lkml.org 
[lkml]   [2008]   [Jun]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/6] opti621: use PCI clock value provided by controller
Date
Use PCI clock value provided by controller instead of depending on
a default (or user supplied) value.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.

Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ide/pci/opti621.c | 42 ++++++++++++++++++++++--------------------
1 file changed, 22 insertions(+), 20 deletions(-)

Index: b/drivers/ide/pci/opti621.c
===================================================================
--- a/drivers/ide/pci/opti621.c
+++ b/drivers/ide/pci/opti621.c
@@ -193,11 +193,10 @@ typedef struct pio_clocks_s {
int recovery_time; /* Recovery time (clocks) */
} pio_clocks_t;

-static void compute_clocks(int pio, pio_clocks_t *clks)
+static void compute_clocks(int pio, pio_clocks_t *clks, int bus_speed)
{
if (pio != PIO_NOT_EXIST) {
int adr_setup, data_pls;
- int bus_speed = ide_pci_clk ? ide_pci_clk : system_bus_clock();

adr_setup = ide_pio_timings[pio].setup_time;
data_pls = ide_pio_timings[pio].active_time;
@@ -234,7 +233,7 @@ static void opti621_set_pio_mode(ide_dri
u8 pio1 = 0, pio2 = 0;
pio_clocks_t first, second;
int ax, drdy;
- u8 cycle1, cycle2, misc;
+ u8 cycle1, cycle2, misc, clk;
ide_hwif_t *hwif = HWIF(drive);

/* sets drive->drive_data for both drives */
@@ -242,8 +241,26 @@ static void opti621_set_pio_mode(ide_dri
pio1 = hwif->drives[0].drive_data;
pio2 = hwif->drives[1].drive_data;

- compute_clocks(pio1, &first);
- compute_clocks(pio2, &second);
+ spin_lock_irqsave(&opti621_lock, flags);
+
+ reg_base = hwif->io_ports.data_addr;
+
+ /* allow Register-B */
+ outb(0xc0, reg_base + CNTRL_REG);
+ /* hmm, setupvic.exe does this ;-) */
+ outb(0xff, reg_base + 5);
+ /* if reads 0xff, adapter not exist? */
+ (void)inb(reg_base + CNTRL_REG);
+ /* if reads 0xc0, no interface exist? */
+ read_reg(CNTRL_REG);
+
+ /* check CLK speed */
+ clk = read_reg(STRAP_REG) & 1;
+
+ printk(KERN_INFO "%s: CLK = %d MHz\n", hwif->name, clk ? 25 : 33);
+
+ compute_clocks(pio1, &first, clk ? 25 : 33);
+ compute_clocks(pio2, &second, clk ? 25 : 33);

/* ax = max(a1,a2) */
ax = (first.address_time < second.address_time) ? second.address_time : first.address_time;
@@ -266,21 +283,6 @@ static void opti621_set_pio_mode(ide_dri
second.recovery_time, drdy);
#endif

- spin_lock_irqsave(&opti621_lock, flags);
-
- reg_base = hwif->io_ports.data_addr;
-
- /* allow Register-B */
- outb(0xc0, reg_base + CNTRL_REG);
- /* hmm, setupvic.exe does this ;-) */
- outb(0xff, reg_base + 5);
- /* if reads 0xff, adapter not exist? */
- (void)inb(reg_base + CNTRL_REG);
- /* if reads 0xc0, no interface exist? */
- read_reg(CNTRL_REG);
- /* read version, probably 0 */
- read_reg(STRAP_REG);
-
/* program primary drive */
/* select Index-0 for Register-A */
write_reg(0, MISC_REG);

\
 
 \ /
  Last update: 2008-06-11 22:31    [W:0.042 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site