Messages in this thread | | | From | "Doug Bazarnic" <> | Subject | GPF on 2.6.28 & 2.6.28-rc9-git3 e1000e / e1000 issues | Date | Fri, 9 Jan 2009 14:26:49 -0700 |
| |
Ive moved mem3 back onto the onboard e1000e nics, and every 12 hours or so, a hard lockup occurs with heavy traffic on eth1. When on the e1000 pci-x nics, Id only get an occasional Tx Unit Hang.
This happens on both 2.6.28 and 2.6.28-rc9-git3, which was stable on the e1000s.
This is a dual Xeon Quad, with 32g of ram, tyan s5397 motherboard, running Centos 5.2 x86_64.
This is the first time I saw something on the console:
mem3 kernel: general protection fault: 0000 [#1] SMP mem3 kernel: last sysfs file: /sys/class/scsi_host/host8/proc_name mem3 kernel: Stack: mem3 kernel: ffffe200184c28e0 0000000000000000 ffff88079b0c9350 0000000000000246 mem3 kernel: ffff88079b0c9580 ffff88081ec6be80 ffff8806ce08d640 ffff8807390da180 mem3 kernel: Call Trace: mem3 kernel: [<ffffffff803a1e20>] ? xfs_get_blocks+0x0/0x10 mem3 kernel: [<ffffffff80585198>] ? tcp_transmit_skb+0x3a8/0x6d0 mem3 kernel: [<ffffffff802c55bd>] ? mpage_readpage+0x4d/0x70 mem3 kernel: [<ffffffff803a1e20>] ? xfs_get_blocks+0x0/0x10 mem3 kernel: [<ffffffff8058693d>] ? __tcp_push_pending_frames+0x14d/0x7e0 mem3 kernel: [<ffffffff803ecc29>] ? radix_tree_next_hole+0x39/0x50 mem3 kernel: [<ffffffff80278cca>] ? ondemand_readahead+0x12a/0x1b0 mem3 kernel: [<ffffffff80272485>] ? generic_file_aio_read+0x1a5/0x5d0 mem3 kernel: [<ffffffff803a95da>] ? xfs_read+0x10a/0x240 mem3 kernel: [<ffffffff8029c209>] ? do_sync_read+0xd9/0x120 mem3 kernel: [<ffffffff8024c0a0>] ? autoremove_wake_function+0x0/0x30 mem3 kernel: [<ffffffff8029cb35>] ? vfs_read+0xc5/0x160 mem3 kernel: [<ffffffff8029cf13>] ? sys_read+0x53/0x90 mem3 kernel: [<ffffffff8020b5bb>] ? system_call_fastpath+0x16/0x1b mem3 kernel: Code: 00 00 00 48 89 7c 24 28 48 89 74 24 20 89 54 24 1c 48 89 4c 24 10 4c 89 4c 24 08 48 8b 84 24 d0 00 00 00 48 89 04 24 48 8b 46 18 <48> 8b 00 48 89 44 24 30 8b 90 a0 00 00 00 89 54 24 3c f6 46 01 mem3 kernel: general protection fault: 0000 [#2] SMP mem3 kernel: last sysfs file: /sys/class/scsi_host/host8/proc_name
This server is under heavy load.
====dmesg==== IOS EBDA/lowmem at: 0009a000/0009a000 Linux version 2.6.28-rc9-git3 (root@mem3) (gcc version 4.1.2 20071124 (Red Hat 4.1.2-42)) #2 SMP Wed Jan 7 14:06:58 MST 2009 Command line: ro root=LABEL=/ KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009a000 (usable) BIOS-e820: 000000000009a000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000c8000 - 00000000000cc000 (reserved) BIOS-e820: 00000000000d0000 - 00000000000dc000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000bff50000 (usable) BIOS-e820: 00000000bff50000 - 00000000bff5f000 (ACPI data) BIOS-e820: 00000000bff5f000 - 00000000bff60000 (ACPI NVS) BIOS-e820: 00000000bff60000 - 00000000c0000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000840000000 (usable) DMI present. Phoenix BIOS detected: BIOS may corrupt low RAM, working it around. last_pfn = 0x840000 max_arch_pfn = 0x3ffffffff x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 ------------[ cut here ]------------ WARNING: at arch/x86/kernel/cpu/mtrr/generic.c:404 generic_get_mtrr+0x11e/0x130() mtrr: your BIOS has set up an incorrect mask, fixing it up. Modules linked in: Pid: 0, comm: swapper Not tainted 2.6.28-rc9-git3 #2 Call Trace: [<ffffffff802378fc>] warn_slowpath+0x10c/0x150 [<ffffffff802500e6>] up+0x16/0x50 [<ffffffff80238197>] release_console_sem+0x197/0x1d0 [<ffffffff8023884d>] printk+0x8d/0xa0 [<ffffffff8021947e>] generic_get_mtrr+0x11e/0x130 [<ffffffff80789d0d>] mtrr_trim_uncached_memory+0xcd/0x670 [<ffffffff80791fc8>] early_gart_iommu_check+0xb8/0x2d0 [<ffffffff80218e60>] post_set+0x20/0x40 [<ffffffff80785e8e>] setup_arch+0x36e/0x6d0 [<ffffffff8077ea8d>] start_kernel+0x5d/0x360 [<ffffffff8077e3aa>] x86_64_start_kernel+0xca/0xe0 ---[ end trace 4eaa2a86a8e2da22 ]--- last_pfn = 0xbff50 max_arch_pfn = 0x3ffffffff init_memory_mapping: 0000000000000000-00000000bff50000 0000000000 - 00bfe00000 page 2M 00bfe00000 - 00bff50000 page 4k kernel direct mapping tables up to bff50000 @ 10000-15000 last_map_addr: bff50000 end: bff50000 init_memory_mapping: 0000000100000000-0000000840000000 0100000000 - 0840000000 page 2M kernel direct mapping tables up to 840000000 @ 13000-35000 last_map_addr: 840000000 end: 840000000 RAMDISK: 37dd3000 - 37fefaa2 ACPI: RSDP 000F7050, 0024 (r2 PTLTD ) ACPI: XSDT BFF58E4B, 009C (r1 PTLTD XSDT 6040000 LTP 0) ACPI: FACP BFF5ED60, 00F4 (r3 INTEL TUMWATER 6040000 PTL 3) ACPI: DSDT BFF5A9B9, 4333 (r1 Intel SEABURG 6040000 MSFT 3000000) ACPI: FACS BFF5FFC0, 0040 ACPI: _MAR BFF5EE54, 0030 (r1 Intel OEMDMAR 6040000 LOHR 1) ACPI: APIC BFF5EE84, 00C8 (r1 PTLTD APIC 6040000 LTP 0) ACPI: MCFG BFF5EF4C, 003C (r1 PTLTD MCFG 6040000 LTP 0) ACPI: BOOT BFF5EF88, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) ACPI: SPCR BFF5EFB0, 0050 (r1 PTLTD $UCRTBL$ 