lkml.org 
[lkml]   [2008]   [Jun]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [linux-pm] [PATCH 0/4] Fix forcedeth hibernate/wake-on-lan problems
On Tue, 3 Jun 2008, Tobias Diedrich wrote:

> One of the ports on the back of the board seems to be broken (Maybe
> esd?), the other three work fine, but nothing happens when I plug a
> device into that one, so I guess that's the culprit.

Sounds like it.

> > The log didn't reveal anything. Perhaps you can learn more by looking
> > at the "registers" file for that OHCI controller in debugfs.
>
> Ok, I can try that this evening...
>
> > Also, you should run "lspci -vv" as root to see what wakeup signals the
> > USB controllers are issuing.

...

> 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) (prog-if 10 [OHCI])
> Subsystem: ASUSTeK Computer Inc. Unknown device 8239
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin A routed to IRQ 23
> Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: ohci_hcd

The OHCI controller settings look normal. It doesn't appear to be
sending a wakeup signal.

> 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) (prog-if 20 [EHCI])
> Subsystem: ASUSTeK Computer Inc. Unknown device 8239
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin B routed to IRQ 20
> Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [44] Debug port: BAR=1 offset=0098
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME+
> Kernel driver in use: ehci_hcd

The EHCI controller settings, however, are strange. The relevant part
is the Power Management Status line near the end:

> Status: D0 PME-Enable- DSel=0 DScale=0 PME+

This means the controller is in the D0 state (as expected) and
PME-Enable is currently turned off ("PME" stands for "Power Management
Event"). But the PME+ at the end means that as soon as PME does get
enabled -- like when the controller is suspended at the start of a
system sleep -- it _will_ send a PME signal.

So for some reason your EHCI controller thinks a wakeup event is
pending. This means you should examine the contents of the "registers"
file in the debugfs directory for the EHCI controller, not OHCI.

Alan Stern



\
 
 \ /
  Last update: 2008-06-03 16:15    [W:1.276 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site