lkml.org 
[lkml]   [2009]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectAbout [AMCC 460EX/canyonlands board] Synopsys DesignWare Cores (DWC) SATA host driver
From
Mark,
I found that the current sata_dwc can only work on
DENX-2.6.25-stable, and have problems in DENX-2.6.26, 27, 28,
29(master),
the boot errors is as the following, I hope you and AMCC staff submit
it into mainline soon, thanks.

there is also some other boot panic kmsg, I will reproduce it tomorrow.

http://git.denx.de/linux-2.6-denx.git/

Synopsys DesignWare Cores (DWC) SATA host driver

linuxppc-dev@ozlabs.org

About AMCC DesignWare Core SATA controller driver:

=> boot
Using ip address 172.16.90.27
## Booting kernel from Legacy Image at ff600000 ...
Image Name: Linux-2.6.27.19
Created: 2009-03-13 10:18:17 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1574261 Bytes = 1.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Flattened Device Tree blob at fc1e0000
Booting using the fdt blob at 0xfc1e0000
## Loading init Ramdisk from Legacy Image at fc200000 ...
Image Name: canyonlands ramdisk rev. 001
Created: 2008-05-13 11:18:24 UTC
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 18968362 Bytes = 18.1 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Device Tree to 007fa000, end 007fffff ... OK
Loading Ramdisk to 1ec3d000, end 1fe53f2a ... OK
Using Canyonlands machine description
Linux version 2.6.27.19 (fedora@ubox-h1) (gcc version 4.2.2) #1 Fri
Mar 13 18:18:05 HKT 2009
Found initrd at 0xdec3d000:0xdfe53f2a
Zone PFN ranges:
DMA 0x00000000 -> 0x00020000
Normal 0x00020000 -> 0x00020000
HighMem 0x00020000 -> 0x00020000


scsi 0:0:0:0: Direct-Access ATA WDC WD10EVVS-63E 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda:<3>ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: link is slow to respond, please be patient (ready=0)
ata1: prereset failed (errno=-16)
ata1: reset failed, giving up
ata1.00: disabled
ata1: EH complete
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
unable to read partition table
sd 0:0:0:0: [sda] Attached SCSI disk
4cc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
4cc000000.nor_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Creating 7 MTD partitions on "4cc000000.nor_flash":
0x00000000-0x001e0000 : "kernel"
0x001e0000-0x00200000 : "dtb"
0x00200000-0x01600000 : "ramdisk"
0x01600000-0x01a00000 : "jffs2"
0x01a00000-0x03f60000 : "user"
0x03f60000-0x03fa0000 : "env"
0x03fa0000-0x04000000 : "u-boot"
NDFC NAND Driver initialized. Chip-Rev: 0x00000111
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND
128MiB 3,3V 8-bit)
Scanning device for bad blocks
Number of partitions 3
Creating 3 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x00100000 : "u-boot"
0x00100000-0x00140000 : "env"
0x00140000-0x08000000 : "content"
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
dwc_otg: version 2.60a 22-NOV-2006
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
eth0: link is up, 1000 FDX, pause enabled
IP-Config: Complete:
device=eth0, addr=172.16.90.27, mask=255.255.255.0, gw=255.255.255.255,
host=canyonlands, domain=, nis-domain=(none),
bootserver=172.16.90.26, rootserver=172.16.90.26, rootpath=
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 156k init
Startup utility found. Executing...
AMCC Startup utility launched.


BusyBox v1.2.1 (2008.05.13-11:11+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

~ # fdisk -l
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 8
Buffer I/O error on device sda, logical block 1
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 16
Buffer I/O error on device sda, logical block 2
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 24
Buffer I/O error on device sda, logical block 3
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 1953525160
Buffer I/O error on device sda, logical block 244190645
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 1953525160
Buffer I/O error on device sda, logical block 244190645
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 8
Buffer I/O error on device sda, logical block 1
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 16
Buffer I/O error on device sda, logical block 2
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 24
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 0
~ #


--
Cheng Renquan (程任全), from Shenzhen, China
Jean Anouilh - "What you get free costs too much."
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2009-03-18 14:01    [W:0.035 / U:0.608 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site