6040000 PTL 1) ACPI: SSDT BFF5A75A, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050228) ACPI: SSDT BFF5A6B4, 00A6 (r1 PmRef Cpu7Tst 3000 INTL 20050228) ACPI: SSDT BFF5A60E, 00A6 (r1 PmRef Cpu6Tst 3000 INTL 20050228) ACPI: SSDT BFF5A568, 00A6 (r1 PmRef Cpu5Tst 3000 INTL 20050228) ACPI: SSDT BFF5A4C2, 00A6 (r1 PmRef Cpu4Tst 3000 INTL 20050228) ACPI: SSDT BFF5A41C, 00A6 (r1 PmRef Cpu3Tst 3000 INTL 20050228) ACPI: SSDT BFF5A376, 00A6 (r1 PmRef Cpu2Tst 3000 INTL 20050228) ACPI: SSDT BFF5A2D0, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20050228) ACPI: SSDT BFF58EE7, 13E9 (r1 PmRef CpuPm 3000 INTL 20050228) ACPI: Local APIC address 0xfee00000 (7 early reservations) ==> bootmem [0000000000 - 0840000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #2 [0000200000 - 0000889b74] TEXT DATA BSS ==> [0000200000 - 0000889b74] #3 [0037dd3000 - 0037fefaa2] RAMDISK ==> [0037dd3000 - 0037fefaa2] #4 [000009a000 - 0000100000] BIOS reserved ==> [000009a000 - 0000100000] #5 [0000010000 - 0000013000] PGTABLE ==> [0000010000 - 0000013000] #6 [0000013000 - 0000030000] PGTABLE ==> [0000013000 - 0000030000] [ffffe20000000000-ffffe2000f9fffff] PMD -> [ffff880028200000-ffff880037bfffff] on node 0 [ffffe2000fa00000-ffffe2001cdfffff] PMD -> [ffff880038000000-ffff8800453fffff] on node 0 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x00840000 Movable zone start PFN for each node early_node_map[3] active PFN ranges 0: 0x00000010 -> 0x0000009a 0: 0x00000100 -> 0x000bff50 0: 0x00100000 -> 0x00840000 On node 0 totalpages: 8388314 DMA zone: 56 pages used for memmap DMA zone: 1810 pages reserved DMA zone: 2112 pages, LIFO batch:0 DMA32 zone: 14280 pages used for memmap DMA32 zone: 767880 pages, LIFO batch:31 Normal zone: 103936 pages used for memmap Normal zone: 7498240 pages, LIFO batch:31 Movable zone: 0 pages used for memmap ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1]) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x09] address[0xfec88000] gsi_base[24]) IOAPIC[1]: apic_id 9, version 0, address 0xfec88000, GSI 24-47 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. SMP: Allowing 8 CPUs, 0 hotplug CPUs Allocating PCI resources starting at c2000000 (gap: c0000000:20000000) PERCPU: Allocating 45056 bytes of per cpu data NR_CPUS: 16, nr_cpu_ids: 8, nr_node_ids 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8268232 Kernel command line: ro root=LABEL=/ Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Extended CMOS year: 2000 TSC: PIT calibration matches PMTIMER. 1 loops Detected 2660.001 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes) Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes) Checking aperture... No AGP bridge found PCI-DMA: Using software bounce buffering for IO (SWIOTLB) Placing software IO TLB between 0x20000000 - 0x24000000 Memory: 32954240k/34603008k available (3824k kernel code, 1049752k absent, 598068k reserved, 1599k data, 392k init) Calibrating delay loop (skipped), value calculated using timer frequency.. 5320.00 BogoMIPS (lpj=2660001) Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM2) using mwait in idle threads. Freeing SMP alternatives: 28k freed ACPI: Core revision 20080926 Setting APIC routing to flat ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Xeon(R) CPU E5430 @ 2.66GHz stepping 06 Booting processor 1 APIC 0x4 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5319.28 BogoMIPS (lpj=2659640) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 1 CPU: Processor Core ID: 0 CPU1: Thermal monitoring enabled (TM2) x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: Intel(R) Xeon(R) CPU E5430 @ 2.66GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Booting processor 2 APIC 0x1 ip 0x6000 Initializing CPU#2 Calibrating delay using timer specific routine.. 5319.24 BogoMIPS (lpj=2659622) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU2: Thermal monitoring enabled (TM2) x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106 CPU2: Intel(R) Xeon(R) CPU E5430 @ 2.66GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#2]: passed. Booting processor 3 APIC 0x5 ip 0x6000 Initializing CPU#3 Calibrating delay using timer specific routine.. 5319.26 BogoMIPS (lpj=2659634) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 1 CPU: Processor Core ID: 1 CPU3: Thermal monitoring enabled (TM2) x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106 CPU3: Intel(R) Xeon(R) CPU E5430 @ 2.66GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#3]: passed. Booting processor 4 APIC 0x2 ip 0x6000 Initializing CPU#4 Calibrating delay using timer specific routine.. 5319.24 BogoMIPS (lpj=2659621) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 2 CPU4: Thermal monitoring enabled (TM2) x86 PAT enabled: cpu 4, old 0x7040600070406, new 0x7010600070106 CPU4: Intel(R) Xeon(R) CPU E5430 @ 2.66GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#4]: passed. Booting processor 5 APIC 0x6 ip 0x6000 Initializing CPU#5 Calibrating delay using timer specific routine.. 5319.24 BogoMIPS (lpj=2659623) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 1 CPU: Processor Core ID: 2 CPU5: Thermal monitoring enabled (TM2) x86 PAT enabled: cpu 5, old 0x7040600070406, new 0x7010600070106 CPU5: Intel(R) Xeon(R) CPU E5430 @ 2.66GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#5]: passed. Booting processor 6 APIC 0x3 ip 0x6000 Initializing CPU#6 Calibrating delay using timer specific routine.. 5319.24 BogoMIPS (lpj=2659621) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 3 CPU6: Thermal monitoring enabled (TM2) x86 PAT enabled: cpu 6, old 0x7040600070406, new 0x7010600070106 CPU6: Intel(R) Xeon(R) CPU E5430 @ 2.66GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#6]: passed. Booting processor 7 APIC 0x7 ip 0x6000 Initializing CPU#7 Calibrating delay using timer specific routine.. 5319.26 BogoMIPS (lpj=2659630) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 1 CPU: Processor Core ID: 3 CPU7: Thermal monitoring enabled (TM2) x86 PAT enabled: cpu 7, old 0x7040600070406, new 0x7010600070106 CPU7: Intel(R) Xeon(R) CPU E5430 @ 2.66GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#7]: passed. Brought up 8 CPUs Total of 8 processors activated (42554.78 BogoMIPS). net_namespace: 552 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 31 PCI: MCFG area at e0000000 reserved in E820 PCI: Using MMCONFIG at e0000000 - e1ffffff PCI: Using configuration type 1 for base access ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S5) ACPI: Using IOAPIC for interrupt routing ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:01.0: PME# supported from D0 D3hot D3cold pci 0000:00:01.0: PME# disabled pci 0000:00:05.0: PME# supported from D0 D3hot D3cold pci 0000:00:05.0: PME# disabled pci 0000:00:09.0: PME# supported from D0 D3hot D3cold pci 0000:00:09.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f] pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f] pci 0000:00:1d.2: reg 20 io port: [0x1840-0x185f] pci 0000:00:1d.3: reg 20 io port: [0x1860-0x187f] pci 0000:00:1d.7: reg 10 32bit mmio: [0xdc704000-0xdc7043ff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 pci 0000:00:1f.1: reg 10 io port: [0x00-0x07] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03] pci 0000:00:1f.1: reg 20 io port: [0x1880-0x188f] pci 0000:00:1f.2: reg 10 io port: [0x18d0-0x18d7] pci 0000:00:1f.2: reg 14 io port: [0x18c8-0x18cb] pci 0000:00:1f.2: reg 18 io port: [0x18c0-0x18c7] pci 0000:00:1f.2: reg 1c io port: [0x1894-0x1897] pci 0000:00:1f.2: reg 20 io port: [0x18a0-0x18bf] pci 0000:00:1f.2: reg 24 32bit mmio: [0xdc704400-0xdc7047ff] pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled pci 0000:00:1f.3: reg 20 io port: [0x18e0-0x18ff] pci 0000:01:00.0: reg 10 64bit mmio: [0xdc000000-0xdc1fffff] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x07ffff] pci 0000:01:00.0: supports D1 pci 0000:00:01.0: bridge 32bit mmio: [0xdc000000-0xdc1fffff] pci 0000:09:00.0: PME# supported from D0 D3hot D3cold pci 0000:09:00.0: PME# disabled pci 0000:09:00.3: PME# supported from D0 D3hot D3cold pci 0000:09:00.3: PME# disabled pci 0000:00:09.0: bridge io port: [0x2000-0x2fff] pci 0000:00:09.0: bridge 32bit mmio: [0xdc300000-0xdc4fffff] pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold pci 0000:0a:00.0: PME# disabled pci 0000:0a:02.0: PME# supported from D0 D3hot D3cold pci 0000:0a:02.0: PME# disabled pci 0000:09:00.0: bridge io port: [0x2000-0x2fff] pci 0000:09:00.0: bridge 32bit mmio: [0xdc400000-0xdc4fffff] pci 0000:0f:00.0: reg 10 32bit mmio: [0xdc420000-0xdc43ffff] pci 0000:0f:00.0: reg 14 32bit mmio: [0xdc400000-0xdc41ffff] pci 0000:0f:00.0: reg 18 io port: [0x2000-0x201f] pci 0000:0f:00.0: reg 30 32bit mmio: [0x000000-0x00ffff] pci 0000:0f:00.0: PME# supported from D0 D3hot D3cold pci 0000:0f:00.0: PME# disabled pci 0000:0f:00.1: reg 10 32bit mmio: [0xdc460000-0xdc47ffff] pci 0000:0f:00.1: reg 14 32bit mmio: [0xdc440000-0xdc45ffff] pci 0000:0f:00.1: reg 18 io port: [0x2020-0x203f] pci 0000:0f:00.1: reg 30 32bit mmio: [0x000000-0x00ffff] pci 0000:0f:00.1: PME# supported from D0 D3hot D3cold pci 0000:0f:00.1: PME# disabled pci 0000:0a:02.0: bridge io port: [0x2000-0x2fff] pci 0000:0a:02.0: bridge 32bit mmio: [0xdc400000-0xdc4fffff] pci 0000:20:05.0: reg 10 32bit mmio: [0xd8000000-0xdbffffff] pci 0000:20:05.0: reg 14 32bit mmio: [0xdc200000-0xdc23ffff] pci 0000:20:05.0: reg 18 io port: [0x3000-0x307f] pci 0000:20:05.0: supports D1 D2 pci 0000:00:1e.0: transparent bridge pci 0000:00:1e.0: bridge io port: [0x3000-0x3fff] pci 0000:00:1e.0: bridge 32bit mmio: [0xdc200000-0xdc2fffff] pci 0000:00:1e.0: bridge 64bit mmio pref: [0xd8000000-0xdbffffff] bus 00 -> node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9.BMD0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9.BMD0.BPD0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9.BMD0.BPD2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9.BMF3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 