lkml.org 
[lkml]   [2009]   [Dec]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH 2/6] cmd64x: remove no longer needed debugging code
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Subject: [PATCH] cmd64x: remove no longer needed debugging code

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ide/cmd64x.c | 17 -----------------
1 file changed, 17 deletions(-)

Index: b/drivers/ide/cmd64x.c
===================================================================
--- a/drivers/ide/cmd64x.c
+++ b/drivers/ide/cmd64x.c
@@ -20,14 +20,6 @@

#define DRV_NAME "cmd64x"

-#define CMD_DEBUG 0
-
-#if CMD_DEBUG
-#define cmdprintk(x...) printk(x)
-#else
-#define cmdprintk(x...)
-#endif
-
/*
* CMD64x specific registers definition.
*/
@@ -76,9 +68,6 @@ static void program_cycle_times (ide_dri
{15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0};
static const u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM2, DRWTIM3};

- cmdprintk("program_cycle_times parameters: total=%d, active=%d\n",
- cycle_time, active_time);
-
cycle_count = quantize_timing( cycle_time, clock_time);
active_count = quantize_timing(active_time, clock_time);
recovery_count = cycle_count - active_count;
@@ -94,9 +83,6 @@ static void program_cycle_times (ide_dri
if (active_count > 16) /* shouldn't actually happen... */
active_count = 16;

- cmdprintk("Final counts: total=%d, active=%d, recovery=%d\n",
- cycle_count, active_count, recovery_count);
-
/*
* Convert values to internal chipset representation
*/
@@ -106,7 +92,6 @@ static void program_cycle_times (ide_dri
/* Program the active/recovery counts into the DRWTIM register */
drwtim = (active_count << 4) | recovery_count;
(void) pci_write_config_byte(dev, drwtim_regs[drive->dn], drwtim);
- cmdprintk("Write 0x%02x to reg 0x%x\n", drwtim, drwtim_regs[drive->dn]);
}

/*
@@ -150,7 +135,6 @@ static void cmd64x_tune_pio(ide_drive_t

if (setup_count > 5) /* shouldn't actually happen... */
setup_count = 5;
- cmdprintk("Final address setup count: %d\n", setup_count);

/*
* Program the address setup clocks into the ARTTIM registers.
@@ -162,7 +146,6 @@ static void cmd64x_tune_pio(ide_drive_t
arttim &= ~0xc0;
arttim |= setup_values[setup_count];
(void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim);
- cmdprintk("Write 0x%02x to reg 0x%x\n", arttim, arttim_regs[drive->dn]);
}

/*

\
 
 \ /
  Last update: 2009-12-03 20:55    [W:0.141 / U:0.248 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site