lkml.org 
[lkml]   [2009]   [Jan]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: e1000 tx Unit hang on 2.6.28 and patch that works...
    On Fri, Jan 9, 2009 at 1:47 PM, Doug Bazarnic <kernel@bazarnic.net> wrote:
    > Asus P5k, Intel Q9450, 8gb ram, x86_64, running 2.6.28. The on board eth0
    > atl1 never has a problem, only eth1 intel e1000, plugged into a pci slot.
    >
    > On a couple of machines, the way I got it to stop, was to use 8.0.6 intel
    > e1000 driver with the patch below. (works on same hardware, running 2.6.27
    > kernels)
    > I can't remember where I downloaded this patch from, but I haven't had an
    > issue yet with it.
    >
    > [root@web6 SCRIPTS]# cat e1000-8-0-6-stepfix.patch
    >>diff -up e1000-8-0-6base/src/e1000_main.c
    > e1000-8-0-6stepfix/src/e1000_main.c
    >>--- e1000-8-0-6base/src/e1000_main.c 2008-10-29 17:38:38.000000000 -0700
    >>+++ e1000-8-0-6stepfix/src/e1000_main.c 2008-10-29 17:43:52.000000000 -0700
    >>@@ -65,7 +65,7 @@ static char e1000_driver_string[] = "Int
    >>
    >> #define DRV_HW_PERF
    >>
    >>-#define DRV_VERSION "8.0.6" DRV_NAPI DRV_DEBUG DRV_HW_PERF
    >>+#define DRV_VERSION "8.0.6a" DRV_NAPI DRV_DEBUG DRV_HW_PERF
    >> const char e1000_driver_version[] = DRV_VERSION;
    >> static const char e1000_copyright[] = "Copyright (c) 1999-2008 Intel
    > Corporation.";
    >>
    >>@@ -2364,8 +2364,8 @@ link_up:
    >> if (!netif_carrier_ok(netdev)) {
    >> for (i = 0 ; i < adapter->num_tx_queues ; i++) {
    >> tx_ring = &adapter->tx_ring[i];
    >>- tx_pending |= (E1000_DESC_UNUSED(tx_ring) + 1 <
    >>-
    > tx_ring->count);
    >>+ tx_pending |= (E1000_DESC_UNUSED(tx_ring) +
    >>+ tx_ring->step < tx_ring->count);
    >> }
    >> if (tx_pending) {
    >> /* We've lost link, so the controller stops DMA,
    >>@@ -2892,7 +2892,7 @@ static int __e1000_maybe_stop_tx(struct
    >>
    >> /* We need to check again in a case another CPU has just
    >> * made room available. */
    >>- if (likely(E1000_DESC_UNUSED(tx_ring) < size))
    >>+ if (likely(E1000_DESC_UNUSED(tx_ring) < ((size) * tx_ring->step)))
    >> return -EBUSY;
    >>
    >> /* A reprieve! */
    >>@@ -2909,7 +2909,7 @@ static int __e1000_maybe_stop_tx(struct
    >> static int e1000_maybe_stop_tx(struct net_device *netdev,
    >> struct e1000_tx_ring *tx_ring, int size)
    >> {
    >>- if (likely(E1000_DESC_UNUSED(tx_ring) >= size))
    >>+ if (likely(E1000_DESC_UNUSED(tx_ring) >= ((size) * tx_ring->step)))
    >> return 0;
    >> return __e1000_maybe_stop_tx(netdev, tx_ring, size);
    >> }
    >
    > ---------------------------------
    >
    > This has been an ongoing problem on over 20 identical machines.
