[lkml]   [2009]   [Apr]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
    Subjectmutex_lock_slowpath warning using mxser tty driver (input/output error)
    Hi all,

    I have upgraded one of my automated test setups from 2.6.27 to 2.6.29. I
    now have issues with using a Moxa multiport serial device, where I had
    none before :-)

    > MOXA Smartio/Industio family driver version 2.0.4
    > mxser 0000:03:02.0: found MOXA C168H/PCI series board (BusNo=3,
    > mxser 0000:03:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    > mxser: max. baud rate = 921600 bps

    When I cat /dev/setup3 (which is a symlink to /dev/ttyMI3), which is
    connected to a device that outputs data (tried it with one @ 115200bps
    and one @ 9600bps), I get the following kernel trace:

    ------------[ cut here ]------------
    WARNING: at kernel/mutex.c:135 __mutex_lock_slowpath+0x50/0x211()
    Hardware name: OptiPlex 755
    Modules linked in: i915 drm i2c_algo_bit ipv6 8021q dummy fuse arc4 ecb
    snd_hda_codec_analog snd_hda_intel snd_hda_codec rtl8187 mac80211 usbhid
    i2c_i801 snd_pcm serio_raw eeprom_93cx6 iTCO_wdt i2c_core
    iTCO_vendor_support cfg80211 snd_timer snd snd_page_alloc rtc_cmos
    rtc_core intel_agp agpgart mxser ppdev thermal uhci_hcd sg rtc_lib
    parport_pc processor parport button thermal_sys dcdbas
    Pid: 0, comm: swapper Not tainted 2.6.29-autodistro-r4 #1
    Call Trace:
    [<c0127479>] warn_slowpath+0x74/0x8a
    [<c016bb1a>] ? get_page_from_freelist+0xc1/0x3c6
    [<c04e0093>] ? usb_hcd_submit_urb+0x88d/0x95b
    [<c05d2d41>] ? _spin_lock+0x8/0xb
    [<c0187063>] ? cache_alloc_refill+0x19f/0x499
    [<c05d1b63>] __mutex_lock_slowpath+0x50/0x211
    [<c05d1d36>] mutex_lock+0x12/0x15
    [<c026d677>] echo_set_canon_col+0x14/0x37
    [<c026e478>] n_tty_receive_buf+0x2f3/0xe0c
    [<c05d2d41>] ? _spin_lock+0x8/0xb
    [<c0187063>] ? cache_alloc_refill+0x19f/0x499
    [<c05d2e5e>] ? _spin_lock_irqsave+0x28/0x2f
    [<c012f01d>] ? lock_timer_base+0x1f/0x3e
    [<c0118b2d>] ? default_spin_lock_flags+0x8/0xb
    [<c0118b2d>] ? default_spin_lock_flags+0x8/0xb
    [<c02710ed>] flush_to_ldisc+0xe9/0x159
    [<c027119e>] tty_flip_buffer_push+0x41/0x51
    [<f842e5f5>] mxser_receive_chars+0x237/0x246 [mxser]
    [<f842fac5>] mxser_interrupt+0x18e/0x228 [mxser]
    [<c015ac54>] handle_IRQ_event+0x2a/0x5a
    [<c015c11a>] handle_fasteoi_irq+0x7b/0xb4
    [<c015c09f>] ? handle_fasteoi_irq+0x0/0xb4
    <IRQ> [<c0103527>] ? common_interrupt+0x27/0x2c
    [<c0108131>] ? mwait_idle+0x4c/0x5b
    [<c0101a5b>] ? cpu_idle+0x59/0x6d
    [<c05ce807>] ? start_secondary+0x19f/0x1a4
    ---[ end trace 433a17e91cdf059a ]---

    After I break the cat, subsequent cat's result in:

    cat /dev/setup3
    cat: /dev/setup3: Input/output error

    I'm not a kernel expert, so if you have any pointers or ways to provide
    more information, don't hesitate to ask.

    Christophe L.

     \ /
      Last update: 2009-04-02 18:47    [W:0.034 / U:50.860 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site