lkml.org 
[lkml]   [2008]   [Sep]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] lld busy status exporting interface
Hi Andrew,
(and James, Jens, please let us know your opinions on the possible
changes described below)

Andrew Morton wrote:
> On Fri, 19 Sep 2008 19:11:22 -0400 (EDT)
> Kiyoshi Ueda <k-ueda@ct.jp.nec.com> wrote:
>
>>> Back in the days when we first did the backing_dev_info.congested_fn()
>>> logic it was decided that there basically was no single place in which
>>> the congested state could be stored.
>>>
>>> So we ended up deciding that whenever a caller wants to know a
>>> backing_dev's congested status, it has to call in to the
>>> ->congested_fn() and that congested_fn would then call down into all
>>> the constituent low-level drivers/queues/etc asking each one if it is
>>> congested.
>> bdi_lld_congested() also does that using bdi_congested(), which calls
>> ->congested_fn().
>> And only real device drivers (e.g. scsi, ide) set/clear the flag.
>> Stacking drivers like request-based dm don't.
>
> umm, OK, that should work.
>
>> So stacking drivers always check the BDI_lld_congested flag of
>> the bottom device of the device stack.
>
> How does a stacking driver know that the backing_device which it is
> looking at is a "lowest level" device?
>
> I don't think it does - only the code which implements that device
> knows this, so the stacking driver has to call into that device's
> congested_fn(), yes?

Yes. So the stacking driver calls bdi_congested, which calls
the underlying device's congested_fn if exists, and eventually
checks the bottom device's congestion state.
Translation of multiple devices' congestion status is done by
the congested_fn of the stacking device.
E.g. dm-multipath returns 'not congested' if any of its paths are not
congested.

> In which case one wonders why the state was stored in the
> backing_dev_info at all. Why not store it in the device-private data
> to avoid confusion and abuse?

It should be possible.
We've just followed the existing scheme of BDI_{read,write}congested
because of their similarity.

I would like to know which part of the patch was your concern:
1) Exposing set/clear_bdi_lld_congested without explicit comments
that says they should be used only by bottom-level devices
2) A new bdi_state, BDI_lld_congested
3) Use of backing_dev_info for this purpose

If 1), either or both of the followings can be easily done:
[a] Add a comment in backing-dev.h that says set/clear_bdi_lld_congested
should be called only from the bottom device
[b] Move set/clear_bdi_lld_congested from mm/backing-dev.c
to block/blk-core.c, with renaming to blk_set/clear_lld_congested,
so that only a block device that knows what it does will set/clear
the flag

If 2) or 3), I think we need to rewrite the patch in either way of these:
[c] Add a new strategy function to request_queue and use it instead,
e.g. q->lld_busy_fn, which is NULL by default.
Set/clear QUEUE_FLAG_BUSY in request_queue by the bottom device,
and the block layer will check the flag if q->lld_busy_fn is NULL.
[d] Similar to [c], except that storing the busy flag in struct scsi_device
and q->lld_busy_fn() of the scsi device will check that.
If q->lld_busy_fn is NULL, the block layer will just return
'not congested'.

Which do you think is better?

>> BDI_[write|read]_congested flags have been using for queue's
>> congestion, so that I/O queueing/merging can be proceeded even if
>> the lld is congested. So I added a new flag.
>
> iirc, BDI_read/write_congested predated the introduction of the
> congested_fn() and perhaps should have been removed once we went to the
> congested_fn approach. But it's been a while since I spent a lot of
> time looking in there.

Thanks,
--
Jun'ichi Nomura, NEC Corporation


\
 
 \ /
  Last update: 2008-09-22 06:55    [W:0.128 / U:0.348 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site