IDE_DFLAG_PRESENT;
@@ -847,12 +848,12 @@ static int init_irq (ide_hwif_t *hwif)
goto out_up;

#if !defined(__mc68000__)
- printk(KERN_INFO "%s at 0x%03lx-0x%03lx,0x%03lx on irq %d", hwif->name,
- io_ports->data_addr, io_ports->status_addr,
- io_ports->ctl_addr, hwif->irq);
+ dev_info(&hwif->gendev, "at 0x%03lx-0x%03lx,0x%03lx on irq %d",
+ io_ports->data_addr, io_ports->status_addr,
+ io_ports->ctl_addr, hwif->irq);
#else
- printk(KERN_INFO "%s at 0x%08lx on irq %d", hwif->name,
- io_ports->data_addr, hwif->irq);
+ dev_info(&hwif->gendev, "at 0x%08lx on irq %d",
+ io_ports->data_addr, hwif->irq);
#endif /* __mc68000__ */
if (hwif->host->host_flags & IDE_HFLAG_SERIALIZE)
printk(KERN_CONT " (serialized)");
@@ -955,7 +956,7 @@ static void drive_release_dev (struct device *dev)
static int hwif_init(ide_hwif_t *hwif)
{
if (!hwif->irq) {
- printk(KERN_ERR "%s: disabled, no IRQ\n", hwif->name);
+ dev_err(&hwif->gendev, "disabled, no IRQ\n");
return 0;
}

@@ -968,15 +969,15 @@ static int hwif_init(ide_hwif_t *hwif)
hwif->sg_table = kmalloc(sizeof(struct scatterlist)*hwif->sg_max_nents,
GFP_KERNEL);
if (!hwif->sg_table) {
- printk(KERN_ERR "%s: unable to allocate SG table.\n", hwif->name);
+ dev_err(&hwif->gendev, "unable to allocate SG table.\n");
goto out;
}

sg_init_table(hwif->sg_table, hwif->sg_max_nents);

if (init_irq(hwif)) {
- printk(KERN_ERR "%s: disabled, unable to get IRQ %d\n",
- hwif->name, hwif->irq);
+ dev_err(&hwif->gendev, "disabled, unable to get IRQ %d\n",
+ hwif->irq);
goto out;
}

@@ -1079,7 +1080,7 @@ static void ide_init_port(ide_hwif_t *hwif, unsigned int port,
rc = ide_hwif_setup_dma(hwif, d);

if (rc < 0) {
- printk(KERN_INFO "%s: DMA disabled\n", hwif->name);
+ dev_info(&hwif->gendev, "DMA disabled\n");

hwif->dma_ops = NULL;
hwif->dma_base = 0;
@@ -1336,7 +1337,7 @@ static void ide_disable_port(ide_hwif_t *hwif)
struct ide_host *host = hwif->host;
int i;

- printk(KERN_INFO "%s: disabling port\n", hwif->name);
+ dev_info(&hwif->gendev, "disabling port\n");

for (i = 0; i < MAX_HOST_PORTS; i++) {
if (host->ports[i] == hwif) {
@@ -1399,8 +1400,8 @@ int ide_host_register(struct ide_host *host, const struct ide_port_info *d,
continue;

if (hwif_init(hwif) == 0) {
- printk(KERN_INFO "%s: failed to initialize IDE "
- "interface\n", hwif->name);
+ dev_info(&hwif->gendev,
+ "failed to initialize IDE interface\n");
device_unregister(&hwif->gendev);
ide_disable_port(hwif);
continue;
diff --git a/drivers/ide/ide-taskfile.c b/drivers/ide/ide-taskfile.c
index 908e6c7..8d741d1 100644
--- a/drivers/ide/ide-taskfile.c
+++ b/drivers/ide/ide-taskfile.c
@@ -86,7 +86,7 @@ ide_startstop_t do_rw_taskfile(ide_drive_t *drive, struct ide_cmd *orig_cmd)
if (orig_cmd->protocol == ATA_PROT_PIO &&
(orig_cmd->tf_flags & IDE_TFLAG_MULTI_PIO) &&
drive->mult_count == 0) {
- printk(KERN_ERR "%s: multimode not set!\n", drive->name);
+ dev_err(&drive->gendev, "multimode not set!\n");
return ide_stopped;
}