14 15) *9 ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 14 15) *12 ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 10 11 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 *10 11 14 15) SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb dca service started, version 1.4 PCI: Using ACPI for IRQ routing hpet clockevent registered HPET: 3 timers in total, 0 timers will be used for per-cpu timer hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 comparators, 64-bit 14.318180 MHz counter pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 11 devices ACPI: ACPI bus type pnp unregistered system 00:01: ioport range 0x4d0-0x4d1 has been reserved system 00:01: ioport range 0x800-0x80f has been reserved system 00:01: ioport range 0x1000-0x107f has been reserved system 00:01: ioport range 0x1180-0x11bf has been reserved system 00:01: ioport range 0xfe00-0xfe00 has been reserved system 00:01: iomem range 0xe0000000-0xefffffff has been reserved system 00:01: iomem range 0xfee00000-0xfee0ffff could not be reserved system 00:01: iomem range 0xfec00000-0xfec00fff has been reserved system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:01: iomem range 0xfec88000-0xfec88fff has been reserved system 00:01: iomem range 0xfe000000-0xfe01ffff has been reserved system 00:01: iomem range 0xfe600000-0xfe6fffff has been reserved pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: disabled pci 0000:00:01.0: MEM window: 0xdc000000-0xdc1fffff pci 0000:00:01.0: PREFETCH window: 0x000000c2000000-0x000000c20fffff pci 0000:00:05.0: PCI bridge, secondary bus 0000:05 pci 0000:00:05.0: IO window: disabled pci 0000:00:05.0: MEM window: disabled pci 0000:00:05.0: PREFETCH window: disabled pci 0000:0a:00.0: PCI bridge, secondary bus 0000:0b pci 0000:0a:00.0: IO window: disabled pci 0000:0a:00.0: MEM window: disabled pci 0000:0a:00.0: PREFETCH window: disabled pci 0000:0a:02.0: PCI bridge, secondary bus 0000:0f pci 0000:0a:02.0: IO window: 0x2000-0x2fff pci 0000:0a:02.0: MEM window: 0xdc400000-0xdc4fffff pci 0000:0a:02.0: PREFETCH window: 0x000000c2100000-0x000000c21fffff pci 0000:09:00.0: PCI bridge, secondary bus 0000:0a pci 0000:09:00.0: IO window: 0x2000-0x2fff pci 0000:09:00.0: MEM window: 0xdc400000-0xdc4fffff pci 0000:09:00.0: PREFETCH window: 0x000000c2100000-0x000000c21fffff pci 0000:09:00.3: PCI bridge, secondary bus 0000:10 pci 0000:09:00.3: IO window: disabled pci 0000:09:00.3: MEM window: disabled pci 0000:09:00.3: PREFETCH window: disabled pci 0000:00:09.0: PCI bridge, secondary bus 0000:09 pci 0000:00:09.0: IO window: 0x2000-0x2fff pci 0000:00:09.0: MEM window: 0xdc300000-0xdc4fffff pci 0000:00:09.0: PREFETCH window: 0x000000c2100000-0x000000c21fffff pci 0000:00:1c.0: PCI bridge, secondary bus 0000:1f pci 0000:00:1c.0: IO window: disabled pci 0000:00:1c.0: MEM window: disabled pci 0000:00:1c.0: PREFETCH window: disabled pci 0000:00:1e.0: PCI bridge, secondary bus 0000:20 pci 0000:00:1e.0: IO window: 0x3000-0x3fff pci 0000:00:1e.0: MEM window: 0xdc200000-0xdc2fffff pci 0000:00:1e.0: PREFETCH window: 0x000000d8000000-0x000000dbffffff pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:01.0: setting latency timer to 64 pci 0000:00:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:05.0: setting latency timer to 64 pci 0000:00:09.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:09.0: setting latency timer to 64 pci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:09:00.0: setting latency timer to 64 pci 0000:0a:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:0a:00.0: setting latency timer to 64 pci 0000:0a:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 pci 0000:0a:02.0: setting latency timer to 64 pci 0000:09:00.3: setting latency timer to 64 pci 0000:00:1c.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 bus: 00 index 0 io port: [0x00-0xffff] bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff] bus: 01 index 0 mmio: [0x0-0x0] bus: 01 index 1 mmio: [0xdc000000-0xdc1fffff] bus: 01 index 2 mmio: [0xc2000000-0xc20fffff] bus: 01 index 3 mmio: [0x0-0x0] bus: 05 index 0 mmio: [0x0-0x0] bus: 05 index 1 mmio: [0x0-0x0] bus: 05 index 2 mmio: [0x0-0x0] bus: 05 index 3 mmio: [0x0-0x0] bus: 09 index 0 io port: [0x2000-0x2fff] bus: 09 index 1 mmio: [0xdc300000-0xdc4fffff] bus: 09 index 2 mmio: [0xc2100000-0xc21fffff] bus: 09 index 3 mmio: [0x0-0x0] bus: 0a index 0 io port: [0x2000-0x2fff] bus: 0a index 1 mmio: [0xdc400000-0xdc4fffff] bus: 0a index 2 mmio: [0xc2100000-0xc21fffff] bus: 0a index 3 mmio: [0x0-0x0] bus: 0b index 0 mmio: [0x0-0x0] bus: 0b index 1 mmio: [0x0-0x0] bus: 0b index 2 mmio: [0x0-0x0] bus: 0b index 3 mmio: [0x0-0x0] bus: 0f index 0 io port: [0x2000-0x2fff] bus: 0f index 1 mmio: [0xdc400000-0xdc4fffff] bus: 0f index 2 mmio: [0xc2100000-0xc21fffff] bus: 0f index 3 mmio: [0x0-0x0] bus: 10 index 0 mmio: [0x0-0x0] bus: 10 index 1 mmio: [0x0-0x0] bus: 10 index 2 mmio: [0x0-0x0] bus: 10 index 3 mmio: [0x0-0x0] bus: 1f index 0 mmio: [0x0-0x0] bus: 1f index 1 mmio: [0x0-0x0] bus: 1f index 2 mmio: [0x0-0x0] bus: 1f index 3 mmio: [0x0-0x0] bus: 20 index 0 io port: [0x3000-0x3fff] bus: 20 index 1 mmio: [0xdc200000-0xdc2fffff] bus: 20 index 2 mmio: [0xd8000000-0xdbffffff] bus: 20 index 3 io port: [0x00-0xffff] bus: 20 index 4 mmio: [0x000000-0xffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 524288 (order: 10, 4194304 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Freeing initrd memory: 2162k freed Simple Boot Flag at 0x36 set to 0x80 Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba alg: cipher: Test 1 failed on encryption for aes-asm 00000000: 00 01 02 03 04 05 06 07 08 08 08 08 08 08 08 08 audit: initializing netlink socket (disabled) type=2000 audit(1231492835.753:1): initialized HugeTLB registered 2 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 32768 alg: No test for cipher_null (cipher_null-generic) alg: No test for digest_null (digest_null-generic) alg: No test for compress_null (compress_null-generic) alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:20:05.0: Boot video device pcieport-driver 0000:00:01.0: setting latency timer to 64 pcieport-driver 0000:00:01.0: found MSI capability pcieport-driver 0000:00:01.0: irq 767 for MSI/MSI-X pci_express 0000:00:01.0:pcie00: allocate port service pci_express 0000:00:01.0:pcie01: allocate port service pcieport-driver 0000:00:05.0: setting latency timer to 64 pcieport-driver 0000:00:05.0: found MSI capability pcieport-driver 0000:00:05.0: irq 766 for MSI/MSI-X pci_express 0000:00:05.0:pcie00: allocate port service pci_express 0000:00:05.0:pcie01: allocate port service pcieport-driver 0000:00:09.0: setting latency timer to 64 pcieport-driver 0000:00:09.0: found MSI capability pcieport-driver 0000:00:09.0: irq 765 for MSI/MSI-X pci_express 0000:00:09.0:pcie00: allocate port service pci_express 0000:00:09.0:pcie01: allocate port service pcieport-driver 0000:00:1c.0: setting latency timer to 64 pcieport-driver 0000:00:1c.0: found MSI capability pcieport-driver 0000:00:1c.0: irq 764 for MSI/MSI-X pci_express 0000:00:1c.0:pcie00: allocate port service pci_express 0000:00:1c.0:pcie02: allocate port service pci_express 0000:00:1c.0:pcie03: allocate port service pcieport-driver 0000:09:00.0: setting latency timer to 64 pci_express 0000:09:00.0:pcie11: allocate port service pcieport-driver 0000:0a:00.0: setting latency timer to 64 pcieport-driver 0000:0a:00.0: found MSI capability pcieport-driver 0000:0a:00.0: irq 763 for MSI/MSI-X pci_express 0000:0a:00.0:pcie21: allocate port service pcieport-driver 0000:0a:02.0: setting latency timer to 64 pcieport-driver 0000:0a:02.0: found MSI capability pcieport-driver 0000:0a:02.0: irq 762 for MSI/MSI-X pci_express 0000:0a:02.0:pcie21: allocate port service aer 0000:00:01.0:pcie01: AER service couldn't init device: no _OSC support aer 0000:00:05.0:pcie01: AER service couldn't init device: no _OSC support aer 0000:00:09.0:pcie01: AER service couldn't init device: no _OSC support input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] Non-volatile memory driver v1.2 intel_rng: FWH not detected Linux agpgart interface v0.103 Serial: 8250/16550 driver4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Switched to high resolution mode on CPU 7 Switched to high resolution mode on CPU 3 Switched to high resolution mode on CPU 2 Switched to high resolution mode on CPU 5 Switched to high resolution mode on CPU 4 Switched to high resolution mode on CPU 6 Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 brd: module loaded e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6 e1000e: Copyright (c) 1999-2008 Intel Corporation. e1000e 0000:0f:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 e1000e 0000:0f:00.0: setting latency timer to 64 e1000e 0000:0f:00.0: irq 761 for MSI/MSI-X 0000:0f:00.0: eth0: (PCI Express:2.5GB/s:Width x4) 00:e0:81:b3:f7:36 0000:0f:00.0: eth0: Intel(R) PRO/1000 Network Connection 0000:0f:00.0: eth0: MAC: 4, PHY: 5, PBA No: ffffff-0ff e1000e 0000:0f:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 e1000e 0000:0f:00.1: setting latency timer to 64 e1000e 0000:0f:00.1: irq 760 for MSI/MSI-X 0000:0f:00.1: eth1: (PCI Express:2.5GB/s:Width x4) 00:e0:81:b3:f7:37 0000:0f:00.1: eth1: Intel(R) PRO/1000 Network Connection 0000:0f:00.1: eth1: MAC: 4, PHY: 5, PBA No: ffffff-0ff Uniform Multi-Platform E-IDE driver Driver 'sd' needs updating - please use bus_type methods ahci 0000:00:1f.2: version 3.0 ahci 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit pm led pmp slum part ahci 0000:00:1f.2: setting latency timer to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 23 ata2: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704580 irq 23 ata3: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704600 irq 23 ata4: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704680 irq 23 ata5: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704700 irq 23 ata6: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704780 irq 23 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-8: ST3500320AS, SD15, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA ST3500320AS SD15 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk ata_piix 0000:00:1f.1: version 2.12 ata_piix 0000:00:1f.