    >
    > Jan 7 13:26:41 web2 kernel: e1000: eth1: e1000_clean_tx_irq: Detected Tx
    > Unit Hang
    > Jan 7 13:26:41 web2 kernel: Tx Queue <0>
    > Jan 7 13:26:41 web2 kernel: TDH <2a>
    > Jan 7 13:26:41 web2 kernel: TDT <2d>
    > Jan 7 13:26:41 web2 kernel: next_to_use <2d>
    > Jan 7 13:26:41 web2 kernel: next_to_clean <2a>
    > Jan 7 13:26:41 web2 kernel: buffer_info[next_to_clean]
    > Jan 7 13:26:41 web2 kernel: time_stamp <103105c76>
    > Jan 7 13:26:41 web2 kernel: next_to_watch <2a>
    > Jan 7 13:26:41 web2 kernel: jiffies <103106770>
    > Jan 7 13:26:41 web2 kernel: next_to_watch.status <0>
    > Jan 7 13:26:43 web2 kernel: e1000: eth1: e1000_clean_tx_irq: Detected Tx
    > Unit Hang
    > Jan 7 13:26:43 web2 kernel: Tx Queue <0>
    > Jan 7 13:26:43 web2 kernel: TDH <2a>
    > Jan 7 13:26:43 web2 kernel: TDT <2d>
    > Jan 7 13:26:43 web2 kernel: next_to_use <2d>
    > Jan 7 13:26:43 web2 kernel: next_to_clean <2a>
    > Jan 7 13:26:43 web2 kernel: buffer_info[next_to_clean]
    > Jan 7 13:26:43 web2 kernel: time_stamp <103105c76>
    > Jan 7 13:26:43 web2 kernel: next_to_watch <2a>
    > Jan 7 13:26:43 web2 kernel: jiffies <103106f41>
    > Jan 7 13:26:43 web2 kernel: next_to_watch.status <0>
    > Jan 7 13:26:45 web2 kernel: e1000: eth1: e1000_clean_tx_irq: Detected Tx
    > Unit Hang
    > Jan 7 13:26:45 web2 kernel: Tx Queue <0>
    > Jan 7 13:26:45 web2 kernel: TDH <2a>
    > Jan 7 13:26:45 web2 kernel: TDT <2d>
    > Jan 7 13:26:45 web2 kernel: next_to_use <2d>
    > Jan 7 13:26:45 web2 kernel: next_to_clean <2a>
    > Jan 7 13:26:45 web2 kernel: buffer_info[next_to_clean]
    > Jan 7 13:26:45 web2 kernel: time_stamp <103105c76>
    > Jan 7 13:26:45 web2 kernel: next_to_watch <2a>
    > Jan 7 13:26:45 web2 kernel: jiffies <103107711>
    > Jan 7 13:26:45 web2 kernel: next_to_watch.status <0>
    > Jan 7 13:26:47 web2 kernel: ------------[ cut here ]------------
    > Jan 7 13:26:47 web2 kernel: WARNING: at net/sched/sch_generic.c:226
    > dev_watchdog+0x206/0x220()
    > Jan 7 13:26:47 web2 kernel: NETDEV WATCHDOG: eth1 (e1000): transmit timed
    > out
    > Jan 7 13:26:47 web2 kernel: Modules linked in: nfs lockd nfs_acl sunrpc
    > dm_mirror dm_region_hash dm_log dm_multipath dm_mod serio_raw e1000
    > pata_jmicron pcspkr
    > Jan 7 13:26:47 web2 kernel: Pid: 0, comm: swapper Not tainted 2.6.28 #1
    > Jan 7 13:26:47 web2 kernel: Call Trace:
    > Jan 7 13:26:47 web2 kernel: <IRQ> [<ffffffff802361fc>]
    > warn_slowpath+0x10c/0x150
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8022f4c1>]
    > enqueue_task_fair+0xf1/0x110
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8022c217>] source_load+0x37/0x70
    > Jan 7 13:26:47 web2 kernel: [<ffffffff803c9a6a>] __next_cpu+0x1a/0x30
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8022d99c>]
    > find_busiest_group+0x18c/0x820
    > Jan 7 13:26:47 web2 kernel: [<ffffffff802116c9>] read_tsc+0x9/0x20
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8024fc71>] getnstimeofday+0x41/0xc0
    > Jan 7 13:26:47 web2 kernel: [<ffffffff803cf20e>] strlcpy+0x4e/0x80
    > Jan 7 13:26:47 web2 kernel: [<ffffffff80532cd6>] dev_watchdog+0x206/0x220
    > Jan 7 13:26:47 web2 kernel: [<ffffffff802116c9>] read_tsc+0x9/0x20
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8024fc71>] getnstimeofday+0x41/0xc0
    > Jan 7 13:26:47 web2 kernel: [<ffffffff80532ad0>] dev_watchdog+0x0/0x220
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8023fadf>]
    > run_timer_softirq+0x15f/0x1c0
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8021b165>]
    > lapic_next_event+0x15/0x20
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8023b40c>] __do_softirq+0x9c/0x170
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8020c87c>] call_softirq+0x1c/0x30
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8020d975>] do_softirq+0x35/0x70
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8021bb05>]
    > smp_apic_timer_interrupt+0x85/0xd0
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8020c2cb>]
    > apic_timer_interrupt+0x6b/0x70
    > Jan 7 13:26:47 web2 kernel: <EOI> [<ffffffff80212511>]
    > mwait_idle+0x41/0x50
    > Jan 7 13:26:47 web2 kernel: [<ffffffff8020a2da>] cpu_idle+0x3a/0x70
    > Jan 7 13:26:47 web2 kernel: ---[ end trace 06fe492fa8302a12 ]---
    > Jan 7 13:26:50 web2 kernel: e1000: eth1: e1000_watchdog: NIC Link is Up
    > 1000 Mbps Full Duplex, Flow Control: RX/TX
    >
    >
    >
    > 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM
    > Controller (rev 02)
    > Subsystem: ASUSTeK Computer Inc. Unknown device 8276
    > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort+ >SERR- <PERR-
