lkml.org 
[lkml]   [2008]   [Mar]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: 2.6.25-rc5-mm1
On Thu, 13 Mar 2008 23:05:11 +0100
"Torsten Kaiser" <just.for.lkml@googlemail.com> wrote:

> On Wed, Mar 12, 2008 at 9:01 PM, Torsten Kaiser
> <just.for.lkml@googlemail.com> wrote:
> > On Wed, Mar 12, 2008 at 8:44 PM, Andrew Morton
> > <akpm@linux-foundation.org> wrote:
> > > OK, so it looks like it died during networking initialisation.
> > >
> > > Could you please add initcall_debug to the boot command line so we can see
> > > which function it is getting stuck in?
> >
> > Yes, here is the result:
> > [ 2.573979] PCI-DMA: Disabling AGP.
> > [ 2.577639] PCI-DMA: aperture base @ 8000000 size 65536 KB
> > [ 2.589504] PCI-DMA: using GART IOMMU.
> > [ 2.593258] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
> > [ 2.600132] initcall pci_iommu_init+0x0/0x20() returned 0 after 19 msecs
> > [ 2.622146] calling hpet_late_init+0x0/0x140()
> > [ 2.626689] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
> > [ 2.633022] hpet0: 3 32-bit timers, 25000000 Hz
> > [ 2.638562] initcall hpet_late_init+0x0/0x140() returned 0 after 9 msecs
> > [ 2.654545] calling clocksource_done_booting+0x0/0x20()
> > [ 2.659855] initcall clocksource_done_booting+0x0/0x20()<6>Time:
> >
> > hpet clocksource has been installed.
> > [ 2.662185] returned 0 after 0 msecs
> > [ 2.688448] calling init_pipe_fs+0x0/0x60()
> > [ 2.695423] initcall init_pipe_fs+0x0/0x60() returned 0 after 0 msecs
> > [ 2.705784] calling init_mnt_writers+0x0/0x70()
> > [ 2.711681] initcall init_mnt_writers+0x0/0x70() returned 0 after 0 msecs
> > [ 2.721678] calling eventpoll_init+0x0/0x90()
> > [ 2.731644] initcall eventpoll_init+0x0/0x90() returned 0 after 0 msecs
> > [ 2.738295] calling anon_inode_init+0x0/0x130()
> > [ 2.751614] initcall anon_inode_init+0x0/0x130() returned 0 after 0 msecs
> > [ 2.771585] calling pcie_aspm_init+0x0/0x30()
> > [ 2.779297] initcall pcie_aspm_init+0x0/0x30() returned 0 after 2 msecs
> > [ 2.793911] calling acpi_event_init+0x0/0x52()
> >
> > -> it looked like the system this time already hung here. But just
> > pressing the 'Alt' key let the system continue until the network hang.
> > (I tried this a second time, again it paused here until I pressed a key)
> >
> > [ 94.857929] initcall acpi_event_init+0x0/0x52() returned 0 after 29276 msecs
> > [ 94.865002] calling pnp_system_init+0x0/0x20()
> > [ 94.877935] system 00:06: ioport range 0x4d0-0x4d1 has been reserved
> > [ 94.884286] system 00:06: ioport range 0x7b0-0x7df has been reserved
> > [ 94.897886] system 00:06: ioport range 0x800-0x80f has been reserved
> > [ 94.907886] system 00:06: ioport range 0xbb0-0xbdf has been reserved
> > [ 94.917855] system 00:06: ioport range 0x2000-0x207f has been reserved
> > [ 94.937827] system 00:06: ioport range 0x2080-0x20ff has been reserved
> > [ 94.947827] system 00:06: ioport range 0x2400-0x247f has been reserved
> > [ 94.957793] system 00:06: ioport range 0x2480-0x24ff has been reserved
> > [ 94.977766] system 00:06: ioport range 0x2800-0x287f has been reserved
> > [ 94.987766] system 00:06: ioport range 0x2880-0x28ff has been reserved
> > [ 94.997734] system 00:06: ioport range 0x2c00-0x2c7f has been reserved
> > [ 95.017708] system 00:06: ioport range 0x2c80-0x2cff has been reserved
> > [ 95.024234] system 00:06: iomem range 0x0-0x0 could not be reserved
> > [ 95.037678] system 00:06: iomem range 0xfee01000-0xfeefffff could
> > not be reserved
> > [ 95.060158] system 00:06: iomem range 0xefa80000-0xefabffff has been reserved
> > [ 95.070158] system 00:06: iomem range 0xffb00000-0xffbfffff could
> > not be reserved
> > [ 95.077633] system 00:06: iomem range 0xfff00000-0xffffffff could
> > not be reserved
> > [ 95.097590] system 00:08: iomem range 0xfec00000-0xfec00fff could
> > not be reserved
> > [ 95.120064] system 00:08: iomem range 0xfee00000-0xfee00fff could
> > not be reserved
> > [ 95.130070] system 00:0c: ioport range 0x290-0x297 has been reserved
> > [ 95.137523] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
> > [ 95.157495] system 00:0d: iomem range 0xc0000-0xcffff has been reserved
> > [ 95.167495] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
> > [ 95.177463] system 00:0d: iomem range 0x100000-0xdfffffff could not
> > be reserved
> > [ 95.197437] system 00:0d: iomem range 0xfec00000-0xffffffff could
> > not be reserved
> > [ 95.219983] initcall pnp_system_init+0x0/0x20() returned 0 after 162 msecs
> > [ 95.226887] calling chr_dev_init+0x0/0xd0()
> > [ 95.237813] initcall chr_dev_init+0x0/0xd0() returned 0 after 0 msecs
> > [ 95.247378] calling firmware_class_init+0x0/0x90()
> > [ 95.257320] initcall firmware_class_init+0x0/0x90() returned 0 after 0 msecs
> > [ 95.276031] calling loopback_init+0x0/0x20()
> > [ 95.288590] initcall loopback_init+0x0/0x20() returned 0 after 0 msecs
> > [ 95.296837] calling cpufreq_gov_performance_init+0x0/0x20()
> > [ 95.309084] initcall cpufreq_gov_performance_init+0x0/0x20()
> > returned 0 after 0 msecs
> > [ 95.317734] calling cpufreq_gov_dbs_init+0x0/0x50()
> > [ 95.338090] initcall cpufreq_gov_dbs_init+0x0/0x50() returned 0 after 0 msecs
> > [ 95.345254] calling init_acpi_pm_clocksource+0x0/0xc0()
> > [ 95.355293] initcall init_acpi_pm_clocksource+0x0/0xc0() returned 0
> > after 0 msecs
> > [ 95.374115] calling pcibios_assign_resources+0x0/0x90()
> > [ 95.379618] PCI: Bridge: 0000:00:06.0
> > [ 95.394087] IO window: disabled.
> > [ 95.397502] MEM window: 0xeff00000-0xefffffff
> > [ 95.402032] PREFETCH window: 0x00000000eef00000-0x00000000eeffffff
> > [ 95.415189] PCI: Bridge: 0000:00:0b.0
> > [ 95.418860] IO window: e000-efff
> > [ 95.438075] MEM window: 0xefe00000-0xefefffff
> > [ 95.442610] PREFETCH window: disabled.
> > [ 95.455526] PCI: Bridge: 0000:00:0c.0
> > [ 95.459197] IO window: disabled.
> > [ 95.462604] MEM window: 0xefd00000-0xefdfffff
> > [ 95.475513] PREFETCH window: disabled.
> > [ 95.479443] PCI: Bridge: 0000:00:0d.0
> > [ 95.485512] IO window: disabled.
> > [ 95.495480] MEM window: 0xefc00000-0xefcfffff
> > [ 95.500010] PREFETCH window: disabled.
> > [ 95.515455] PCI: Bridge: 0000:00:0f.0
> > [ 95.519124] IO window: d000-dfff
> > [ 95.522533] MEM window: 0xefb00000-0xefbfffff
> > [ 95.535423] PREFETCH window: 0x00000000e0000000-0x00000000e7ffffff
> > [ 95.545456] initcall pcibios_assign_resources+0x0/0x90() returned 0
> > after 79 msecs
> > [ 95.557830] calling fill_mp_bus_to_cpumask+0x0/0x100()
> > [ 95.575408] initcall fill_mp_bus_to_cpumask+0x0/0x100() returned 0
> > after 0 msecs
> > [ 95.593777] calling inet_init+0x0/0x380()
> > [ 95.597890] NET: Registered protocol family 2
> >
> > -> same hang, no reaction to SysRq.
> >
> > What looks suspicious: The call to pcie_aspm_init is just before the
> > temporary hang. When I used make oldconfig to upgrade the .config from
> > 2.6.25-rc3-mm1 to -rc5-mm1 I activated the new option CONFIG_PCIEASPM.
> >
> > I will try with CONFIG_PCIEASPM_DEBUG added and completely without this option.
>
> CONFIG_PCIEASPM does not change anything.
> Also testing the range of ipc patches you suggested to Badari did not fix it.
>
> I did a bisect, these patches are currently remaining, but I dod not
> have the time for more bisect steps until tomorrow:

