lkml.org 
[lkml]   [2008]   [May]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: Macbook Pro SATA Drives not seen in 2.6.25
On Tue, 13 May 2008 23:27:21 -0400 AndrewL733 <AndrewL733@aol.com> wrote:

> I have a couple of Macbook Pros. The newest one -- based on the Penryn
> Core 2 Duo with ICH8 -- will not boot with any 2.6.25 kernel (I have
> tried 2.6.25 and 2.6.25.3).

Let's cc linux-ide.

> It boots fine with 2.6.24.7 as well as with
> 2.6.26-rc2. It also boots fine with 2.6.22. I have specific reasons why
> I need to run 2.6.25 so I would appreciate any help here. It seems the
> SATA drives are detected, but then for each partition during bootup I see:
>
> ata3: SATA link down (SStatus 0 SControl 0)
>
> The same 2.6.25 kernels boot fine on my older Macbook Pro with ICH7 and
> I do not see this error.
>
> I would be happy to run a git bisect to help identify the issue, but if
> this problem is already well understood (hey, it's fixed in 2.6.26), I
> can think of better ways to spend my time.

The below went into 2.6.25.1 (or will do so). It looks hopful. Can
you test it please?

> Please copy me personally on any replies. I often subscribe to the list
> but it's too much mail right now. Thanks in advance.

We do that as a matter of course. Or we should...


From: Tejun Heo <htejun@gmail.com>

commit cb6716c879ecf49e2af344926c6a476821812061 upstream

On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write. Verify SIDPR is actually working before enabling it.

This is reported by Ryan Roth in bz#10512.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

---
drivers/ata/ata_piix.c | 25 +++++++++++++++++++++++++
1 file changed, 25 insertions(+)

--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -1531,6 +1531,8 @@ static void __devinit piix_init_sidpr(st
{
struct pci_dev *pdev = to_pci_dev(host->dev);
struct piix_host_priv *hpriv = host->private_data;
+ struct ata_device *dev0 = &host->ports[0]->link.device[0];
+ u32 scontrol;
int i;

/* check for availability */
@@ -1549,6 +1551,29 @@ static void __devinit piix_init_sidpr(st
return;

hpriv->sidpr = pcim_iomap_table(pdev)[PIIX_SIDPR_BAR];
+
+ /* SCR access via SIDPR doesn't work on some configurations.
+ * Give it a test drive by inhibiting power save modes which
+ * we'll do anyway.
+ */
+ scontrol = piix_sidpr_read(dev0, SCR_CONTROL);
+
+ /* if IPM is already 3, SCR access is probably working. Don't
+ * un-inhibit power save modes as BIOS might have inhibited
+ * them for a reason.
+ */
+ if ((scontrol & 0xf00) != 0x300) {
+ scontrol |= 0x300;
+ piix_sidpr_write(dev0, SCR_CONTROL, scontrol);
+ scontrol = piix_sidpr_read(dev0, SCR_CONTROL);
+
+ if ((scontrol & 0xf00) != 0x300) {
+ dev_printk(KERN_INFO, host->dev, "SCR access via "
+ "SIDPR is available but doesn't work\n");
+ return;
+ }
+ }
+
host->ports[0]->ops = &piix_sidpr_sata_ops;
host->ports[1]->ops = &piix_sidpr_sata_ops;
}
--


\
 
 \ /
  Last update: 2008-05-14 10:11    [W:0.859 / U:0.256 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site