    > Latency: 0
    > Capabilities: [e0] Vendor Specific Information
    >
    > 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express
    > Integrated Graphics Controller (rev 02) (prog-if 00 [VGA])
    > Subsystem: ASUSTeK Computer Inc. Unknown device 8276
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    > Interrupt: pin A routed to IRQ 11
    > Region 0: Memory at fe800000 (32-bit, non-prefetchable) [size=512K]
    > Region 1: I/O ports at cc00 [size=8]
    > Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
    > Region 3: Memory at fe700000 (32-bit, non-prefetchable) [size=1M]
    > Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0
    > Enable-
    > Address: 00000000 Data: 0000
    > Capabilities: [d0] Power Management version 2
    > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
    > PME(D0-,D1-,D2-,D3hot-,D3cold-)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > 00:02.1 Display controller: Intel Corporation 82G33/G31 Express Integrated
    > Graphics Controller (rev 02)
    > Subsystem: ASUSTeK Computer Inc. Unknown device 8276
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    > Region 0: Memory at fe880000 (32-bit, non-prefetchable) [size=512K]
    > Capabilities: [d0] Power Management version 2
    > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
    > PME(D0-,D1-,D2-,D3hot-,D3cold-)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
    > 1 (rev 02) (prog-if 00 [Normal decode])
    > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR+ FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0, Cache Line Size: 32 bytes
    > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
    > I/O behind bridge: 0000f000-00000fff
    > Memory behind bridge: fff00000-000fffff
    > Prefetchable memory behind bridge: 00000000fdf00000-00000000fdf00000
    > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort+ <SERR- <PERR-
    > BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    > Capabilities: [40] Express Root Port (Slot+) IRQ 0
    > Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    > ExtTag-
    > Device: Latency L0s <64ns, L1 <1us
    > Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    > Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    > Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
    > Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1
    > Link: Latency L0s <1us, L1 <4us
    > Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
    > Link: Speed 2.5Gb/s, Width x0
    > Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
    > Surpise+
    > Slot: Number 0, PowerLimit 10.000000
    > Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
    > Slot: AttnInd Unknown, PwrInd Unknown, Power-
    > Root: Correctable- Non-Fatal- Fatal- PME-
    > Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
    > Enable+
    > Address: fee0f00c Data: 4159
    > Capabilities: [90] #0d [0000]
    > Capabilities: [a0] Power Management version 2
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    > PME(D0+,D1-,D2-,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    > Capabilities: [100] Virtual Channel
    > Capabilities: [180] Unknown (5)
    >
    > 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
    > 5 (rev 02) (prog-if 00 [Normal decode])
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR+ FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0, Cache Line Size: 32 bytes
    > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
    > I/O behind bridge: 0000d000-0000dfff
    > Memory behind bridge: fea00000-feafffff
    > Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- <SERR- <PERR-
    > BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    > Capabilities: [40] Express Root Port (Slot+) IRQ 0
    > Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    > ExtTag-
    > Device: Latency L0s <64ns, L1 <1us
    > Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    > Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    > Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
    > Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
    > Link: Latency L0s <256ns, L1 <4us
    > Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
    > Link: Speed 2.5Gb/s, Width x1
    > Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
    > Surpise+
    > Slot: Number 0, PowerLimit 10.000000
    > Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
    > Slot: AttnInd Unknown, PwrInd Unknown, Power-
    > Root: Correctable- Non-Fatal- Fatal- PME-
    > Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
    > Enable+
    > Address: fee0f00c Data: 4161
    > Capabilities: [90] #0d [0000]
