lkml.org 
[lkml]   [2009]   [Nov]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH] staging: rtl8187se: Remove card8185 variable to simplify flow
When this code is used for the rtl8187se, the value of card_8185
in struct r8180_priv is always 7 or 8. As a result, the program
flow can be simplified.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Bernhard Schiffner <bernhard@schiffner-limbach.de>
---

Index: wireless-testing/drivers/staging/rtl8187se/r8180_core.c
===================================================================
--- wireless-testing.orig/drivers/staging/rtl8187se/r8180_core.c
+++ wireless-testing/drivers/staging/rtl8187se/r8180_core.c
@@ -886,8 +886,6 @@ void rtl8180_rx_enable(struct net_device
rxconf = rxconf | (1<<ACCEPT_ALLMAC_FRAME_SHIFT);
}else{
rxconf = rxconf | (1<<ACCEPT_NICMAC_FRAME_SHIFT);
- if(priv->card_8185 == 0)
- rxconf = rxconf | (1<<RX_CHECK_BSSID_SHIFT);
}

if(priv->ieee80211->iw_mode == IW_MODE_MONITOR){
@@ -910,9 +908,6 @@ void rtl8180_rx_enable(struct net_device

rxconf = rxconf &~ RCR_CS_MASK;

- if (!priv->card_8185)
- rxconf |= (priv->rcr_csense<<RCR_CS_SHIFT);
-
write_nic_dword(dev, RX_CONF, rxconf);

fix_rx_fifo(dev);
@@ -964,28 +959,19 @@ void rtl8180_tx_enable(struct net_device

txconf = read_nic_dword(dev, TX_CONF);

- if (priv->card_8185) {
- byte = read_nic_byte(dev,CW_CONF);
- byte &= ~(1<<CW_CONF_PERPACKET_CW_SHIFT);
- byte &= ~(1<<CW_CONF_PERPACKET_RETRY_SHIFT);
- write_nic_byte(dev, CW_CONF, byte);
-
- tx_agc_ctl = read_nic_byte(dev, TX_AGC_CTL);
- tx_agc_ctl &= ~(1<<TX_AGC_CTL_PERPACKET_GAIN_SHIFT);
- tx_agc_ctl &= ~(1<<TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT);
- tx_agc_ctl |=(1<<TX_AGC_CTL_FEEDBACK_ANT);
- write_nic_byte(dev, TX_AGC_CTL, tx_agc_ctl);
- write_nic_byte(dev, 0xec, 0x3f); /* Disable early TX */
- }
-
- if (priv->card_8185)
- txconf = txconf &~ (1<<TCR_PROBE_NOTIMESTAMP_SHIFT);
- else {
- if(hwseqnum)
- txconf= txconf &~ (1<<TX_CONF_HEADER_AUTOICREMENT_SHIFT);
- else
- txconf= txconf | (1<<TX_CONF_HEADER_AUTOICREMENT_SHIFT);
- }
+ byte = read_nic_byte(dev, CW_CONF);
+ byte &= ~(1<<CW_CONF_PERPACKET_CW_SHIFT);
+ byte &= ~(1<<CW_CONF_PERPACKET_RETRY_SHIFT);
+ write_nic_byte(dev, CW_CONF, byte);
+
+ tx_agc_ctl = read_nic_byte(dev, TX_AGC_CTL);
+ tx_agc_ctl &= ~(1<<TX_AGC_CTL_PERPACKET_GAIN_SHIFT);
+ tx_agc_ctl &= ~(1<<TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT);
+ tx_agc_ctl |= (1<<TX_AGC_CTL_FEEDBACK_ANT);
+ write_nic_byte(dev, TX_AGC_CTL, tx_agc_ctl);
+ write_nic_byte(dev, 0xec, 0x3f); /* Disable early TX */
+
+ txconf = txconf & ~(1<<TCR_PROBE_NOTIMESTAMP_SHIFT);

txconf = txconf &~ TX_LOOPBACK_MASK;
txconf = txconf | (TX_LOOPBACK_NONE <<TX_LOOPBACK_SHIFT);
@@ -995,13 +981,10 @@ void rtl8180_tx_enable(struct net_device
txconf = txconf | (priv->retry_rts<<TX_RTSRETRY_SHIFT);
txconf = txconf &~ (1<<TX_NOCRC_SHIFT);

