lkml.org 
[lkml]   [2008]   [Jul]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: 2.6.27-rc7-git1: usb-storage breakage with non-functional disk
On Tue, 8 Jul 2008, Indan Zupancic wrote:

> Any idea why my cardreader doesn't work in the first place though?
>
> The error is basically:
>
> usb 1-5: new high speed USB device using ehci_hcd and address 22
> usb 1-5: device not accepting address 22, error -71
> usb 1-5: new high speed USB device using ehci_hcd and address 23
> usb 1-5: configuration #1 chosen from 1 choice
> scsi17 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 23
> usb-storage: waiting for device to settle before scanning
> usb 1-5: reset high speed USB device using ehci_hcd and address 23
> usb 1-5: reset high speed USB device using ehci_hcd and address 23
> usb 1-5: reset high speed USB device using ehci_hcd and address 23
> scsi 17:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
> usb 1-5: reset high speed USB device using ehci_hcd and address 23
> usb 1-5: device not accepting address 23, error -71
> usb 1-5: reset high speed USB device using ehci_hcd and address 23
> usb 1-5: reset high speed USB device using ehci_hcd and address 23
> usb 1-5: reset high speed USB device using ehci_hcd and address 23
> usb 1-5: reset high speed USB device using ehci_hcd and address 23
> usb 1-5: can't restore configuration #1 (error=-71)
> usb 1-5: USB disconnect, address 23
> sd 17:0:0:0: [sdb] READ CAPACITY failed
> sd 17:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
> sd 17:0:0:0: [sdb] Sense not available.
> sd 17:0:0:0: [sdb] Write Protect is off
> sd 17:0:0:0: [sdb] Mode Sense: 00 00 00 00
> sd 17:0:0:0: [sdb] Assuming drive cache: write through
> sd 17:0:0:0: [sdb] Attached SCSI removable disk
> sd 17:0:0:0: Attached scsi generic sg2 type 0
> usb-storage: device scan complete
> usb 1-5: new high speed USB device using ehci_hcd and address 24
> usb 1-5: string descriptor 0 read error: -71
> usb 1-5: configuration #1 chosen from 1 choice
> usb 1-5: can't set config #1, error -71
>
> It's a new Trust Mini Cardreader, model CR-1350p.

> It doesn't matter in which port I put the thing (front, back),
> and I've tried older kernels too (2.6.12), but I get the same
> error there. This is with an Intel 945G chipset.
> (I've no Windows to test if it works there.)
>
> Is it just a crappy device which I should bring back, or is
> there more going on?

It could be a bad device or it could be a bad USB cable. Have you
tried using the card reader with a different computer?

A usb-storage verbose debugging log might reveal something useful.

Alan Stern



\
 
 \ /
  Last update: 2008-07-08 16:05    [W:0.061 / U:2.520 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site