OK, thanks for persisting.

> git-scsi-misc
> git-sh
> execute-tasklets-in-the-same-order-they-were-queued
> git-sched
> sched: work around hrtick related lockup
> sched: make sure jiffies is up to date before calling __update_rq_clock()
> sched: fix rq->clock overflows detection with CONFIG_NO_HZ
> sched: make cpu_clock() globally synchronous
> sched: remove isolcpus
> ftrace: make the task state char-string visible to all
> sched: add latency tracer callbacks to the scheduler

the sched patches, perhaps..

> latencytop: optimize LT_BACKTRACEDEPTH loops a bit
> sched: cleanup old and rarely used 'debug' features.
> [SCSI] zfcp: convert zfcp to use target reset and device reset handler
> [SCSI] qla4xxx: Add target reset functionality
> [SCSI] scsi_error: add target reset handler
> [SCSI] ps3rom: Simplify fill_from_dev_buffer()
> [SCSI] scsi_debug: use shost_priv macro
> [SCSI] scsi_debug: remove unnecessary checking
> [SCSI] scsi_debug: remove scsi_debug.h
> [SCSI] scsi_debug: stop including drivers/scsi/scsi.h
> [SCSI] Remove random noop unchecked_isa_dma users
> [SCSI] aacraid: READ_CAPACITY_16 shouldn't trust allocation length in cdb
> [SCSI] st: show options currently set in sysfs
> [SCSI] st: add option to use SILI in variable block reads
> [SCSI] gdth: remove command accessors
> [SCSI] aic94xx: Use sas_request_addr() to provide SAS WWN if the
> adapter lacks one
> [SCSI] libsas: Provide a transport-level facility to request SAS addrs
> [SCSI] ips: sg chaining support to the path to non I/O commands
> [SCSI] gdth: convert to PCI hotplug API
> [SCSI] gdth: PCI probe cleanups, prep for PCI hotplug API conversion
> rtc: rtc-sh: Add support for periodic IRQs.
> sh: SuperH KEYSC keypad data for Solution Engine 7722
> sh: SuperH KEYSC keypad data for MigoR
> sh: SuperH KEYSC platform driver
>



\
 
 \ /
  Last update: 2008-03-13 23:39    [W:0.199 / U:1.404 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site