- if (priv->card_8185) {
- if (priv->hw_plcp_len)
- txconf = txconf &~ TCR_PLCP_LEN;
- else
- txconf = txconf | TCR_PLCP_LEN;
- } else
- txconf = txconf &~ TCR_SAT;
+ if (priv->hw_plcp_len)
+ txconf = txconf & ~TCR_PLCP_LEN;
+ else
+ txconf = txconf | TCR_PLCP_LEN;

txconf = txconf &~ TCR_MXDMA_MASK;
txconf = txconf | (TCR_MXDMA_2048<<TCR_MXDMA_SHIFT);
@@ -1720,8 +1703,6 @@ void rtl8180_rx(struct net_device *dev)
else
quality = 127 - quality;
priv->SignalQuality = quality;
- if(!priv->card_8185)
- printk("check your card type\n");

stats.signal = (u8)quality;//priv->wstats.qual.level = priv->SignalStrength;
stats.signalstrength = RXAGC;
@@ -2221,10 +2200,8 @@ short rtl8180_tx(struct net_device *dev,
*(tail+6) = 0;
*(tail+7) = 0;

- if(priv->card_8185){
- //FIXME: this should be triggered by HW encryption parameters.
- *tail |= (1<<15); //no encrypt
- }
+ /*FIXME: this should be triggered by HW encryption parameters.*/
+ *tail |= (1<<15); /* no encrypt */

if(remain==len && !descfrag) {
ownbit_flag = false; //added by david woo,2007.12.14
@@ -2266,7 +2243,7 @@ short rtl8180_tx(struct net_device *dev,

/* hw_plcp_len is not used for rtl8180 chip */
/* FIXME */
- if(priv->card_8185 == 0 || !priv->hw_plcp_len){
+ if (!priv->hw_plcp_len) {
duration = rtl8180_len2duration(len, rate, &ext);
*(tail+1) = *(tail+1) | ((duration & 0x7fff)<<16);
if(ext) *(tail+1) = *(tail+1) |(1<<31); //plcp length extension
@@ -2355,8 +2332,7 @@ void rtl8180_link_change(struct net_devi

rtl8180_set_mode(dev, EPROM_CMD_NORMAL);

- if(priv->card_8185)
- rtl8180_set_chan(dev, priv->chan);
+ rtl8180_set_chan(dev, priv->chan);
}

void rtl8180_rq_tx_ack(struct net_device *dev){
@@ -2702,8 +2678,6 @@ short rtl8180_init(struct net_device *de
struct r8180_priv *priv = ieee80211_priv(dev);
u16 word;
u16 version;
- u8 hw_version;
- //u8 config3;
u32 usValue;
u16 tmpu16;
int i, j;
@@ -2928,46 +2902,11 @@ short rtl8180_init(struct net_device *de

priv->InitialGain = 6;

- hw_version =( read_nic_dword(dev, TCR) & TCR_HWVERID_MASK)>>TCR_HWVERID_SHIFT;
+ DMESG("MAC controller is a RTL8187SE b/g");
+ priv->phy_ver = 2;

- switch (hw_version){
- case HW_VERID_R8185B_B:
- priv->card_8185 = VERSION_8187S_C;
- DMESG("MAC controller is a RTL8187SE b/g");
- priv->phy_ver = 2;
- break;
- case HW_VERID_R8185_ABC:
- DMESG("MAC controller is a RTL8185 b/g");
- priv->card_8185 = 1;
- /* you should not find a card with 8225 PHY ver < C*/
- priv->phy_ver = 2;
- break;
- case HW_VERID_R8185_D:
- DMESG("MAC controller is a RTL8185 b/g (V. D)");
- priv->card_8185 = 2;
- /* you should not find a card with 8225 PHY ver < C*/
- priv->phy_ver = 2;
- break;
- case HW_VERID_R8180_ABCD:
- DMESG("MAC controller is a RTL8180");
- priv->card_8185 = 0;
- break;
- case HW_VERID_R8180_F:
- DMESG("MAC controller is a RTL8180 (v. F)");
- priv->card_8185 = 0;
- break;
- default:
- DMESGW("MAC chip not recognized: version %x. Assuming RTL8180",hw_version);
- priv->card_8185 = 0;
- break;
- }
-
- if(priv->card_8185){
- priv->ieee80211->modulation |= IEEE80211_OFDM_MODULATION;
- priv->ieee80211->short_slot = 1;
- }
- /* you should not found any 8185 Ver B Card */
- priv->card_8185_Bversion = 0;
+ priv->ieee80211->modulation |= IEEE80211_OFDM_MODULATION;
+ priv->ieee80211->short_slot = 1;