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi6 : ata_piix scsi7 : ata_piix ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1880 irq 14 ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1888 irq 15 ata8: port disabled. ignoring. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported ehci_hcd 0000:00:1d.7: irq 20, io mem 0xdc704000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001800 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 21, io base 0x00001820 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 22, io base 0x00001840 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23 uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 23, io base 0x00001860 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice rtc_cmos 00:04: RTC can wake from S4 rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs i2c /dev entries driver i801_smbus 0000:00:1f.3: PCI INT B -> GSI 23 (level, low) -> IRQ 23 usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 17 drivers/rtc/hctosys.c: unable to open rtc device (rtc) Freeing unused kernel memory: 392k freed Write protecting the kernel read-only data: 5048k kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. input: PC Speaker as /class/input/input2 Adaptec aacraid driver 1.1-5[2456]-ms aacraid 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 aacraid 0000:01:00.0: setting latency timer to 64 AAC0: kernel 5.2-0[16116] Jun 25 2008 AAC0: monitor 5.2-0[16116] AAC0: bios 5.2-0[16116] AAC0: serial 8A32108386D AAC0: Non-DASD support enabled. AAC0: 64bit support enabled. AAC0: 64 Bit DAC enabled scsi8 : aacraid scsi 8:0:0:0: Direct-Access Adaptec Mem3 V1.0 PQ: 0 ANSI: 2 sd 8:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16). sd 8:0:0:0: [sdb] 13457403904 512-byte hardware sectors: (6.89 TB/6.26 TiB) sd 8:0:0:0: [sdb] Write Protect is off sd 8:0:0:0: [sdb] Mode Sense: 06 00 10 00 sd 8:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 8:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16). sd 8:0:0:0: [sdb] 13457403904 512-byte hardware sectors: (6.89 TB/6.26 TiB) sd 8:0:0:0: [sdb] Write Protect is off sd 8:0:0:0: [sdb] Mode Sense: 06 00 10 00 sd 8:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sdb: unknown partition table sd 8:0:0:0: [sdb] Attached SCSI removable disk scsi 8:1:0:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:1:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:2:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:3:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:4:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:5:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:6:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:7:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:8:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:9:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:10:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:11:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:12:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:13:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:14:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:15:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:16:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:17:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:18:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:19:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:20:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:21:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:22:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 scsi 8:1:23:0: Direct-Access SEAGATE ST3300655SS S527 PQ: 1 ANSI: 5 md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com device-mapper: multipath: version 1.0.5 loaded EXT3 FS on sda3, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. XFS mounting filesystem sdb Ending clean XFS mount for filesystem: sdb Adding 16779884k swap on /dev/sda2. Priority:-1 extents:1 across:16779884k e1000e 0000:0f:00.0: irq 761 for MSI/MSI-X e1000e 0000:0f:00.0: irq 761 for MSI/MSI-X 0000:0f:00.0: eth0: Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX e1000e 0000:0f:00.1: irq 760 for MSI/MSI-X e1000e 0000:0f:00.1: irq 760 for MSI/MSI-X 0000:0f:00.1: eth1: Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX warning: `dbus-daemon' uses 32-bit capabilities (legacy support in use) RPC: Registered udp transport module. RPC: Registered tcp transport module.
Dmidecode:
