lkml.org 
[lkml]   [2008]   [Sep]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [Bug #11271] BUG: fealnx in 2.6.27-rc1
Hello all,

On Fri, Sep 12, 2008 at 3:06 PM, Rafael J. Wysocki <rjw@sisk.pl> wrote:

> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=11271
> Subject : BUG: fealnx in 2.6.27-rc1
> Submitter : Jaswinder Singh <jaswinderlinux@gmail.com>
> Date : 2008-08-05 14:58 (39 days old)
> References : http://marc.info/?l=linux-netdev&m=121794762016830&w=4
> http://lkml.org/lkml/2008/8/10/98

I am sorry for delay.

Now I am testing for same problem with 2.6.27-rc6.:
1. On different MYSON Technology Inc SURECOM EP-320X-S 100/10M
Ethernet PCI Adapters
2. On different Linux PCs
3. With different Ethernet switches which supports 100 Mb
4. With different CAT 5 ethernet cables which supports 100 Mb
5. Also checking old patches on fealnx as per Jeff.

And it seems, I am getting following error, with few ethernet switches
and cables and when I switch ethernet cables :
"NETDEV WATCHDOG: eth0 (fealnx): transmit timed out
eth0: Transmit timed out, status 00000000, resetting..."

Now I am trying to confirm that problem is coming from ethernet
switches and cables.

I am also facing one more Issue :

With same 100 Mb ethernet switch and cable my another NIC run at 100
Mb/s and full duplex but MYSON Technology Inc SURECOM EP-320X-S
100/10M runs on 10 Mb/s and half duplex.

I debug fealnx it says : PHYType 1 duplex_mode : 2 line_speed : 2
crvalue : 0xe40e61 bcrvalue : 0x10 imrvalue : 0x46c flags : 0x1

So it is saying duplex_mode : 2 (full duplex) and line_speed = 2
(100M) then why I am getting 10MB half duplex ?

#lspci -vv
02:02.0 Ethernet controller: MYSON Technology Inc SURECOM EP-320X-S
100/10M Ethernet PCI Adapter
Subsystem: MYSON Technology Inc SURECOM EP-320X-S 100/10M
Ethernet PCI Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at ff9ffc00 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at 50000000 [disabled] [size=64K]
Capabilities: [88] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA
PME(D0-,D1+,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: fealnx

#/sbin/ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: Not reported
Advertised auto-negotiation: No
Speed: 10Mb/s
Duplex: Half
Port: MII
PHYAD: 32
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000000 (0)
Link detected: no

Thank you,

Jaswinder Singh.


\
 
 \ /
  Last update: 2008-09-13 10:49    [W:0.409 / U:0.372 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site