    > Capabilities: [a0] Power Management version 2
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    > PME(D0+,D1-,D2-,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    > Capabilities: [100] Virtual Channel
    > Capabilities: [180] Unknown (5)
    >
    > 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
    > 6 (rev 02) (prog-if 00 [Normal decode])
    > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR+ FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0, Cache Line Size: 32 bytes
    > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    > I/O behind bridge: 0000f000-00000fff
    > Memory behind bridge: fe900000-fe9fffff
    > Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort+ <SERR- <PERR-
    > BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    > Capabilities: [40] Express Root Port (Slot+) IRQ 0
    > Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    > ExtTag-
    > Device: Latency L0s <64ns, L1 <1us
    > Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    > Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    > Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
    > Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 6
    > Link: Latency L0s <256ns, L1 <4us
    > Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
    > Link: Speed 2.5Gb/s, Width x1
    > Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
    > Surpise+
    > Slot: Number 0, PowerLimit 10.000000
    > Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
    > Slot: AttnInd Unknown, PwrInd Unknown, Power-
    > Root: Correctable- Non-Fatal- Fatal- PME-
    > Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
    > Enable+
    > Address: fee0f00c Data: 4169
    > Capabilities: [90] #0d [0000]
    > Capabilities: [a0] Power Management version 2
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    > PME(D0+,D1-,D2-,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    > Capabilities: [100] Virtual Channel
    > Capabilities: [180] Unknown (5)
    >
    > 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) (prog-if 01
    > [Subtractive decode])
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR+ FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    > Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
    > I/O behind bridge: 0000e000-0000efff
    > Memory behind bridge: feb00000-febfffff
    > Prefetchable memory behind bridge: 00000000f0000000-00000000f0000000
    > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > <TAbort- <MAbort+ <SERR- <PERR-
    > BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    > Capabilities: [50] #0d [0000]
    >
    > 00:1f.0 ISA bridge: Intel Corporation 82801IB (ICH9) LPC Interface
    > Controller (rev 02)
    > Subsystem: ASUSTeK Computer Inc. Unknown device 8277
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    > Capabilities: [e0] Vendor Specific Information
    >
    > 00:1f.2 IDE interface: Intel Corporation 82801IB (ICH9) 2 port SATA IDE
    > Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
    > Subsystem: ASUSTeK Computer Inc. Unknown device 8277
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    > Interrupt: pin B routed to IRQ 22
    > Region 0: I/O ports at b880 [size=8]
    > Region 1: I/O ports at b800 [size=4]
    > Region 2: I/O ports at b480 [size=8]
    > Region 3: I/O ports at b400 [size=4]
    > Region 4: I/O ports at b080 [size=16]
    > Region 5: I/O ports at b000 [size=16]
    > Capabilities: [70] Power Management version 3
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    > PME(D0-,D1-,D2-,D3hot-,D3cold-)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    > Capabilities: [b0] Vendor Specific Information
    >
    > 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev
    > 02)
    > Subsystem: ASUSTeK Computer Inc. Unknown device 8277
    > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Interrupt: pin C routed to IRQ 5
    > Region 0: Memory at fe6fbc00 (64-bit, non-prefetchable) [size=256]
    > Region 4: I/O ports at 0400 [size=32]
    >
    > 00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA
    > IDE Controller (rev 02) (prog-if 85 [Master SecO PriO])
    > Subsystem: ASUSTeK Computer Inc. Unknown device 8277
    > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    > Interrupt: pin B routed to IRQ 22
    > Region 0: I/O ports at c880 [size=8]
    > Region 1: I/O ports at c800 [size=4]
    > Region 2: I/O ports at c480 [size=8]
    > Region 3: I/O ports at c400 [size=4]
    > Region 4: I/O ports at c080 [size=16]
    > Region 5: I/O ports at c000 [size=16]
    > Capabilities: [70] Power Management version 3