# dmidecode 2.7 SMBIOS 2.5 present. 61 structures occupying 1876 bytes. Table at 0xBFF60000.
Handle 0x0000, DMI type 0, 24 bytes. BIOS Information Vendor: Phoenix Technologies LTD Version: V1.04B Release Date: 10/21/2008 Address: 0xE4CD0 Runtime Size: 111408 bytes ROM Size: 1024 kB Characteristics: PCI is supported PNP is supported APM is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported BIOS ROM is socketed EDD is supported ACPI is supported USB legacy is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported BIOS Revision: 1.3
Handle 0x0001, DMI type 1, 27 bytes. System Information Manufacturer: Empty Product Name: Empty Version: Empty Serial Number: Empty UUID: 00000000-0000-0000-0000-F0AB0C00C04D Wake-up Type: Power Switch SKU Number: Not Specified Family: Not Specified
Handle 0x0002, DMI type 2, 8 bytes. Base Board Information Manufacturer: TYAN Product Name: S5397 Version: 1.0 Serial Number: 0123456789
Handle 0x0003, DMI type 3, 17 bytes. Chassis Information Manufacturer: Empty Type: Other Lock: Not Present Version: Empty Serial Number: Empty Asset Tag: Empty Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: None OEM Information: 0x00000000
Handle 0x0004, DMI type 4, 40 bytes. Processor Information Socket Designation: LGA771 Type: Central Processor Family: Pentium II Xeon Manufacturer: Intel ID: 76 06 01 00 FF FB EB BF Signature: Type 0, Family 6, Model 23, Stepping 6 Flags: FPU (Floating-point unit on-chip) VME (Virtual mode extension) DE (Debugging extension) PSE (Page size extension) TSC (Time stamp counter) MSR (Model specific registers) PAE (Physical address extension) MCE (Machine check exception) CX8 (CMPXCHG8 instruction supported) APIC (On-chip APIC hardware supported) SEP (Fast system call) MTRR (Memory type range registers) PGE (Page global enable) MCA (Machine check architecture) CMOV (Conditional move instruction supported) PAT (Page attribute table) PSE-36 (36-bit page size extension) CLFSH (CLFLUSH instruction supported) DS (Debug store) ACPI (ACPI supported) MMX (MMX technology supported) FXSR (Fast floating-point save and restore) SSE (Streaming SIMD extensions) SSE2 (Streaming SIMD extensions 2) SS (Self-snoop) HTT (Hyper-threading technology) TM (Thermal monitor supported) PBE (Pending break enabled) Version: Voltage: 1.2 V External Clock: Unknown Max Speed: 3800 MHz Current Speed: 2660 MHz Status: Populated, Enabled Upgrade: <OUT OF SPEC> L1 Cache Handle: 0x0006 L2 Cache Handle: 0x0007 L3 Cache Handle: Not Provided Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0005, DMI type 4, 40 bytes. Processor Information Socket Designation: . Type: Central Processor Family: Pentium II Xeon Manufacturer: . ID: 76 06 01 00 FF FB EB BF Signature: Type 0, Family 6, Model 23, Stepping 6 Flags: FPU (Floating-point unit on-chip) VME (Virtual mode extension) DE (Debugging extension) PSE (Page size extension) TSC (Time stamp counter) MSR (Model specific registers) PAE (Physical address extension) MCE (Machine check exception) CX8 (CMPXCHG8 instruction supported) APIC (On-chip APIC hardware supported) SEP (Fast system call) MTRR (Memory type range registers) PGE (Page global enable) MCA (Machine check architecture) CMOV (Conditional move instruction supported) PAT (Page attribute table) PSE-36 (36-bit page size extension) CLFSH (CLFLUSH instruction supported) DS (Debug store) ACPI (ACPI supported) MMX (MMX technology supported) FXSR (Fast floating-point save and restore) SSE (Streaming SIMD extensions) SSE2 (Streaming SIMD extensions 2) SS (Self-snoop) HTT (Hyper-threading technology) TM (Thermal monitor supported) PBE (Pending break enabled) Version: X Voltage: 1.2 V External Clock: Unknown Max Speed: 3800 MHz Current Speed: 2660 MHz Status: Populated, Enabled Upgrade: <OUT OF SPEC> L1 Cache Handle: 0x0008 L2 Cache Handle: 0x0009 L3 Cache Handle: Not Provided Serial Number: Not Specified Asset Tag: <BAD INDEX> Part Number: <BAD INDEX>
Handle 0x4C02, DMI type 2, 2 bytes. Base Board Information
Handle 0x0007, DMI type 7, 19 bytes. Cache Information Socket Designation: L2 Cache Configuration: Enabled, Socketed, Level 2 Operational Mode: Write Back Location: Internal Installed Size: 12288 KB Maximum Size: 8192 KB Supported SRAM Types: Burst Pipeline Burst Asynchronous Installed SRAM Type: Burst Speed: Unknown Error Correction Type: Unknown System Type: Unknown Associativity: Unknown
Handle 0x0008, DMI type 7, 19 bytes. Cache Information Socket Designation: L1 Cache Configuration: Enabled, Socketed, Level 1 Operational Mode: Write Back Location: Internal Installed Size: 16 KB Maximum Size: 16 KB Supported SRAM Types: Burst Pipeline Burst Asynchronous Installed SRAM Type: Asynchronous Speed: Unknown Error Correction Type: Unknown System Type: Unknown Associativity: Unknown
Handle 0x0009, DMI type 7, 19 bytes. Cache Information Socket Designation: L2 Cache Configuration: Enabled, Socketed, Level 2 Operational Mode: Write Back Location: Internal Installed Size: 12288 KB Maximum Size: 8192 KB Supported SRAM Types: Burst Pipeline Burst Asynchronous Installed SRAM Type: Burst Speed: Unknown Error Correction Type: Unknown System Type: Unknown Associativity: Unknown
Handle 0x000A, DMI type 8, 9 bytes. Port Connector Information Internal Reference Designator: J4 Internal Connector Type: 9 Pin Dual Inline (pin 10 cut) External Reference Designator: COM 1 External Connector Type: DB-9 male Port Type: Serial Port 16550A Compatible
Handle 0x000B, DMI type 8, 9 bytes. Port Connector Information Internal Reference Designator: J20 Internal Connector Type: 9 Pin Dual Inline (pin 10 cut) External Reference Designator: COM 2 External Connector Type: DB-9 male Port Type: Serial Port 16550A Compatible
Handle 0x000C, DMI type 8, 9 bytes. Port Connector Information Internal Reference Designator: J1 Internal Connector Type: None External Reference Designator: Keyboard External Connector Type: Circular DIN-8 male Port Type: Keyboard Port
Handle 0x000D, DMI type 8, 9 bytes. Port Connector Information Internal Reference Designator: J1 Internal Connector Type: None External Reference Designator: PS/2 Mouse External Connector Type: Circular DIN-8 male Port Type: Keyboard Port
Handle 0x000E, DMI type 9, 13 bytes. System Slot Information Designation: PCI/33 Slot #1 - J1B1 Type: 32-bit PCI Current Usage: Available Length: Long ID: 1 Characteristics: 5.0 V is provided 3.3 V is provided
Handle 0x000F, DMI type 9, 13 bytes. System Slot Information Designation: PCIE Slot #2 - J2B1 Type: 32-bit PCI Express Current Usage: Available Length: Long Characteristics: 5.0 V is provided 3.3 V is provided
Handle 0x0010, DMI type 9, 13 bytes. System Slot Information Designation: PCIE Slot #3 - J2B2 Type: 32-bit PCI Express Current Usage: Available Length: Long Characteristics: 5.0 V is provided 3.3 V is provided
Handle 0x0011, DMI type 9, 13 bytes. System Slot Information Designation: PCIE Slot #4 - J3B3 Type: 32-bit PCI Express Current Usage: Available Length: Long Characteristics: 5.0 V is provided 3.3 V is provided
Handle 0x0012, DMI type 9, 13 bytes. System Slot Information Designation: PCIE Slot #5 - J3B2 Type: 32-bit PCI-X Current Usage: Available Length: Long ID: 5 Characteristics: 5.0 V is provided 3.3 V is provided
Handle 0x0013, DMI type 9, 13 bytes. System Slot Information Designation: PCIE Slot #6 - J4B1 Type: 32-bit PCI Express Current Usage: Available Length: Long Characteristics: 5.0 V is provided 3.3 V is provided
Handle 0x0014, DMI type 10, 6 bytes. On Board Device Information Type: Sound Status: Disabled Description: RealTek
Handle 0x0015, DMI type 11, 5 bytes. OEM Strings String 1: 0 String 2: 0 String 3: .........................