// just for sync 85
priv->card_type = PCI;
@@ -3026,12 +2965,10 @@ short rtl8180_init(struct net_device *de
priv->chtxpwr[i]=word & 0xff;
priv->chtxpwr[i+1]=(word & 0xff00)>>8;
}
- if(priv->card_8185){
- for(i=1,j=0; i<14; i+=2,j++){
- word = eprom_read(dev,EPROM_TXPW_OFDM_CH1_2 + j);
- priv->chtxpwr_ofdm[i]=word & 0xff;
- priv->chtxpwr_ofdm[i+1]=(word & 0xff00)>>8;
- }
+ for (i = 1, j = 0; i < 14; i += 2, j++) {
+ word = eprom_read(dev, EPROM_TXPW_OFDM_CH1_2 + j);
+ priv->chtxpwr_ofdm[i] = word & 0xff;
+ priv->chtxpwr_ofdm[i+1] = (word & 0xff00)>>8;
}

//3Read crystal calibtration and thermal meter indication on 87SE.
@@ -3057,37 +2994,11 @@ short rtl8180_init(struct net_device *de

version = eprom_read(dev,EPROM_VERSION);
DMESG("EEPROM version %x",version);
- if( (!priv->card_8185) && version < 0x0101){
- DMESG ("EEPROM version too old, assuming defaults");
- DMESG ("If you see this message *plase* send your \
-DMESG output to andreamrl@tiscali.it THANKS");
- priv->digphy=1;
- priv->antb=0;
- priv->diversity=1;
- priv->cs_treshold=0xc;
- priv->rcr_csense=1;
- priv->rf_chip=RFCHIPID_PHILIPS;
- }else{
- if(!priv->card_8185){
- u8 rfparam = eprom_read(dev,RF_PARAM);
- DMESG("RfParam: %x",rfparam);
+ priv->rcr_csense = 3;

- priv->digphy = rfparam & (1<<RF_PARAM_DIGPHY_SHIFT) ? 0:1;
- priv->antb = rfparam & (1<<RF_PARAM_ANTBDEFAULT_SHIFT) ? 1:0;
+ priv->cs_treshold = (eprom_read(dev, ENERGY_TRESHOLD) & 0xff00) >> 8;

- priv->rcr_csense = (rfparam & RF_PARAM_CARRIERSENSE_MASK) >>
- RF_PARAM_CARRIERSENSE_SHIFT;
-
- priv->diversity =
- (read_nic_byte(dev,CONFIG2)&(1<<CONFIG2_ANTENNA_SHIFT)) ? 1:0;
- }else{
- priv->rcr_csense = 3;
- }
-
- priv->cs_treshold = (eprom_read(dev,ENERGY_TRESHOLD)&0xff00) >>8;
-
- priv->rf_chip = 0xff & eprom_read(dev,RFCHIPID);
- }
+ priv->rf_chip = 0xff & eprom_read(dev, RFCHIPID);

priv->rf_chip = RF_ZEBRA4;
priv->rf_sleep = rtl8225z4_rf_sleep;
@@ -3099,19 +3010,6 @@ DMESG output to andreamrl@tiscali.it THA
priv->rf_set_chan = rtl8225z2_rf_set_chan;
priv->rf_set_sens = NULL;

- if(!priv->card_8185){
- if(priv->antb)
- DMESG ("Antenna B is default antenna");
- else
- DMESG ("Antenna A is default antenna");
-
- if(priv->diversity)
- DMESG ("Antenna diversity is enabled");
- else
- DMESG("Antenna diversity is disabled");
-
- DMESG("Carrier sense %d",priv->rcr_csense);
- }

if (0!=alloc_rx_desc_ring(dev, priv->rxbuffersize, priv->rxringcount))
return -ENOMEM;
@@ -3144,17 +3042,6 @@ DMESG output to andreamrl@tiscali.it THA
TX_BEACON_RING_ADDR))
return -ENOMEM;

- if(!priv->card_8185){
- if(read_nic_byte(dev, CONFIG0) & (1<<CONFIG0_WEP40_SHIFT))
- DMESG ("40-bit WEP is supported in hardware");
- else
- DMESG ("40-bit WEP is NOT supported in hardware");
-
- if(read_nic_byte(dev,CONFIG0) & (1<<CONFIG0_WEP104_SHIFT))
- DMESG ("104-bit WEP is supported in hardware");
- else
- DMESG ("104-bit WEP is NOT supported in hardware");
- }
#if !defined(SA_SHIRQ)
if(request_irq(dev->irq, (void *)rtl8180_interrupt, IRQF_SHARED, dev->name, dev)){
#else
@@ -3172,17 +3059,6 @@ DMESG output to andreamrl@tiscali.it THA

void rtl8180_no_hw_wep(struct net_device *dev)
{
- struct r8180_priv *priv = ieee80211_priv(dev);
-
- if (!priv->card_8185) {
- u8 security;
-
- security = read_nic_byte(dev, SECURITY);
- security &=~(1<<SECURITY_WEP_TX_ENABLE_SHIFT);
- security &=~(1<<SECURITY_WEP_RX_ENABLE_SHIFT);
-
- write_nic_byte(dev, SECURITY, security);
- }
}

void rtl8180_set_hw_wep(struct net_device *dev)
@@ -3355,8 +3231,6 @@ void rtl8185_set_rate(struct net_device
void rtl8180_adapter_start(struct net_device *dev)
{
struct r8180_priv *priv = ieee80211_priv(dev);
- u32 anaparam;
- u16 word;
u8 config3;

rtl8180_rtx_disable(dev);
@@ -3384,12 +3258,6 @@ void rtl8180_adapter_start(struct net_de

rtl8180_update_msr(dev);

- if(!priv->card_8185){
- anaparam = eprom_read(dev,EPROM_ANAPARAM_ADDRLWORD);
- anaparam |= eprom_read(dev,EPROM_ANAPARAM_ADDRHWORD)<<16;
-
- rtl8180_set_anaparam(dev,anaparam);
- }
/* These might be unnecessary since we do in rx_enable / tx_enable */
fix_rx_fifo(dev);
fix_tx_fifo(dev);
@@ -3406,54 +3274,27 @@ void rtl8180_adapter_start(struct net_de
CONFIG2, read_nic_byte(dev,CONFIG2) &~\
(1<<CONFIG2_DMA_POLLING_MODE_SHIFT));
//^the nic isn't in test mode
- if(priv->card_8185)
- write_nic_byte(dev,
+ write_nic_byte(dev,
CONFIG2, read_nic_byte(dev,CONFIG2)|(1<<4));

rtl8180_set_mode(dev,EPROM_CMD_NORMAL);

write_nic_dword(dev,INT_TIMEOUT,0);

- if(!priv->card_8185)
- {
- /*
- experimental - this might be needed to calibrate AGC,
- anyway it shouldn't hurt
- */
- write_nic_byte(dev, CONFIG5,
- read_nic_byte(dev, CONFIG5) | (1<<AGCRESET_SHIFT));
- read_nic_byte(dev, CONFIG5);
- udelay(15);
- write_nic_byte(dev, CONFIG5,
- read_nic_byte(dev, CONFIG5) &~ (1<<AGCRESET_SHIFT));
- }else{
- write_nic_byte(dev, WPA_CONFIG, 0);
- //write_nic_byte(dev, TESTR, 0xd);
- }
+ write_nic_byte(dev, WPA_CONFIG, 0);

rtl8180_no_hw_wep(dev);

- if(priv->card_8185){
- rtl8185_set_rate(dev);
- write_nic_byte(dev, RATE_FALLBACK, 0x81);
- }else{
- word = read_nic_word(dev, BRSR);
- word &= ~BRSR_MBR;
- word &= ~BRSR_BPLCP;
- word |= ieeerate2rtlrate(priv->ieee80211->basic_rate);
- word |= 0x0f;
- write_nic_word(dev, BRSR, word);
- }
-
- if(priv->card_8185){
- write_nic_byte(dev, GP_ENABLE,read_nic_byte(dev, GP_ENABLE) & ~(1<<6));
-
- //FIXME cfg 3 ClkRun enable - isn't it ReadOnly ?
- rtl8180_set_mode(dev, EPROM_CMD_CONFIG);
- write_nic_byte(dev,CONFIG3, read_nic_byte(dev, CONFIG3)
- | (1 << CONFIG3_CLKRUN_SHIFT));
- rtl8180_set_mode(dev, EPROM_CMD_NORMAL);
- }
+ rtl8185_set_rate(dev);
+ write_nic_byte(dev, RATE_FALLBACK, 0x81);
+
+ write_nic_byte(dev, GP_ENABLE, read_nic_byte(dev, GP_ENABLE) & ~(1<<6));
+
+ /*FIXME cfg 3 ClkRun enable - isn't it ReadOnly ? */
+ rtl8180_set_mode(dev, EPROM_CMD_CONFIG);
+ write_nic_byte(dev, CONFIG3, read_nic_byte(dev, CONFIG3)
+ | (1 << CONFIG3_CLKRUN_SHIFT));
+ rtl8180_set_mode(dev, EPROM_CMD_NORMAL);

priv->rf_init(dev);

Index: wireless-testing/drivers/staging/rtl8187se/r8180.h
===================================================================
--- wireless-testing.orig/drivers/staging/rtl8187se/r8180.h
+++ wireless-testing/drivers/staging/rtl8187se/r8180.h
@@ -77,21 +77,6 @@ typedef enum _WIRELESS_MODE {
WIRELESS_MODE_AUTO = 0x08,
} WIRELESS_MODE;

-typedef enum _VERSION_8185{
- // RTL8185
- VERSION_8185_UNKNOWN,
- VERSION_8185_C, // C-cut
- VERSION_8185_D, // D-cut
- // RTL8185B
- VERSION_8185B_B, // B-cut
- VERSION_8185B_D, // D-cut
- VERSION_8185B_E, // E-cut
- //RTL8187S-PCIE
- VERSION_8187S_B, // B-cut
- VERSION_8187S_C, // C-cut
- VERSION_8187S_D, // D-cut
-
-}VERSION_8185,*PVERSION_8185;
typedef struct ChnlAccessSetting {
u16 SIFS_Timer;
u16 DIFS_Timer;
@@ -341,8 +326,6 @@ typedef struct r8180_priv
int irq;
struct ieee80211_device *ieee80211;

- short card_8185; /* O: rtl8180, 1:rtl8185 V B/C, 2:rtl8185 V D, 3:rtl8185B */
- short card_8185_Bversion; /* if TCR reports card V B/C this discriminates */
short phy_ver; /* meaningful for rtl8225 1:A 2:B 3:C */
short enable_gpio0;
enum card_type {PCI,MINIPCI,CARDBUS,USB/*rtl8187*/}card_type;
Index: wireless-testing/drivers/staging/rtl8187se/r8185b_init.c
===================================================================
--- wireless-testing.orig/drivers/staging/rtl8187se/r8185b_init.c
+++ wireless-testing/drivers/staging/rtl8187se/r8185b_init.c
@@ -1023,6 +1023,7 @@ ZEBRA_Config_85BASIC_HardCode(
u32 addr,data;
u32 u4bRegOffset, u4bRegValue, u4bRF23, u4bRF24;
u8 u1b24E;
+ int d_cut = 0;


//=============================================================================
@@ -1035,8 +1036,10 @@ ZEBRA_Config_85BASIC_HardCode(
u4bRF23= RF_ReadReg(dev, 0x08); mdelay(1);
u4bRF24= RF_ReadReg(dev, 0x09); mdelay(1);

- if (u4bRF23==0x818 && u4bRF24==0x70C && priv->card_8185 == VERSION_8187S_C)
- priv->card_8185 = VERSION_8187S_D;
+ if (u4bRF23 == 0x818 && u4bRF24 == 0x70C) {
+ d_cut = 1;
+ printk(KERN_INFO "rtl8187se: card type changed from C- to D-cut\n");
+ }

// Page0 : reg0-reg15

@@ -1070,18 +1073,9 @@ ZEBRA_Config_85BASIC_HardCode(

RF_WriteReg(dev, 0x03, 0x0806); mdelay(1);

- if(priv->card_8185 < VERSION_8187S_C)
- {
- RF_WriteReg(dev, 0x04, 0x03f7); mdelay(1);
- RF_WriteReg(dev, 0x05, 0x05ab); mdelay(1);
- RF_WriteReg(dev, 0x06, 0x00c1); mdelay(1);
- }
- else
- {
- RF_WriteReg(dev, 0x04, 0x03a7); mdelay(1);
- RF_WriteReg(dev, 0x05, 0x059b); mdelay(1);
- RF_WriteReg(dev, 0x06, 0x0081); mdelay(1);
- }
+ RF_WriteReg(dev, 0x04, 0x03a7); mdelay(1);
+ RF_WriteReg(dev, 0x05, 0x059b); mdelay(1);
+ RF_WriteReg(dev, 0x06, 0x0081); mdelay(1);


RF_WriteReg(dev, 0x07, 0x01A0); mdelay(1);
@@ -1091,14 +1085,11 @@ ZEBRA_Config_85BASIC_HardCode(
RF_WriteReg(dev, 0x0a, 0x0001); mdelay(1);
RF_WriteReg(dev, 0x0b, 0x0418); mdelay(1);

- if(priv->card_8185 == VERSION_8187S_D)
- {
+ if (d_cut) {
RF_WriteReg(dev, 0x0c, 0x0fbe); mdelay(1);
RF_WriteReg(dev, 0x0d, 0x0008); mdelay(1);
RF_WriteReg(dev, 0x0e, 0x0807); mdelay(1); // RX LO buffer
- }
- else
- {
+ } else {
RF_WriteReg(dev, 0x0c, 0x0fbe); mdelay(1);
RF_WriteReg(dev, 0x0d, 0x0008); mdelay(1);
RF_WriteReg(dev, 0x0e, 0x0806); mdelay(1); // RX LO buffer
Index: wireless-testing/drivers/staging/rtl8187se/r8180_rtl8225z2.c
===================================================================
--- wireless-testing.orig/drivers/staging/rtl8187se/r8180_rtl8225z2.c
+++ wireless-testing/drivers/staging/rtl8187se/r8180_rtl8225z2.c
@@ -445,30 +445,28 @@ s8 DbmToTxPwrIdx(struct r8180_priv *priv
* OFDM Power in dBm = Index * 0.5 + 0
* CCK Power in dBm = Index * 0.25 + 13
*/
- if (priv->card_8185 >= VERSION_8187S_B) {
- s32 tmp = 0;
+ s32 tmp = 0;

- if (WirelessMode == WIRELESS_MODE_G) {
- bUseDefault = false;
- tmp = (2 * PowerInDbm);
+ if (WirelessMode == WIRELESS_MODE_G) {
+ bUseDefault = false;
+ tmp = (2 * PowerInDbm);

- if (tmp < 0)
- TxPwrIdx = 0;
- else if (tmp > 40) /* 40 means 20 dBm. */
- TxPwrIdx = 40;
- else
- TxPwrIdx = (s8)tmp;
- } else if (WirelessMode == WIRELESS_MODE_B) {
- bUseDefault = false;
- tmp = (4 * PowerInDbm) - 52;
+ if (tmp < 0)
+ TxPwrIdx = 0;
+ else if (tmp > 40) /* 40 means 20 dBm. */
+ TxPwrIdx = 40;
+ else
+ TxPwrIdx = (s8)tmp;
+ } else if (WirelessMode == WIRELESS_MODE_B) {
+ bUseDefault = false;
+ tmp = (4 * PowerInDbm) - 52;

- if(tmp < 0)
- TxPwrIdx = 0;
- else if (tmp > 28) /* 28 means 20 dBm. */
- TxPwrIdx = 28;
- else
- TxPwrIdx = (s8)tmp;
- }
+ if (tmp < 0)
+ TxPwrIdx = 0;
+ else if (tmp > 28) /* 28 means 20 dBm. */
+ TxPwrIdx = 28;
+ else
+ TxPwrIdx = (s8)tmp;
}

/*
Index: wireless-testing/drivers/staging/rtl8187se/r8180_dm.c
===================================================================
--- wireless-testing.orig/drivers/staging/rtl8187se/r8180_dm.c
+++ wireless-testing/drivers/staging/rtl8187se/r8180_dm.c
@@ -197,7 +197,6 @@ DIG_Zebra(
{ // Advised from SD3 DZ
priv->InitialGain = 4; // In 87B, m74dBm means State 4 (m82dBm)
}
- //if(pHalData->VersionID != VERSION_8187B_B)
{ // Advised from SD3 DZ
OfdmFA1 = 0x20;
}

\
 
 \ /
  Last update: 2009-11-09 17:55    [W:0.030 / U:0.328 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site