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    > PME(D0-,D1-,D2-,D3hot-,D3cold-)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    > Capabilities: [b0] Vendor Specific Information
    >
    > 01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet
    > Adapter (rev b0)
    > Subsystem: ASUSTeK Computer Inc. Unknown device 8226
    > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0, Cache Line Size: 32 bytes
    > Interrupt: pin A routed to IRQ 27
    > Region 0: Memory at fe9c0000 (64-bit, non-prefetchable) [size=256K]
    > Expansion ROM at fe9a0000 [disabled] [size=128K]
    > Capabilities: [40] Power Management version 2
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    > PME(D0-,D1-,D2-,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    > Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/0
    > Enable+
    > Address: 00000000fee0200c Data: 4179
    > Capabilities: [58] Express Endpoint IRQ 0
    > Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    > ExtTag-
    > Device: Latency L0s <4us, L1 unlimited
    > Device: AtnBtn+ AtnInd+ PwrInd+
    > Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    > Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    > Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
    > Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
    > Link: Latency L0s unlimited, L1 unlimited
    > Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
    > Link: Speed 2.5Gb/s, Width x1
    > Capabilities: [100] Advanced Error Reporting
    >
    > 02:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI
    > Controller (rev 03) (prog-if 01 [AHCI 1.0])
    > Subsystem: ASUSTeK Computer Inc. Unknown device 824f
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0, Cache Line Size: 32 bytes
    > Interrupt: pin A routed to IRQ 16
    > Region 5: Memory at feafe000 (32-bit, non-prefetchable) [size=8K]
    > Expansion ROM at feae0000 [disabled] [size=64K]
    > Capabilities: [68] Power Management version 2
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    > PME(D0-,D1-,D2-,D3hot+,D3cold-)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    > Capabilities: [50] Express Legacy Endpoint IRQ 1
    > Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    > ExtTag-
    > Device: Latency L0s <64ns, L1 <1us
    > Device: AtnBtn- AtnInd- PwrInd-
    > Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    > Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    > Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
    > Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
    > Link: Latency L0s <1us, L1 <16us
    > Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
    > Link: Speed 2.5Gb/s, Width x1
    >
    > 02:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI
    > Controller (rev 03) (prog-if 85 [Master SecO PriO])
    > Subsystem: ASUSTeK Computer Inc. Unknown device 824f
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    > Interrupt: pin B routed to IRQ 17
    > Region 0: I/O ports at dc00 [size=8]
    > Region 1: I/O ports at d880 [size=4]
    > Region 2: I/O ports at d800 [size=8]
    > Region 3: I/O ports at d480 [size=4]
    > Region 4: I/O ports at d400 [size=16]
    > Capabilities: [68] Power Management version 2
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    > PME(D0-,D1-,D2-,D3hot-,D3cold-)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > 04:01.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet
    > Controller (rev 05)
    > Subsystem: Intel Corporation PRO/1000 GT Desktop Adapter
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
    > Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    > <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 64 (63750ns min), Cache Line Size: 32 bytes
    > Interrupt: pin A routed to IRQ 17
    > Region 0: Memory at febe0000 (32-bit, non-prefetchable) [size=128K]
    > Region 1: Memory at febc0000 (32-bit, non-prefetchable) [size=128K]
    > Region 2: I/O ports at ec00 [size=64]
    > Expansion ROM at f0000000 [disabled] [size=128K]
    > Capabilities: [dc] Power Management version 2
    > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
    > PME(D0+,D1-,D2-,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=1 PME-
    > Capabilities: [e4] PCI-X non-bridge device
    > Command: DPERE- ERO+ RBC=512 OST=1
    > Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple
    > DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
    >
    >
    > Doug Bazarnic
    >
    > --

    Adding netdev and e1000-devel ml's.


    --
    Cheers,
    Jeff


    \
     
     \ /
      Last update: 2009-01-12 19:31    [W:0.078 / U:59.808 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site