@@ -215,7 +215,7 @@ static u8 wait_drive_not_busy(ide_drive_t *drive)
}

if (stat & ATA_BUSY)
- printk(KERN_ERR "%s: drive still BUSY!\n", drive->name);
+ dev_err(&drive->gendev, "drive still BUSY!\n");

return stat;
}
@@ -399,8 +399,7 @@ static ide_startstop_t pre_task_out_intr(ide_drive_t *drive,

if (ide_wait_stat(&startstop, drive, ATA_DRQ,
drive->bad_wstat, WAIT_DRQ)) {
- printk(KERN_ERR "%s: no DRQ after issuing %sWRITE%s\n",
- drive->name,
+ dev_err(&drive->gendev, "no DRQ after issuing %sWRITE%s\n",
(cmd->tf_flags & IDE_TFLAG_MULTI_PIO) ? "MULT" : "",
(drive->dev_flags & IDE_DFLAG_LBA48) ? "_EXT" : "");
return startstop;
@@ -580,9 +579,8 @@ int ide_taskfile_ioctl(ide_drive_t *drive, unsigned long arg)
case TASKFILE_MULTI_OUT:
if (!drive->mult_count) {
/* (hs): give up if multcount is not set */
- printk(KERN_ERR "%s: %s Multimode Write " \
- "multcount is not set\n",
- drive->name, __func__);
+ dev_err(&drive->gendev, "%s Multimode Write " \
+ "multcount is not set\n", __func__);
err = -EPERM;
goto abort;
}
@@ -600,9 +598,9 @@ int ide_taskfile_ioctl(ide_drive_t *drive, unsigned long arg)
case TASKFILE_MULTI_IN:
if (!drive->mult_count) {
/* (hs): give up if multcount is not set */
- printk(KERN_ERR "%s: %s Multimode Read failure " \
- "multcount is not set\n",
- drive->name, __func__);
+ dev_err(&drive->gendev,
+ "%s Multimode Read failure "
+ "multcount is not set\n", __func__);
err = -EPERM;
goto abort;
}
@@ -630,8 +628,8 @@ int ide_taskfile_ioctl(ide_drive_t *drive, unsigned long arg)
nsect = (cmd.hob.nsect << 8) | cmd.tf.nsect;

if (!nsect) {
- printk(KERN_ERR "%s: in/out command without data\n",
- drive->name);
+ dev_err(&drive->gendev,
+ "in/out command without data\n");
err = -EFAULT;
goto abort;
}
diff --git a/drivers/ide/ide-xfer-mode.c b/drivers/ide/ide-xfer-mode.c
index af44be9..023d6bb 100644
--- a/drivers/ide/ide-xfer-mode.c
+++ b/drivers/ide/ide-xfer-mode.c
@@ -70,7 +70,7 @@ u8 ide_get_best_pio_mode(ide_drive_t *drive, u8 mode_wanted, u8 max_mode)
pio_mode = ide_scan_pio_blacklist((char *)&id[ATA_ID_PROD]);

if (pio_mode != -1) {
- printk(KERN_INFO "%s: is on PIO blacklist\n", drive->name);
+ dev_info(&drive->gendev, "is on PIO blacklist\n");
} else {
pio_mode = id[ATA_ID_OLD_PIO_MODES] >> 8;
if (pio_mode > 2) { /* 2 is maximum allowed tPIO value */
@@ -96,8 +96,8 @@ u8 ide_get_best_pio_mode(ide_drive_t *drive, u8 mode_wanted, u8 max_mode)
}

if (overridden)
- printk(KERN_INFO "%s: tPIO > 2, assuming tPIO = 2\n",
- drive->name);
+ dev_info(&drive->gendev,
+ "tPIO > 2, assuming tPIO = 2\n");
}

if (pio_mode > max_mode)
diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c
index 92c9b90..fb2b180 100644
--- a/drivers/ide/ide.c
+++ b/drivers/ide/ide.c
@@ -273,25 +273,23 @@ static void ide_dev_apply_params(ide_drive_t *drive, u8 unit)
int i = drive->hwif->index * MAX_DRIVES + unit;

if (ide_nodma & (1 << i)) {
- printk(KERN_INFO "ide: disallowing DMA for %s\n", drive->name);
+ dev_info(&drive->gendev, "ide: disallowing DMA\n");
drive->dev_flags |= IDE_DFLAG_NODMA;
}
if (ide_noflush & (1 << i)) {
- printk(KERN_INFO "ide: disabling flush requests for %s\n",
- drive->name);
+ dev_info(&drive->gendev, "ide: disabling flush requests\n");
drive->dev_flags |= IDE_DFLAG_NOFLUSH;
}
if (ide_noprobe & (1 << i)) {
- printk(KERN_INFO "ide: skipping probe for %s\n", drive->name);
+ dev_info(&drive->gendev, "ide: skipping probe\n");
drive->dev_flags |= IDE_DFLAG_NOPROBE;
}
if (ide_nowerr & (1 << i)) {
- printk(KERN_INFO "ide: ignoring the ATA_DF bit for %s\n",
- drive->name);
+ dev_info(&drive->gendev, "ide: ignoring the ATA_DF bit\n");
drive->bad_wstat = BAD_R_STAT;
}
if (ide_cdroms & (1 << i)) {
- printk(KERN_INFO "ide: forcing %s as a CD-ROM\n", drive->name);
+ dev_info(&drive->gendev, "ide: forcing as a CD-ROM\n");
drive->dev_flags |= IDE_DFLAG_PRESENT;
drive->media = ide_cdrom;
/* an ATAPI device ignores DRDY */
@@ -302,9 +300,8 @@ static void ide_dev_apply_params(ide_drive_t *drive, u8 unit)
drive->head = drive->bios_head = ide_disks_chs[i].head;
drive->sect = drive->bios_sect = ide_disks_chs[i].sect;

- printk(KERN_INFO "ide: forcing %s as a disk (%d/%d/%d)\n",
- drive->name,
- drive->cyl, drive->head, drive->sect);
+ dev_info(&drive->gendev, "ide: forcing as a disk (%d/%d/%d)\n",
+ drive->cyl, drive->head, drive->sect);

drive->dev_flags |= IDE_DFLAG_FORCED_GEOM | IDE_DFLAG_PRESENT;
drive->media = ide_disk;
@@ -343,8 +340,7 @@ void ide_port_apply_params(ide_hwif_t *hwif)
int i;

if (ide_ignore_cable & (1 << hwif->index)) {
- printk(KERN_INFO "ide: ignoring cable detection for %s\n",
- hwif->name);
+ dev_info(&hwif->gendev, "ide: ignoring cable detection\n");
hwif->cbl = ATA_CBL_PATA40_SHORT;
}

diff --git a/drivers/ide/setup-pci.c b/drivers/ide/setup-pci.c
index 5314edf..3892351 100644
--- a/drivers/ide/setup-pci.c
+++ b/drivers/ide/setup-pci.c
@@ -384,10 +384,11 @@ int ide_hwif_setup_dma(ide_hwif_t *hwif, const struct ide_port_info *d)
return -1;

if (hwif->host_flags & IDE_HFLAG_MMIO)
- printk(KERN_INFO " %s: MMIO-DMA\n", hwif->name);
+ dev_info(&hwif->gendev, " MMIO-DMA\n");
else
- printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
- hwif->name, base, base + 7);
+ dev_info(&hwif->gendev,
+ " BM-DMA at 0x%04lx-0x%04lx\n",
+ base, base + 7);

hwif->extra_base = base + (hwif->channel ? 8 : 16);

--
1.6.3.1.10.g659a0.dirty


\
 
 \ /
  Last update: 2009-05-23 09:47    [W:0.091 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site