Messages in this thread | | | Date | Wed, 22 Apr 2009 02:56:27 -0700 (PDT) | From | Martin Knoblauch <> | Subject | Re: Booting 2.6.30-rc2-git7 very slow |
| |
> From: Rafael J. Wysocki <rjw@sisk.pl>
> To: Martin Knoblauch <spamtrap@knobisoft.de> > Cc: linux-kernel@vger.kernel.org > Sent: Tuesday, April 21, 2009 9:12:20 PM > Subject: Re: Booting 2.6.30-rc2-git7 very slow > > On Tuesday 21 April 2009, Martin Knoblauch wrote: > > > > Hi, [please CC me on replies, as I am not subscribed] > > > > booting 2.6.30-rc2-git7 on a HP/DL380G3 (x86_64, RHEL4.3, 64 bit userspace) > is much slower that it used to be. It seems I run into timeouts when [trying to] > load intel and tg3 microcodes: > > > > [ 14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a > > [ 74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a > > [ 134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a > > [ 194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a > > [ 254.476493] Microcode Update Driver: v2.00 , > Peter Oruba > > [ 254.718489] Microcode Update Driver: v2.00 removed. > > > > So, we see 60 seconds for eaoch of the CPUs > > > > [ 255.273426] tg3 0000:03:01.0: PME# disabled > > [ 257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex. > > [ 257.833775] tg3: eth0: Flow control is off for TX and off for RX. > > [ 269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin > > [ 329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin" > > [ 329.640463] eth1: TSO capability disabled. > > [ 329.640487] tg3 0000:03:01.1: PME# disabled > > [ 333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex. > > [ 333.081759] tg3: eth1: Flow control is off for TX and off for RX. > > > > We see 60 seconds for eth1, complaining about a failed firmware load. > > /lib/firmware/tigon/tg3_tso.bin does exist and is from the current > > build. > > Do I assume correctly that 2.6.29 did not have this problem? >
Just checked. 2.6.29 has exactely the same problem. 2.6.28.2 was OK. This is from the 2.6.29 boot:
[ 14.308340] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 74.304612] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 134.304651] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 194.304638] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 254.304597] Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba [ 254.546200] Microcode Update Driver: v2.00 removed. [ 255.088405] tg3 0000:03:01.0: PME# disabled [ 257.669617] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 257.669622] tg3: eth0: Flow control is off for TX and off for RX. [ 269.456132] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin [ 329.456495] eth1: Failed to load firmware "tigon/tg3_tso.bin" [ 329.456500] eth1: TSO capability disabled. [ 329.456524] tg3 0000:03:01.1: PME# disabled [ 332.921832] tg3: eth1: Link is up at 1000 Mbps, full duplex. [ 332.921837] tg3: eth1: Flow control is off for TX and off for RX.
Cheers Martin
| |