lkml.org 
[lkml]   [2008]   [Jun]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: 2.6.26-rc5-git2: snd-emu10k1 does not work
    At Sun, 29 Jun 2008 19:46:49 +0200,
    Rafael J. Wysocki wrote:
    >
    > On Tuesday, 10 of June 2008, Takashi Iwai wrote:
    > > At Mon, 9 Jun 2008 22:45:01 +0200,
    > > Rafael J. Wysocki wrote:
    > > >
    > > > On Monday, 9 of June 2008, Rafael J. Wysocki wrote:
    > > > > On Monday, 9 of June 2008, Takashi Iwai wrote:
    > > > > > At Sun, 8 Jun 2008 23:03:58 +0200,
    > > > > > Rafael J. Wysocki wrote:
    > > > > > >
    > > > > > > Hi,
    > > > > > >
    > > > > > > snd-emu10k1 doesn't work on one of my test boxes. The driver apparently loads,
    > > > > > > but the card is not visible, for example, to any mixer apps (including the ALSA
    > > > > > > mixer). However, YaST correctly detects and reports the card (the system is
    > > > > > > openSUSE 10.3, x86-64). The openSUSE-made kernel (2.6.22-something) does
    > > > > > > correctly work on the same hardware.
    > > > > > >
    > > > > > > Is there anything I should pay attention to, like any options related to /proc
    > > > > > > or sysfs that could have an effect on the audio adapter?
    > > > > >
    > > > > > First off, check /proc/asound/cards whether snd-emu10k1 driver is
    > > > > > really loaded on the first slot. I guess something else occupies the
    > > > > > position.
    > > > >
    > > > > This is quite possible, as there is an on-board audio in this box too and I'm
    > > > > not sure if the setup switch really turns it off.
    > > > >
    > > > > > If yes, a simple solution is to add the following option for snd module:
    > > > > >
    > > > > > options snd slots=snd-emu10k1
    > > > > >
    > > > > > then the first slot is reserved for emu10k1. Note that this option is
    > > > > > available for 2.6.25 or later kernel.
    > > > >
    > > > > I'll try later today and let you know.
    > > >
    > > > No, it didn't work.
    > > >
    > > > Here's what I got from /proc/asound/cards:
    > > >
    > > > 0 [Audigy ]: Audigy - Audigy 1 [SB0090]
    > > > Audigy 1 [SB0090] (rev.3, serial:0x531102) at 0xa000, irq 17
    > > > 1 [UART ]: MPU-401 UART - MPU-401 UART
    > > > MPU-401 UART at 0x330, irq 10
    > > >
    > > > so I think this is correct, and the "options snd slots=snd-emu10k1" thing had
    > > > no visible effect.
    > >
    > > Then this must be OK. Then the remaining possible problems are:
    > >
    > > - Device files and permissions.
    > > Check whether /dev/snd/* files exist and have proper permissions and
    > > ACL (see "getfacl /dev/snd/*")
    > >
    > > - The default ALSA configuration is hijacked, e.g. via pulse plugin.
    > > Try to remove /etc/asound-pulse.conf if present.
    >
    > I've just installed openSUSE 11.0 on this box and the distro kernel
    > 2.6.25.5-something works, but 2.6.26-rc8 doesn't. The symptoms are exactly
    > the same as described in this thread and the kernel is the only system
    > component replaced.
    >
    > So this is a regression from 2.6.25, actually. Do you want me to bisect?

    Hmm... there is really no visible problematic changes for emu10k1
    between 2.6.25 and 2.6.26. I guess checking /proc/asound/cards and/or
    kernel config would save the time of bisect. At least, check the
    following:

    1. you have emu10k1 in the first entry (#0) of /proc/asound/cards
    2. the mixer states are OK (e.g. "Audigy Analog/Digital Output
    Jack" switch is off, "Master" and "PCM" are muted/adjusted, etc)
    3. run "aplay -Dhw:0 /usr/share/sounds/alsa/test.wav" for testing


    thanks,

    Takashi


    \
     
     \ /
      Last update: 2008-06-30 01:17    [W:0.024 / U:153.684 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site