lkml.org 
[lkml]   [2009]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: USB/DVB - Old Technotrend TT-connect S-2400 regression tracked down
On Sat, 23 May 2009, David wrote:

> My PC (64 bit - ATI chipset, using 2.6.30-rc5)

Let's continue to work with 2.6.30-rc for testing purposes.

> [12044.364021] usb 4-10: new high speed USB device using ehci_hcd and address 5
> [12044.497561] usb 4-10: configuration #1 chosen from 1 choice
> [12044.881621] dvb-usb: found a 'Technotrend TT-connect S-2400' in cold state, will try to load a firmware
> [12044.881626] usb 4-10: firmware: requesting dvb-usb-tt-s2400-01.fw
> [12044.918854] dvb-usb: downloading firmware from file 'dvb-usb-tt-s2400-01.fw'
> [12044.980719] usbcore: registered new interface driver dvb_usb_ttusb2
> [12044.981478] usb 4-10: USB disconnect, address 5
> [12044.985169] dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
> [12046.744023] usb 4-10: new high speed USB device using ehci_hcd and address 6
> [12046.876980] usb 4-10: configuration #1 chosen from 1 choice
> [12046.877673] dvb-usb: found a 'Technotrend TT-connect S-2400' in warm state.
> [12046.878601] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
> [12046.878959] DVB: registering new adapter (Technotrend TT-connect S-2400)
> [12046.886861] DVB: registering adapter 0 frontend 0 (Philips TDA10086 DVB-S)...
> [12046.891434] LNBx2x attached on addr=8<3>dvb-usb: recv bulk message failed: -110
> [12048.888080] ttusb2: there might have been an error during control message transfer. (rlen = 0, was 0)
> [12048.888320] dvb-usb: Technotrend TT-connect S-2400 successfully initialized and connected.

Yes, there's an obvious problem.

> Reverting b963801164618e25fbdc0cd452ce49c3628b46c8 (manually, as there
> are conflicting changes) causes it to work again. The wierd random
> frontend number looks strange though.
>
> [ 2406.492027] usb 2-10: new high speed USB device using ehci_hcd and address 7
> [ 2406.625622] usb 2-10: configuration #1 chosen from 1 choice
> [ 2406.626328] dvb-usb: found a 'Technotrend TT-connect S-2400' in cold state, will try to load a firmware
> [ 2406.626335] usb 2-10: firmware: requesting dvb-usb-tt-s2400-01.fw
> [ 2406.628650] dvb-usb: downloading firmware from file 'dvb-usb-tt-s2400-01.fw'
> [ 2406.690868] usb 2-10: USB disconnect, address 7
> [ 2406.693282] dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
> [ 2408.453024] usb 2-10: new high speed USB device using ehci_hcd and address 8
> [ 2408.585983] usb 2-10: configuration #1 chosen from 1 choice
> [ 2408.586652] dvb-usb: found a 'Technotrend TT-connect S-2400' in warm state.
> [ 2408.587727] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
> [ 2408.588080] DVB: registering new adapter (Technotrend TT-connect S-2400)
> [ 2408.591575] DVB: registering adapter 0 frontend 42056112 (Philips TDA10086 DVB-S)...
> [ 2408.595941] LNBx2x attached on addr=8<6>dvb-usb: Technotrend TT-connect S-2400 successfully initialized and connected.

I don't know what's going on with that frontend number. In fact, I
don't know anything about DVB in general... but I am familiar with
EHCI.

It's not obvious what could be causing this, so let's start out easy.
Try collecting two usbmon traces (instructions are in
Documentation/usb/usbmon.txt), showing what happens with and without
the reversion. Maybe some difference will stick out.

Alan Stern



\
 
 \ /
  Last update: 2009-05-23 23:05    [W:0.061 / U:44.888 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site