lkml.org 
[lkml]   [2008]   [Jul]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] Wait for all codecs to be ready if doing a cold reset
At Tue, 8 Jul 2008 13:59:32 -0300,
Thadeu Lima de Souza Cascardo wrote:
>
> On Tue, Jul 08, 2008 at 12:16:35PM +0200, Takashi Iwai wrote:
> > At Mon, 7 Jul 2008 14:36:55 -0300,
> > Thadeu Lima de Souza Cascardo wrote:
> > >
> > > On Mon, Jul 07, 2008 at 06:39:09PM +0200, Takashi Iwai wrote:
> > > > At Sun, 6 Jul 2008 14:15:56 -0300,
> > > > Thadeu Lima de Souza Cascardo wrote:
> > > > >
> > > > > If AC97_POWER_SAVE is enabled, intel8x0 does a cold reset when
> > > > > initializing the codecs. While resuming, it does not wait for all codecs
> > > > > to be active. Sound card does not work after a resume without it,
> > > > > however. This patch fixes it.
> > > >
> > > > Thanks for the patch.
> > > >
> > > > But, I still don't figure out why this is needed.
> > > > In the else block (with the comment "resume phase"), you can find the
> > > > loop to wait for the all *probed* codecs. The difference with the
> > > > code you moved is that it checks only the bits corresponding to the
> > > > already probed codecs. In other words, the other bits should be
> > > > irrelevant with the hardware.
> > > >
> > > > I guess it's not about the loop but the additional 1/4 sec delay that
> > > > did fix the resume on your device. Please check how is the status
> > > > bits and whether it passed the loop in the middle.
> > > >
> > > >
> > > > Takashi
> > > >
> > > >
> > >
> > > The 1/4 sec delay came in my mind as one of the possible reasons, and
> > > that's why I've made some tests. status and nstatus are 0x200, while
> > > codec_isr_bits is 0x300. The loop waits for the status register give us
> > > 0x300 as the active codecs, instead of the only one probed. Since the
> > > cold reset in the case of a power saving cleans up all codec registers,
> > > it is needed that we wait for all codecs again (like in the probe case).
> >
> > You loaded the modem driver as well?
> > If so, what happens if you unload modem driver?
> >
> >
> > thanks,
> >
> > Takashi
> >
>
> The modem driver has always been loaded. Unloading it with my patch
> works OK.

Well, I meant to unload the modem driver *without* your patch.
That is, does it the unmodified version work if you unload the modem
driver beforehand (e.g. adding it to blacklist)?


thanks,

Takashi

> > > If you need more information or that I ran any more tests, I'd be glad
> > > to do it. By the way, I've tested the patch against your audio and modem
> > > merged version and it works OK.
> > >
> > > Best Regards,
> > > Thadeu Cascardo.
> > >
> > > > > ---
> > > > > sound/pci/intel8x0.c | 24 ++++++++++++++----------
> > > > > 1 files changed, 14 insertions(+), 10 deletions(-)
> > > > >
> > > > > diff --git a/sound/pci/intel8x0.c b/sound/pci/intel8x0.c
> > > > > index 048d99e..7228a0a 100644
> > > > > --- a/sound/pci/intel8x0.c
> > > > > +++ b/sound/pci/intel8x0.c
> > > > > @@ -2335,16 +2335,6 @@ static int snd_intel8x0_ich_chip_init(struct intel8x0 *chip, int probing)
> > > > > igetdword(chip, ICHREG(GLOB_STA)));
> > > > > return -EIO;
> > > > > }
> > > > > -
> > > > > - /* wait for other codecs ready status. */
> > > > > - end_time = jiffies + HZ / 4;
> > > > > - while (status != chip->codec_isr_bits &&
> > > > > - time_after_eq(end_time, jiffies)) {
> > > > > - schedule_timeout_uninterruptible(1);
> > > > > - status |= igetdword(chip, ICHREG(GLOB_STA)) &
> > > > > - chip->codec_isr_bits;
> > > > > - }
> > > > > -
> > > > > } else {
> > > > > /* resume phase */
> > > > > int i;
> > > > > @@ -2363,6 +2353,20 @@ static int snd_intel8x0_ich_chip_init(struct intel8x0 *chip, int probing)
> > > > > } while (time_after_eq(end_time, jiffies));
> > > > > }
> > > > >
> > > > > +#ifndef CONFIG_SND_AC97_POWER_SAVE
> > > > > + if (probing)
> > > > > +#endif
> > > > > + {
> > > > > + /* wait for other codecs ready status. */
> > > > > + end_time = jiffies + HZ / 4;
> > > > > + while (status != chip->codec_isr_bits &&
> > > > > + time_after_eq(end_time, jiffies)) {
> > > > > + schedule_timeout_uninterruptible(1);
> > > > > + status |= igetdword(chip, ICHREG(GLOB_STA)) &
> > > > > + chip->codec_isr_bits;
> > > > > + }
> > > > > + }
> > > > > +
> > > > > if (chip->device_type == DEVICE_SIS) {
> > > > > /* unmute the output on SIS7012 */
> > > > > iputword(chip, 0x4c, igetword(chip, 0x4c) | 1);
> > > > > --
> > > > > 1.5.6
> > > > >


\
 
 \ /
  Last update: 2008-07-08 21:09    [W:0.071 / U:0.096 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site