Handle 0x0016, DMI type 15, 29 bytes. System Event Log Area Length: 32 bytes Header Start Offset: 0x0000 Header Length: 16 bytes Data Start Offset: 0x0010 Access Method: General-purpose non-volatile data functions Access Address: 0x0000 Status: Valid, Not Full Change Token: 0x000000E5 Header Format: Type 1 Supported Log Type Descriptors: 3 Descriptor 1: POST error Data Format 1: POST results bitmap Descriptor 2: Single-bit ECC memory error Data Format 2: Multiple-event Descriptor 3: Multi-bit ECC memory error Data Format 3: Multiple-event
Handle 0x0017, DMI type 16, 15 bytes. Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 64 GB Error Information Handle: Not Provided Number Of Devices: 4
Handle 0x0018, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM1 Bank Locator: DIMM1 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0019, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM2 Bank Locator: DIMM2 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x001A, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM3 Bank Locator: DIMM3 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x001B, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM4 Bank Locator: DIMM4 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x001C, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM5 Bank Locator: DIMM5 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x001D, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM6 Bank Locator: DIMM6 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x001E, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM7 Bank Locator: DIMM7 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x001F, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM8 Bank Locator: DIMM8 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0020, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM9 Bank Locator: DIMM9 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0021, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM10 Bank Locator: DIMM10 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0022, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM11 Bank Locator: DIMM11 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0023, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM12 Bank Locator: DIMM12 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0024, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM13 Bank Locator: DIMM13 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0025, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM14 Bank Locator: DIMM14 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0026, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM15 Bank Locator: DIMM15 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0027, DMI type 17, 27 bytes. Memory Device Array Handle: 0x0017 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: <OUT OF SPEC> Set: 1 Locator: DIMM16 Bank Locator: DIMM16 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified
Handle 0x0028, DMI type 19, 15 bytes. Memory Array Mapped Address Starting Address: 0x00000000000 Ending Address: 0x007FFFFFFFF Range Size: 32 GB Physical Array Handle: 0x0017 Partition Width: 0
Handle 0x0029, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00000000000 Ending Address: 0x0007FFFFFFF Range Size: 2 GB Physical Device Handle: 0x0018 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x002A, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00080000000 Ending Address: 0x000FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x0019 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x002B, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00100000000 Ending Address: 0x0017FFFFFFF Range Size: 2 GB Physical Device Handle: 0x001A Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x002C, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00180000000 Ending Address: 0x001FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x001B Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x002D, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00200000000 Ending Address: 0x0027FFFFFFF Range Size: 2 GB Physical Device Handle: 0x001C Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x002E, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00280000000 Ending Address: 0x002FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x001D Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x002F, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00300000000 Ending Address: 0x0037FFFFFFF Range Size: 2 GB Physical Device Handle: 0x001E Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0030, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00380000000 Ending Address: 0x003FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x001F Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0031, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00400000000 Ending Address: 0x0047FFFFFFF Range Size: 2 GB Physical Device Handle: 0x0020 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0032, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00480000000 Ending Address: 0x004FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x0021 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0033, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00500000000 Ending Address: 0x0057FFFFFFF Range Size: 2 GB Physical Device Handle: 0x0022 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0034, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00580000000 Ending Address: 0x005FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x0023 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0035, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00600000000 Ending Address: 0x0067FFFFFFF Range Size: 2 GB Physical Device Handle: 0x0024 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0036, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00680000000 Ending Address: 0x006FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x0025 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0037, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00700000000 Ending Address: 0x0077FFFFFFF Range Size: 2 GB Physical Device Handle: 0x0026 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0038, DMI type 20, 19 bytes. Memory Device Mapped Address Starting Address: 0x00780000000 Ending Address: 0x007FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x0027 Memory Array Mapped Address Handle: 0x0028 Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown
Handle 0x0039, DMI type 23, 13 bytes. System Reset Status: Enabled Watchdog Timer: Present Boot Option: Do Not Reboot Boot Option On Limit: Do Not Reboot Reset Count: Unknown Reset Limit: Unknown Timer Interval: Unknown Timeout: Unknown
Handle 0x003A, DMI type 32, 20 bytes. System Boot Information Status: <OUT OF SPEC>
Handle 0x003B, DMI type 38, 18 bytes. IPMI Device Information Interface Type: Unknown Specification Version: 0.0 I2C Slave Address: 0x00 NV Storage Device: Not Present Base Address: 0x0000000000000000 (Memory-mapped) Register Spacing: Successive Byte Boundaries Interrupt Polarity: Active Low Interrupt Trigger Mode: Edge
Handle 0x003C, DMI type 127, 4 bytes. End Of Table
Doug Bazarnic
-- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |