Messages in this thread Patch in this message | | | Subject | Re: [PATCH] serial-core: resume serial hardware with no_console_suspend | From | Stanislav Brabec <> | Date | Sun, 18 Oct 2009 17:46:40 +0200 |
| |
Attaching rebased patch.
Untested! (Explained in the previous mail.)
Also sending a "diff -w" on the same code in the next mail for easier review.
-
BIOS-less devices may require hardware resume for proper work. It did not happen with no_console_suspend (at least before ba15ab0e).
Perform a tricky suspend/resume with no_console_suspend.
Attempt to: - Save the hardware state - Perform buffer flush in time of its suspend call - Tell the driver that port is suspended - But still accept new data - And keep console hardware in state that allows to send them
Signed-off-by: Stanislav Brabec <utx@penguin.cz>
diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c index dcc7244..f1e1ab2 100644 --- a/drivers/serial/serial_core.c +++ b/drivers/serial/serial_core.c @@ -2008,12 +2008,6 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport) mutex_lock(&port->mutex); - if (!console_suspend_enabled && uart_console(uport)) { - /* we're going to avoid suspending serial console */ - mutex_unlock(&port->mutex); - return 0; - } - tty_dev = device_find_child(uport->dev, &match, serial_match_port); if (device_may_wakeup(tty_dev)) { enable_irq_wake(uport->irq); @@ -2021,20 +2015,23 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport) mutex_unlock(&port->mutex); return 0; } - uport->suspended = 1; + if (console_suspend_enabled || !uart_console(uport)) + uport->suspended = 1; if (port->flags & ASYNC_INITIALIZED) { const struct uart_ops *ops = uport->ops; int tries; - set_bit(ASYNCB_SUSPENDED, &port->flags); - clear_bit(ASYNCB_INITIALIZED, &port->flags); + if (console_suspend_enabled || !uart_console(uport)) { + set_bit(ASYNCB_SUSPENDED, &port->flags); + clear_bit(ASYNCB_INITIALIZED, &port->flags); - spin_lock_irq(&uport->lock); - ops->stop_tx(uport); - ops->set_mctrl(uport, 0); - ops->stop_rx(uport); - spin_unlock_irq(&uport->lock); + spin_lock_irq(&uport->lock); + ops->stop_tx(uport); + ops->set_mctrl(uport, 0); + ops->stop_rx(uport); + spin_unlock_irq(&uport->lock); + } /* * Wait for the transmitter to empty. @@ -2049,16 +2046,18 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport) drv->dev_name, drv->tty_driver->name_base + uport->line); - ops->shutdown(uport); + if (console_suspend_enabled || !uart_console(uport)) + ops->shutdown(uport); } /* * Disable the console device before suspending. */ - if (uart_console(uport)) + if (console_suspend_enabled && uart_console(uport)) console_stop(uport->cons); - uart_change_pm(state, 3); + if (console_suspend_enabled || !uart_console(uport)) + uart_change_pm(state, 3); mutex_unlock(&port->mutex); @@ -2075,29 +2074,6 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport) mutex_lock(&port->mutex); - if (!console_suspend_enabled && uart_console(uport)) { - /* no need to resume serial console, it wasn't suspended */ - /* - * First try to use the console cflag setting. - */ - memset(&termios, 0, sizeof(struct ktermios)); - termios.c_cflag = uport->cons->cflag; - /* - * If that's unset, use the tty termios setting. - */ - if (termios.c_cflag == 0) - termios = *state->port.tty->termios; - else { - termios.c_ispeed = termios.c_ospeed = - tty_termios_input_baud_rate(&termios); - termios.c_ispeed = termios.c_ospeed = - tty_termios_baud_rate(&termios); - } - uport->ops->set_termios(uport, &termios, NULL); - mutex_unlock(&port->mutex); - return 0; - } - tty_dev = device_find_child(uport->dev, &match, serial_match_port); if (!uport->suspended && device_may_wakeup(tty_dev)) { disable_irq_wake(uport->irq); @@ -2123,21 +2099,23 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport) spin_lock_irq(&uport->lock); ops->set_mctrl(uport, 0); spin_unlock_irq(&uport->lock); - ret = ops->startup(uport); - if (ret == 0) { - uart_change_speed(state, NULL); - spin_lock_irq(&uport->lock); - ops->set_mctrl(uport, uport->mctrl); - ops->start_tx(uport); - spin_unlock_irq(&uport->lock); - set_bit(ASYNCB_INITIALIZED, &port->flags); - } else { - /* - * Failed to resume - maybe hardware went away? - * Clear the "initialized" flag so we won't try - * to call the low level drivers shutdown method. - */ - uart_shutdown(state); + if (console_suspend_enabled || !uart_console(uport)) { + ret = ops->startup(uport); + if (ret == 0) { + uart_change_speed(state, NULL); + spin_lock_irq(&uport->lock); + ops->set_mctrl(uport, uport->mctrl); + ops->start_tx(uport); + spin_unlock_irq(&uport->lock); + set_bit(ASYNCB_INITIALIZED, &port->flags); + } else { + /* + * Failed to resume - maybe hardware went away? + * Clear the "initialized" flag so we won't try + * to call the low level drivers shutdown method. + */ + uart_shutdown(state); + } } clear_bit(ASYNCB_SUSPENDED, &port->flags);
________________________________________________________________________ Stanislav Brabec http://www.penguin.cz/~utx -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |