lkml.org 
[lkml]   [2008]   [Dec]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    SubjectOops in 2.6.28-rc9 and -rc8 -- mtrr issues / e1000e
    Date
    Please forgive my posting “newness”.  If there’s anything I’m missing,
    please let me know.

    I’ve got a brand new machine that I’m having a terrible time trying to keep
    up and running with any “newer” kernels.   I have about 8 of these servers
    that don’t have an issue, but they’re running older kernels and or don’t
    have the load of this machine.

    As of right now, I’m running Centos 5.2 x86-64 on a Tyan 5397 MB with (2)
    Quad Core Intel CPUs, 32GB of ram (16 2GB sticks, ECC FBDIMMS), and a large
    24 drive raid on an Adaptec AACRAID card.   Right now, I’ve got the board
    back on bios v1.03.  I’ve tried 1.04 and 1.04beta.   Since my other systems
    don’t have this issue, I thought it was a bad MB.  It was not.  Problems
    persist on both new boards.    X86-64 gets me much longer “uptimes” than
    32bit RHEL 5.2.   The e1000e’s enabled causes the box to crash much, much
    sooner.  I have a feeling their reserved memory is getting stomped on,
    causing the grief.   Memory tests clean, and there are no ECC events listed
    in bios.  Bios 1.04beta did show correct memory sizing in dmidecode, as its
    fix on Tyan’s website says DMI Table update.

    By bypassing the onboard nics (e1000e) and using some older pci-x Intel
    e1000 cards, I can get the box to stay up for around 11 hours.   Sometimes
    5, and sometimes 14 hours.  If I use the onboard e1000e nics, I’ll get a
    tx_unit_hang error within hours.   The server is doing about 300-400 mbits
    of webserving.   Server loads are around 0.4-1.0.

    I hope this is as simple as me doing something glaringly wrong in the kernel
    config, and missing something vital.   Btw, I get the same crashes in
    2.6.27.6 and 2.6.27.9 as well.   One of the other servers like this one,
    doesn’t have any issues with 2.6.27.6, RHEL 5.2 32bit. 

    Thanks!

    Doug Bazarnic

    Uname:
    Linux mem3 2.6.28-rc9 #9 SMP Sat Dec 20 18:56:23 MST 2008 x86_64 x86_64
    x86_64 GNU/Linux

    This spits up at the terminal, and box will go down within minutes:
    root@mem3 etc]#
    Message from syslogd@ at Mon Dec 22 00:40:57 2008 ...
    mem3 kernel: Bad page state in process 'kswapd0'
    Message from syslogd@ at Mon Dec 22 00:40:57 2008 ...
    mem3 kernel: page:ffffe20010b36b88 flags:0x80001a0000010008
    mapping:0000000000000000 mapcount:-721420288 count:0
    Message from syslogd@ at Mon Dec 22 00:40:57 2008 ...
    mem3 kernel: Trying to fix it up, but a reboot is needed
    Message from syslogd@ at Mon Dec 22 00:40:57 2008 ...
    mem3 kernel: Backtrace:

    dmesg of the crash shows:  (Box must be hard rebooted to come back up –
    reboot or ctrl-alt-del does nothing)
    Bad page state in process 'kswapd0'
    page:ffffe20010b36b88 flags:0x80001a0000010008 mapping:0000000000000000
    mapcount:-721420288 count:0
    Trying to fix it up, but a reboot is needed
    Backtrace:
    Pid: 377, comm: kswapd0 Tainted: G        W  2.6.28-rc9 #9
    Call Trace:
     [<ffffffff80263bc2>] bad_page+0x6b/0x96
     [<ffffffff80264562>] free_hot_cold_page+0xa0/0x192
     [<ffffffff80264675>] __pagevec_free+0x21/0x2e
     [<ffffffff80269281>] shrink_page_list+0x51a/0x608
     [<ffffffff802695b0>] shrink_list+0x241/0x501
     [<ffffffff8024189b>] bit_waitqueue+0x10/0x8e
     [<ffffffff80265cb9>] determine_dirtyable_memory+0xd/0x20
     [<ffffffff8022acbb>] enqueue_task_fair+0xd6/0xea
     [<ffffffff80269ad4>] shrink_zone+0x264/0x2e8
     [<ffffffff8026a3e2>] kswapd+0x383/0x4c3
     [<ffffffff8026823d>] isolate_pages_global+0x0/0x21d
     [<ffffffff8051b979>] thread_return+0x3d/0xa2
     [<ffffffff80241968>] autoremove_wake_function+0x0/0x2e
     [<ffffffff8026a05f>] kswapd+0x0/0x4c3
     [<ffffffff8024184c>] kthread+0x47/0x73
     [<ffffffff8022ceb8>] schedule_tail+0x28/0x60
     [<ffffffff8020c029>] child_rip+0xa/0x11
     [<ffffffff80241805>] kthread+0x0/0x73
     [<ffffffff8020c01f>] child_rip+0x0/0x11

    Full dmesg on rebooted box:  (note the mtrr warnings)

    BIOS EBDA/lowmem at: 0009a000/0009a000
    Linux version 2.6.28-rc9 (root@localhost.localdomain) (gcc version 4.1.2
    20071124 (Red Hat 4.1.2-42)) #9 SMP Sat Dec 20 18:56:23 MST 2008
    Command line: ro root=LABEL=/
    KERNEL supported cpus:
      Intel GenuineIntel
      AMD AuthenticAMD
      Centaur CentaurHauls
    BIOS-provided physical RAM map:
     BIOS-e820: 0000000000000000 - 000000000009a000 (usable)
     BIOS-e820: 000000000009a000 - 00000000000a0000 (reserved)
     BIOS-e820: 00000000000c8000 - 00000000000d4000 (reserved)
     BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
     BIOS-e820: 0000000000100000 - 00000000bff50000 (usable)
     BIOS-e820: 00000000bff50000 - 00000000bff5f000 (ACPI data)
     BIOS-e820: 00000000bff5f000 - 00000000bff60000 (ACPI NVS)
     BIOS-e820: 00000000bff60000 - 00000000c0000000 (reserved)
     BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
     BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
     BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
     BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
     BIOS-e820: 0000000100000000 - 0000000840000000 (usable)
    DMI present.
    Phoenix BIOS detected: BIOS may corrupt low RAM, working it around.
    last_pfn = 0x840000 max_arch_pfn = 0x3ffffffff
    x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    ------------[ cut here ]------------
    WARNING: at arch/x86/kernel/cpu/mtrr/generic.c:404
    generic_get_mtrr+0xbc/0xf5()
    mtrr: your BIOS has set up an incorrect mask, fixing it up.
    Modules linked in:
    Pid: 0, comm: swapper Not tainted 2.6.28-rc9 #9
    Call Trace:
     [<ffffffff80230b9c>] warn_slowpath+0xf3/0x111
     [<ffffffff80231828>] printk+0x8d/0x95
     [<ffffffff8021672b>] post_set+0x20/0x3d
     [<ffffffff80231828>] printk+0x8d/0x95
     [<ffffffff80216c07>] generic_get_mtrr+0xbc/0xf5
     [<ffffffff806e0d69>] mtrr_trim_uncached_memory+0x7b/0x2fe
     [<ffffffff806e85a2>] early_gart_iommu_check+0x9e/0x268
     [<ffffffff806dd01c>] setup_arch+0x3e9/0x619
     [<ffffffff806d6959>] start_kernel+0x6f/0x325
     [<ffffffff806d638e>] x86_64_start_kernel+0xde/0xe2
    ---[ end trace 4eaa2a86a8e2da22 ]---
    last_pfn = 0xbff50 max_arch_pfn = 0x3ffffffff
    init_memory_mapping: 0000000000000000-00000000bff50000
     0000000000 - 00bfe00000 page 2M
     00bfe00000 - 00bff50000 page 4k
    kernel direct mapping tables up to bff50000 @ 10000-15000
    last_map_addr: bff50000 end: bff50000
    init_memory_mapping: 0000000100000000-0000000840000000
     0100000000 - 0840000000 page 2M
    kernel direct mapping tables up to 840000000 @ 13000-35000
    last_map_addr: 840000000 end: 840000000
    RAMDISK: 37dd3000 - 37fefa9c
    ACPI: RSDP 000F7060, 0024 (r2 PTLTD )
    ACPI: XSDT BFF58E2F, 009C (r1 PTLTD      XSDT    6040000  LTP        0)
    ACPI: FACP BFF5ED60, 00F4 (r3 INTEL  TUMWATER  6040000 PTL         3)
    ACPI: DSDT BFF5A9B9, 4333 (r1  Intel SEABURG   6040000 MSFT  3000000)
    ACPI: FACS BFF5FFC0, 0040
    ACPI: _MAR BFF5EE54, 0030 (r1 Intel  OEMDMAR   6040000 LOHR        1)
    ACPI: APIC BFF5EE84, 00C8 (r1 PTLTD      APIC    6040000  LTP        0)
    ACPI: MCFG BFF5EF4C, 003C (r1 PTLTD    MCFG    6040000  LTP        0)
    ACPI: BOOT BFF5EF88, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
    ACPI: SPCR BFF5EFB0, 0050 (r1 PTLTD  $UCRTBL$  6040000 PTL         1)
    ACPI: SSDT BFF5A75A, 025F (r1  PmRef  Cpu0Tst     3000 INTL 20050228)
    ACPI: SSDT BFF5A6B4, 00A6 (r1  PmRef  Cpu7Tst     3000 INTL 20050228)
    ACPI: SSDT BFF5A60E, 00A6 (r1  PmRef  Cpu6Tst     3000 INTL 20050228)
    ACPI: SSDT BFF5A568, 00A6 (r1  PmRef  Cpu5Tst     3000 INTL 20050228)
    ACPI: SSDT BFF5A4C2, 00A6 (r1  PmRef  Cpu4Tst     3000 INTL 20050228)
    ACPI: SSDT BFF5A41C, 00A6 (r1  PmRef  Cpu3Tst     3000 INTL 20050228)
    ACPI: SSDT BFF5A376, 00A6 (r1  PmRef  Cpu2Tst     3000 INTL 20050228)
    ACPI: SSDT BFF5A2D0, 00A6 (r1  PmRef  Cpu1Tst     3000 INTL 20050228)
    ACPI: SSDT BFF58ECB, 1405 (r1  PmRef    CpuPm     3000 INTL 20050228)
    ACPI: Local APIC address 0xfee00000
    (7 early reservations) ==> bootmem [0000000000 - 0840000000]
      #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 -
    0000001000]
      #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 -
    0000008000]
      #2 [0000200000 - 00007e0f54]    TEXT DATA BSS ==> [0000200000 -
    00007e0f54]
      #3 [0037dd3000 - 0037fefa9c]          RAMDISK ==> [0037dd3000 -
    0037fefa9c]
      #4 [000009a000 - 0000100000]    BIOS reserved ==> [000009a000 -
    0000100000]
      #5 [0000010000 - 0000013000]          PGTABLE ==> [0000010000 -
    0000013000]
      #6 [0000013000 - 0000030000]          PGTABLE ==> [0000013000 -
    0000030000]
     [ffffe20000000000-ffffe2000f9fffff] PMD ->
    [ffff880028200000-ffff880037bfffff] on node 0
     [ffffe2000fa00000-ffffe2001cdfffff] PMD ->
    [ffff880038000000-ffff8800453fffff] on node 0
    Zone PFN ranges:
      DMA      0x00000010 -> 0x00001000
      DMA32    0x00001000 -> 0x00100000
      Normal   0x00100000 -> 0x00840000
    Movable zone start PFN for each node
    early_node_map[3] active PFN ranges
        0: 0x00000010 -> 0x0000009a
        0: 0x00000100 -> 0x000bff50
        0: 0x00100000 -> 0x00840000
    On node 0 totalpages: 8388314
      DMA zone: 56 pages used for memmap
      DMA zone: 1641 pages reserved
      DMA zone: 2281 pages, LIFO batch:0
      DMA32 zone: 14280 pages used for memmap
      DMA32 zone: 767880 pages, LIFO batch:31
      Normal zone: 103936 pages used for memmap
      Normal zone: 7498240 pages, LIFO batch:31
      Movable zone: 0 pages used for memmap
    ACPI: PM-Timer IO Port: 0x1008
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled)
    ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled)
    ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled)
    ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled)
    ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
    ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23
    ACPI: IOAPIC (id[0x09] address[0xfec88000] gsi_base[24])
    IOAPIC[1]: apic_id 9, version 0, address 0xfec88000, GSI 24-47
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    SMP: Allowing 8 CPUs, 0 hotplug CPUs
    Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
    PERCPU: Allocating 45056 bytes of per cpu data
    NR_CPUS: 16, nr_cpu_ids: 8, nr_node_ids 1
    Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8268401
    Kernel command line: ro root=LABEL=/
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 32768 bytes)
    Extended CMOS year: 2000
    TSC: PIT calibration matches PMTIMER. 1 loops
    Detected 2659.992 MHz processor.
    Console: colour VGA+ 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes)
    Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes)
    Checking aperture...
    No AGP bridge found
    PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    Placing software IO TLB between 0x20000000 - 0x24000000
    Memory: 32954916k/34603008k available (3212k kernel code, 1049752k absent,
    597392k reserved, 1537k data, 388k init)
    Calibrating delay loop (skipped), value calculated using timer frequency..
    5319.98 BogoMIPS (lpj=2659992)
    Mount-cache hash table entries: 256
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 6144K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 0
    CPU0: Thermal monitoring enabled (TM2)
    using mwait in idle threads.
    Freeing SMP alternatives: 29k freed
    ACPI: Core revision 20080926
    Setting APIC routing to flat
    ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    CPU0: Intel(R) Xeon(R) CPU           E5430  @ 2.66GHz stepping 06
    Booting processor 1 APIC 0x4 ip 0x6000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 5319.27 BogoMIPS
    (lpj=2659639)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 6144K
    CPU: Physical Processor ID: 1
    CPU: Processor Core ID: 0
    CPU1: Thermal monitoring enabled (TM2)
    x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
    CPU1: Intel(R) Xeon(R) CPU           E5430  @ 2.66GHz stepping 06
    checking TSC synchronization [CPU#0 -> CPU#1]: passed.
    Booting processor 2 APIC 0x1 ip 0x6000
    Initializing CPU#2
    Calibrating delay using timer specific routine.. 5319.23 BogoMIPS
    (lpj=2659618)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 6144K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU2: Thermal monitoring enabled (TM2)
    x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106
    CPU2: Intel(R) Xeon(R) CPU           E5430  @ 2.66GHz stepping 06
    checking TSC synchronization [CPU#0 -> CPU#2]: passed.
    Booting processor 3 APIC 0x5 ip 0x6000
    Initializing CPU#3
    Calibrating delay using timer specific routine.. 5319.26 BogoMIPS
    (lpj=2659634)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 6144K
    CPU: Physical Processor ID: 1
    CPU: Processor Core ID: 1
    CPU3: Thermal monitoring enabled (TM2)
    x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
    CPU3: Intel(R) Xeon(R) CPU           E5430  @ 2.66GHz stepping 06
    checking TSC synchronization [CPU#0 -> CPU#3]: passed.
    Booting processor 4 APIC 0x2 ip 0x6000
    Initializing CPU#4
    Calibrating delay using timer specific routine.. 5319.24 BogoMIPS
    (lpj=2659621)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 6144K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 2
    CPU4: Thermal monitoring enabled (TM2)
    x86 PAT enabled: cpu 4, old 0x7040600070406, new 0x7010600070106
    CPU4: Intel(R) Xeon(R) CPU           E5430  @ 2.66GHz stepping 06
    checking TSC synchronization [CPU#0 -> CPU#4]: passed.
    Booting processor 5 APIC 0x6 ip 0x6000
    Initializing CPU#5
    Calibrating delay using timer specific routine.. 5319.25 BogoMIPS
    (lpj=2659627)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 6144K
    CPU: Physical Processor ID: 1
    CPU: Processor Core ID: 2
    CPU5: Thermal monitoring enabled (TM2)
    x86 PAT enabled: cpu 5, old 0x7040600070406, new 0x7010600070106
    CPU5: Intel(R) Xeon(R) CPU           E5430  @ 2.66GHz stepping 06
    checking TSC synchronization [CPU#0 -> CPU#5]: passed.
    Booting processor 6 APIC 0x3 ip 0x6000
    Initializing CPU#6
    Calibrating delay using timer specific routine.. 5319.22 BogoMIPS
    (lpj=2659612)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 6144K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 3
    CPU6: Thermal monitoring enabled (TM2)
    x86 PAT enabled: cpu 6, old 0x7040600070406, new 0x7010600070106
    CPU6: Intel(R) Xeon(R) CPU           E5430  @ 2.66GHz stepping 06
    checking TSC synchronization [CPU#0 -> CPU#6]: passed.
    Booting processor 7 APIC 0x7 ip 0x6000
    Initializing CPU#7
    Calibrating delay using timer specific routine.. 5319.26 BogoMIPS
    (lpj=2659633)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 6144K
    CPU: Physical Processor ID: 1
    CPU: Processor Core ID: 3
    CPU7: Thermal monitoring enabled (TM2)
    x86 PAT enabled: cpu 7, old 0x7040600070406, new 0x7010600070106
    CPU7: Intel(R) Xeon(R) CPU           E5430  @ 2.66GHz stepping 06
    checking TSC synchronization [CPU#0 -> CPU#7]: passed.
    Brought up 8 CPUs
    Total of 8 processors activated (42554.75 BogoMIPS).
    net_namespace: 552 bytes
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 31
    PCI: MCFG area at e0000000 reserved in E820
    PCI: Using MMCONFIG at e0000000 - e1ffffff
    PCI: Using configuration type 1 for base access
    ACPI: EC: Look up EC in DSDT
    ACPI: Interpreter enabled
    ACPI: (supports S0 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: No dock devices found.
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:00.0: PME# disabled
    pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:01.0: PME# disabled
    pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:05.0: PME# disabled
    pci 0000:00:09.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:09.0: PME# disabled
    pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.0: PME# disabled
    pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f]
    pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f]
    pci 0000:00:1d.2: reg 20 io port: [0x1840-0x185f]
    pci 0000:00:1d.3: reg 20 io port: [0x1860-0x187f]
    pci 0000:00:1d.7: reg 10 32bit mmio: [0xdc704000-0xdc7043ff]
    pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    pci 0000:00:1d.7: PME# disabled
    pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
    pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
    pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
    pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
    pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
    pci 0000:00:1f.1: reg 20 io port: [0x1880-0x188f]
    pci 0000:00:1f.2: reg 10 io port: [0x18d0-0x18d7]
    pci 0000:00:1f.2: reg 14 io port: [0x18c8-0x18cb]
    pci 0000:00:1f.2: reg 18 io port: [0x18c0-0x18c7]
    pci 0000:00:1f.2: reg 1c io port: [0x1894-0x1897]
    pci 0000:00:1f.2: reg 20 io port: [0x18a0-0x18bf]
    pci 0000:00:1f.2: reg 24 32bit mmio: [0xdc704400-0xdc7047ff]
    pci 0000:00:1f.2: PME# supported from D3hot
    pci 0000:00:1f.2: PME# disabled
    pci 0000:00:1f.3: reg 20 io port: [0x18e0-0x18ff]
    pci 0000:01:00.0: reg 10 64bit mmio: [0xdc000000-0xdc1fffff]
    pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x07ffff]
    pci 0000:01:00.0: supports D1
    pci 0000:00:01.0: bridge 32bit mmio: [0xdc000000-0xdc1fffff]
    pci 0000:09:00.0: PME# supported from D0 D3hot D3cold
    pci 0000:09:00.0: PME# disabled
    pci 0000:09:00.3: PME# supported from D0 D3hot D3cold
    pci 0000:09:00.3: PME# disabled
    pci 0000:00:09.0: bridge io port: [0x2000-0x2fff]
    pci 0000:00:09.0: bridge 32bit mmio: [0xdc200000-0xdc3fffff]
    pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold
    pci 0000:0a:00.0: PME# disabled
    pci 0000:0a:02.0: PME# supported from D0 D3hot D3cold
    pci 0000:0a:02.0: PME# disabled
    pci 0000:10:09.0: reg 10 64bit mmio: [0xdc280000-0xdc29ffff]
    pci 0000:10:09.0: reg 18 64bit mmio: [0xdc200000-0xdc23ffff]
    pci 0000:10:09.0: reg 20 io port: [0x2000-0x203f]
    pci 0000:10:09.0: reg 30 32bit mmio: [0x000000-0x03ffff]
    pci 0000:10:0a.0: reg 10 64bit mmio: [0xdc2a0000-0xdc2bffff]
    pci 0000:10:0a.0: reg 18 64bit mmio: [0xdc240000-0xdc27ffff]
    pci 0000:10:0a.0: reg 20 io port: [0x2040-0x207f]
    pci 0000:10:0a.0: reg 30 32bit mmio: [0x000000-0x03ffff]
    pci 0000:10:0a.0: PME# supported from D0 D3hot D3cold
    pci 0000:10:0a.0: PME# disabled
    pci 0000:09:00.3: bridge io port: [0x2000-0x2fff]
    pci 0000:09:00.3: bridge 32bit mmio: [0xdc200000-0xdc2fffff]
    pci 0000:20:05.0: reg 10 32bit mmio: [0xd8000000-0xdbffffff]
    pci 0000:20:05.0: reg 14 32bit mmio: [0xdc400000-0xdc43ffff]
    pci 0000:20:05.0: reg 18 io port: [0x3000-0x307f]
    pci 0000:20:05.0: supports D1 D2
    pci 0000:00:1e.0: transparent bridge
    pci 0000:00:1e.0: bridge io port: [0x3000-0x3fff]
    pci 0000:00:1e.0: bridge 32bit mmio: [0xdc400000-0xdc4fffff]
    pci 0000:00:1e.0: bridge 64bit mmio pref: [0xd8000000-0xdbffffff]
    bus 00 -> node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9.BMD0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9.BMD0.BPD0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9.BMD0.BPD2._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9.BMF3._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 14 15) *9
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 14 15) *12
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 14 15)
    ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 *11 14 15)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 10 11 14 15)
    ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 *10 11 14 15)
    SCSI subsystem initialized
    libata version 3.00 loaded.
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    dca service started, version 1.4
    PCI: Using ACPI for IRQ routing
    PCI-GART: No AMD GART found.
    hpet clockevent registered
    HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 11 devices
    ACPI: ACPI bus type pnp unregistered
    system 00:01: ioport range 0x4d0-0x4d1 has been reserved
    system 00:01: ioport range 0x800-0x80f has been reserved
    system 00:01: ioport range 0x1000-0x107f has been reserved
    system 00:01: ioport range 0x1180-0x11bf has been reserved
    system 00:01: ioport range 0xfe00-0xfe00 has been reserved
    system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
    system 00:01: iomem range 0xfee00000-0xfee0ffff could not be reserved
    system 00:01: iomem range 0xfec00000-0xfec00fff has been reserved
    system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
    system 00:01: iomem range 0xfec88000-0xfec88fff has been reserved
    system 00:01: iomem range 0xfe000000-0xfe01ffff has been reserved
    system 00:01: iomem range 0xfe600000-0xfe6fffff has been reserved
    pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
    pci 0000:00:01.0:   IO window: disabled
    pci 0000:00:01.0:   MEM window: 0xdc000000-0xdc1fffff
    pci 0000:00:01.0:   PREFETCH window: 0x000000c2000000-0x000000c20fffff
    pci 0000:00:05.0: PCI bridge, secondary bus 0000:05
    pci 0000:00:05.0:   IO window: disabled
    pci 0000:00:05.0:   MEM window: disabled
    pci 0000:00:05.0:   PREFETCH window: disabled
    pci 0000:0a:00.0: PCI bridge, secondary bus 0000:0b
    pci 0000:0a:00.0:   IO window: disabled
    pci 0000:0a:00.0:   MEM window: disabled
    pci 0000:0a:00.0:   PREFETCH window: disabled
    pci 0000:0a:02.0: PCI bridge, secondary bus 0000:0f
    pci 0000:0a:02.0:   IO window: disabled
    pci 0000:0a:02.0:   MEM window: disabled
    pci 0000:0a:02.0:   PREFETCH window: disabled
    pci 0000:09:00.0: PCI bridge, secondary bus 0000:0a
    pci 0000:09:00.0:   IO window: disabled
    pci 0000:09:00.0:   MEM window: disabled
    pci 0000:09:00.0:   PREFETCH window: disabled
    pci 0000:09:00.3: PCI bridge, secondary bus 0000:10
    pci 0000:09:00.3:   IO window: 0x2000-0x2fff
    pci 0000:09:00.3:   MEM window: 0xdc200000-0xdc2fffff
    pci 0000:09:00.3:   PREFETCH window: 0x000000c2100000-0x000000c21fffff
    pci 0000:00:09.0: PCI bridge, secondary bus 0000:09
    pci 0000:00:09.0:   IO window: 0x2000-0x2fff
    pci 0000:00:09.0:   MEM window: 0xdc200000-0xdc3fffff
    pci 0000:00:09.0:   PREFETCH window: 0x000000c2100000-0x000000c21fffff
    pci 0000:00:1c.0: PCI bridge, secondary bus 0000:1f
    pci 0000:00:1c.0:   IO window: disabled
    pci 0000:00:1c.0:   MEM window: disabled
    pci 0000:00:1c.0:   PREFETCH window: disabled
    pci 0000:00:1e.0: PCI bridge, secondary bus 0000:20
    pci 0000:00:1e.0:   IO window: 0x3000-0x3fff
    pci 0000:00:1e.0:   MEM window: 0xdc400000-0xdc4fffff
    pci 0000:00:1e.0:   PREFETCH window: 0x000000d8000000-0x000000dbffffff
    pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:01.0: setting latency timer to 64
    pci 0000:00:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:05.0: setting latency timer to 64
    pci 0000:00:09.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:09.0: setting latency timer to 64
    pci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci 0000:09:00.0: setting latency timer to 64
    pci 0000:0a:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci 0000:0a:00.0: setting latency timer to 64
    pci 0000:0a:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    pci 0000:0a:02.0: setting latency timer to 64
    pci 0000:09:00.3: setting latency timer to 64
    pci 0000:00:1c.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
    pci 0000:00:1c.0: setting latency timer to 64
    pci 0000:00:1e.0: setting latency timer to 64
    bus: 00 index 0 io port: [0x00-0xffff]
    bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff]
    bus: 01 index 0 mmio: [0x0-0x0]
    bus: 01 index 1 mmio: [0xdc000000-0xdc1fffff]
    bus: 01 index 2 mmio: [0xc2000000-0xc20fffff]
    bus: 01 index 3 mmio: [0x0-0x0]
    bus: 05 index 0 mmio: [0x0-0x0]
    bus: 05 index 1 mmio: [0x0-0x0]
    bus: 05 index 2 mmio: [0x0-0x0]
    bus: 05 index 3 mmio: [0x0-0x0]
    bus: 09 index 0 io port: [0x2000-0x2fff]
    bus: 09 index 1 mmio: [0xdc200000-0xdc3fffff]
    bus: 09 index 2 mmio: [0xc2100000-0xc21fffff]
    bus: 09 index 3 mmio: [0x0-0x0]
    bus: 0a index 0 mmio: [0x0-0x0]
    bus: 0a index 1 mmio: [0x0-0x0]
    bus: 0a index 2 mmio: [0x0-0x0]
    bus: 0a index 3 mmio: [0x0-0x0]
    bus: 0b index 0 mmio: [0x0-0x0]
    bus: 0b index 1 mmio: [0x0-0x0]
    bus: 0b index 2 mmio: [0x0-0x0]
    bus: 0b index 3 mmio: [0x0-0x0]
    bus: 0f index 0 mmio: [0x0-0x0]
    bus: 0f index 1 mmio: [0x0-0x0]
    bus: 0f index 2 mmio: [0x0-0x0]
    bus: 0f index 3 mmio: [0x0-0x0]
    bus: 10 index 0 io port: [0x2000-0x2fff]
    bus: 10 index 1 mmio: [0xdc200000-0xdc2fffff]
    bus: 10 index 2 mmio: [0xc2100000-0xc21fffff]
    bus: 10 index 3 mmio: [0x0-0x0]
    bus: 1f index 0 mmio: [0x0-0x0]
    bus: 1f index 1 mmio: [0x0-0x0]
    bus: 1f index 2 mmio: [0x0-0x0]
    bus: 1f index 3 mmio: [0x0-0x0]
    bus: 20 index 0 io port: [0x3000-0x3fff]
    bus: 20 index 1 mmio: [0xdc400000-0xdc4fffff]
    bus: 20 index 2 mmio: [0xd8000000-0xdbffffff]
    bus: 20 index 3 io port: [0x00-0xffff]
    bus: 20 index 4 mmio: [0x000000-0xffffffffffffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
    TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
    TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    TCP: Hash tables configured (established 262144 bind 65536)
    TCP reno registered
    NET: Registered protocol family 1
    checking if image is initramfs... it is
    Freeing initrd memory: 2162k freed
    Simple Boot Flag at 0x40 set to 0x80
    Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
    alg: cipher: Test 1 failed on encryption for aes-asm
    00000000: 00 01 02 03 04 05 06 07 08 08 08 08 08 08 08 08
    audit: initializing netlink socket (disabled)
    type=2000 audit(1229934097.774:1): initialized
    HugeTLB registered 2 MB page size, pre-allocated 0 pages
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    SGI XFS with security attributes, large block/inode numbers, no debug
    enabled
    msgmni has been set to 32768
    alg: No test for cipher_null (cipher_null-generic)
    alg: No test for digest_null (digest_null-generic)
    alg: No test for compress_null (compress_null-generic)
    alg: No test for stdrng (krng)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:20:05.0: Boot video device
    pcieport-driver 0000:00:01.0: setting latency timer to 64
    pcieport-driver 0000:00:01.0: found MSI capability
    pcieport-driver 0000:00:01.0: irq 767 for MSI/MSI-X
    pci_express 0000:00:01.0:pcie00: allocate port service
    pci_express 0000:00:01.0:pcie01: allocate port service
    pcieport-driver 0000:00:05.0: setting latency timer to 64
    pcieport-driver 0000:00:05.0: found MSI capability
    pcieport-driver 0000:00:05.0: irq 766 for MSI/MSI-X
    pci_express 0000:00:05.0:pcie00: allocate port service
    pci_express 0000:00:05.0:pcie01: allocate port service
    pcieport-driver 0000:00:09.0: setting latency timer to 64
    pcieport-driver 0000:00:09.0: found MSI capability
    pcieport-driver 0000:00:09.0: irq 765 for MSI/MSI-X
    pci_express 0000:00:09.0:pcie00: allocate port service
    pci_express 0000:00:09.0:pcie01: allocate port service
    pcieport-driver 0000:00:1c.0: setting latency timer to 64
    pcieport-driver 0000:00:1c.0: found MSI capability
    pcieport-driver 0000:00:1c.0: irq 764 for MSI/MSI-X
    pci_express 0000:00:1c.0:pcie00: allocate port service
    pci_express 0000:00:1c.0:pcie02: allocate port service
    pci_express 0000:00:1c.0:pcie03: allocate port service
    pcieport-driver 0000:09:00.0: setting latency timer to 64
    pci_express 0000:09:00.0:pcie11: allocate port service
    pcieport-driver 0000:0a:00.0: setting latency timer to 64
    pcieport-driver 0000:0a:00.0: found MSI capability
    pcieport-driver 0000:0a:00.0: irq 763 for MSI/MSI-X
    pci_express 0000:0a:00.0:pcie21: allocate port service
    pcieport-driver 0000:0a:02.0: setting latency timer to 64
    pcieport-driver 0000:0a:02.0: found MSI capability
    pcieport-driver 0000:0a:02.0: irq 762 for MSI/MSI-X
    pci_express 0000:0a:02.0:pcie21: allocate port service
    processor ACPI_CPU:00: registered as cooling_device0
    ACPI: Processor [CPU0] (supports 8 throttling states)
    processor ACPI_CPU:01: registered as cooling_device1
    ACPI: Processor [CPU1] (supports 8 throttling states)
    processor ACPI_CPU:02: registered as cooling_device2
    ACPI: Processor [CPU2] (supports 8 throttling states)
    processor ACPI_CPU:03: registered as cooling_device3
    ACPI: Processor [CPU3] (supports 8 throttling states)
    processor ACPI_CPU:04: registered as cooling_device4
    ACPI: Processor [CPU4] (supports 8 throttling states)
    processor ACPI_CPU:05: registered as cooling_device5
    ACPI: Processor [CPU5] (supports 8 throttling states)
    processor ACPI_CPU:06: registered as cooling_device6
    ACPI: Processor [CPU6] (supports 8 throttling states)
    processor ACPI_CPU:07: registered as cooling_device7
    ACPI: Processor [CPU7] (supports 8 throttling states)
    Non-volatile memory driver v1.2
    intel_rng: FWH not detected
    Linux agpgart interface v0.103
    Serial: 8250/16550 driver4 ports, IRQ sharing enabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    Switched to high resolution mode on CPU 6
    Switched to high resolution mode on CPU 1
    Switched to high resolution mode on CPU 3
    Switched to high resolution mode on CPU 7
    Switched to high resolution mode on CPU 2
    Switched to high resolution mode on CPU 4
    Switched to high resolution mode on CPU 5
    Switched to high resolution mode on CPU 0
    serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    brd: module loaded
    Uniform Multi-Platform E-IDE driver
    Driver 'sd' needs updating - please use bus_type methods
    ahci 0000:00:1f.2: version 3.0
    ahci 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
    ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA
    mode
    ahci 0000:00:1f.2: flags: 64bit pm led pmp slum part
    ahci 0000:00:1f.2: setting latency timer to 64
    scsi0 : ahci
    scsi1 : ahci
    scsi2 : ahci
    scsi3 : ahci
    scsi4 : ahci
    scsi5 : ahci
    ata1: SATA max UDMA/133 irq_stat 0x00400040,  irq 23
    ata2: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704580 irq 23
    ata3: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704600 irq 23
    ata4: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704680 irq 23
    ata5: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704700 irq 23
    ata6: SATA max UDMA/133 abar m1024@0xdc704400 port 0xdc704780 irq 23
    ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata1.00: ATA-8: ST3500320AS, SD15, max UDMA/133
    ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
    ata1.00: configured for UDMA/133
    ata2: SATA link down (SStatus 0 SControl 300)
    ata3: SATA link down (SStatus 0 SControl 300)
    ata4: SATA link down (SStatus 0 SControl 300)
    ata5: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    scsi 0:0:0:0: Direct-Access     ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
    sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
    DPO or FUA
    sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
    DPO or FUA
     sda: sda1 sda2 sda3
    sd 0:0:0:0: [sda] Attached SCSI disk
    ata_piix 0000:00:1f.1: version 2.12
    ata_piix 0000:00:1f.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    ata_piix 0000:00:1f.1: setting latency timer to 64
    scsi6 : ata_piix
    scsi7 : ata_piix
    ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1880 irq 14
    ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1888 irq 15
    ata8: port disabled. ignoring.
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    ehci_hcd 0000:00:1d.7: setting latency timer to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
    ehci_hcd 0000:00:1d.7: irq 20, io mem 0xdc704000
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 8 ports detected
    uhci_hcd: USB Universal Host Controller Interface driver
    uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    uhci_hcd 0000:00:1d.0: setting latency timer to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001800
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    uhci_hcd 0000:00:1d.1: setting latency timer to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 21, io base 0x00001820
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
    uhci_hcd 0000:00:1d.2: setting latency timer to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.2: irq 22, io base 0x00001840
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
    uhci_hcd 0000:00:1d.3: setting latency timer to 64
    uhci_hcd 0000:00:1d.3: UHCI Host Controller
    uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.3: irq 23, io base 0x00001860
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    rtc_cmos 00:04: RTC can wake from S4
    rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
    i2c /dev entries driver
    i801_smbus 0000:00:1f.3: PCI INT B -> GSI 23 (level, low) -> IRQ 23
    usbcore: registered new interface driver hiddev
    usbcore: registered new interface driver usbhid
    usbhid: v2.6:USB HID core driver
    TCP cubic registered
    Initializing XFRM netlink socket
    NET: Registered protocol family 17
    drivers/rtc/hctosys.c: unable to open rtc device (rtc)
    Freeing unused kernel memory: 388k freed
    Write protecting the kernel read-only data: 4376k
    EXT3-fs: INFO: recovery required on readonly filesystem.
    EXT3-fs: write access will be enabled during recovery.
    kjournald starting.  Commit interval 5 seconds
    EXT3-fs: recovery complete.
    EXT3-fs: mounted filesystem with ordered data mode.
    input: PC Speaker as /class/input/input0
    Adaptec aacraid driver 1.1-5[2456]-ms
    aacraid 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    aacraid 0000:01:00.0: setting latency timer to 64
    input: Power Button (FF) as /class/input/input1
    ACPI: Power Button (FF) [PWRF]
    input: Power Button (CM) as /class/input/input2
    ACPI: Power Button (CM) [PWRB]
    Intel(R) PRO/1000 Network Driver - version 8.0.6a
    Copyright (c) 1999-2008 Intel Corporation.
    e1000 0000:10:09.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
    AAC0: kernel 5.2-0[16343] Nov 20 2008
    AAC0: monitor 5.2-0[16343]
    AAC0: bios 5.2-0[16343]
    AAC0: serial 8A32108386D
    AAC0: Non-DASD support enabled.
    AAC0: 64bit support enabled.
    AAC0: 64 Bit DAC enabled
    scsi8 : aacraid
    scsi 8:0:0:0: Direct-Access     Adaptec  Mem3             V1.0 PQ: 0 ANSI: 2
    sd 8:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16).
    sd 8:0:0:0: [sdb] 13457403904 512-byte hardware sectors: (6.89 TB/6.26 TiB)
    sd 8:0:0:0: [sdb] Write Protect is off
    sd 8:0:0:0: [sdb] Mode Sense: 06 00 10 00
    sd 8:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO
    and FUA
    sd 8:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16).
    sd 8:0:0:0: [sdb] 13457403904 512-byte hardware sectors: (6.89 TB/6.26 TiB)
    sd 8:0:0:0: [sdb] Write Protect is off
    sd 8:0:0:0: [sdb] Mode Sense: 06 00 10 00
    sd 8:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO
    and FUA
     sdb: unknown partition table
    sd 8:0:0:0: [sdb] Attached SCSI removable disk
    scsi 8:1:0:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:1:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:2:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:3:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:4:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:5:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:6:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:7:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:8:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:9:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI: 5
    scsi 8:1:10:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:11:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:12:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:13:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:14:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:15:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:16:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:17:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:18:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:19:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:20:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:21:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:22:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    scsi 8:1:23:0: Direct-Access     SEAGATE  ST3300655SS      S527 PQ: 1 ANSI:
    5
    e1000: 0000:10:09.0: e1000_probe: (PCI-X:133MHz:64-bit) 00:02:55:53:39:5d
    e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
    e1000 0000:10:0a.0: PCI INT A -> GSI 25 (level, low) -> IRQ 25
    e1000: 0000:10:0a.0: e1000_probe: (PCI-X:133MHz:64-bit) 00:04:23:b4:c5:fb
    e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
    md: Autodetecting RAID arrays.
    md: Scanned 0 and added 0 devices.
    md: autorun ...
    md: ... autorun DONE.
    device-mapper: uevent: version 1.0.3
    device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised:
    dm-devel@redhat.com
    device-mapper: multipath: version 1.0.5 loaded
    EXT3 FS on sda3, internal journal
    kjournald starting.  Commit interval 5 seconds
    EXT3 FS on sda1, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    XFS mounting filesystem sdb
    Starting XFS recovery on filesystem: sdb (logdev: internal)
    Ending XFS recovery on filesystem: sdb (logdev: internal)
    Adding 16779884k swap on /dev/sda2.  Priority:-1 extents:1 across:16779884k
    microcode: CPU0 updated from revision 0x60b to 0x60c, date = 2008-01-19
    microcode: CPU1 updated from revision 0x60b to 0x60c, date = 2008-01-19
    microcode: CPU2 updated from revision 0x60b to 0x60c, date = 2008-01-19
    microcode: CPU3 updated from revision 0x60b to 0x60c, date = 2008-01-19
    microcode: CPU4 updated from revision 0x60b to 0x60c, date = 2008-01-19
    microcode: CPU5 updated from revision 0x60b to 0x60c, date = 2008-01-19
    microcode: CPU6 updated from revision 0x60b to 0x60c, date = 2008-01-19
    microcode: CPU7 updated from revision 0x60b to 0x60c, date = 2008-01-19
    e1000: eth0: e1000_watchdog_task: NIC Link is Up 1000 Mbps Full Duplex, Flow
    Control: RX/TX
    e1000: eth1: e1000_watchdog_task: NIC Link is Up 1000 Mbps Full Duplex, Flow
    Control: RX/TX
    warning: `dbus-daemon' uses 32-bit capabilities (legacy support in use)
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module


    /proc/interrupts:
    root@mem3 ~]# cat /proc/interrupts
               CPU0       CPU1       CPU2       CPU3       CPU4       CPU5      
    CPU6       CPU7      
      0:        129          3          2          0          0         
    0          0          0   IO-APIC-edge      timer
      1:          0          0          0          0          1         
    0          1          0   IO-APIC-edge      i8042
      3:          0          0          1          0          0         
    0          1          0   IO-APIC-edge   
      4:          1          0          0          0          1         
    0          0          0   IO-APIC-edge   
      6:          1          1          0          0          1         
    1          1          0   IO-APIC-edge      floppy
      8:          0          0          0          0          0         
    0          0          1   IO-APIC-edge      rtc0
      9:          0          0          0          0          0         
    0          0          0   IO-APIC-fasteoi   acpi
     12:          3          0          1          1          1         
    1          0          0   IO-APIC-edge      i8042
     14:          0          0          0          0          0         
    0          0          0   IO-APIC-edge      ata_piix
     15:          0          0          0          0          0         
    0          0          0   IO-APIC-edge      ata_piix
     16:       1058        197        352        196       1536     207913      
    1059     207913   IO-APIC-fasteoi   aacraid
     20:          0          0          0          0          0         
    0          0          0   IO-APIC-fasteoi   ehci_hcd:usb1, uhci_hcd:usb2
     21:          0          0          0          0          0         
    0          0          0   IO-APIC-fasteoi   uhci_hcd:usb3
     22:          0          0          0          0          0         
    0          0          0   IO-APIC-fasteoi   uhci_hcd:usb4
     23:        725        721        729        729       3826       1678      
    2183       1687   IO-APIC-fasteoi   ahci, uhci_hcd:usb5
     24:         10         13      12644   13423600         11         14     
    40205         10   IO-APIC-fasteoi   eth0
     25:          4          7          1      28174          4          7   
    6361363          3   IO-APIC-fasteoi   eth1
    NMI:          0          0          0          0          0         
    0          0          0   Non-maskable interrupts
    LOC:    2219823    2228500    2216906    2219457    2238783    2236045   
    2219075    2240538   Local timer interrupts
    RES:        492        491        414       4089        595        742      
    1348        891   Rescheduling interrupts
    CAL:        125        185        184        177        185       
    184        166        117   Function call interrupts
    TLB:       3102       2886       3166      73490       3167      13094     
    25675      14033   TLB shootdowns
    TRM:          0          0          0          0          0         
    0          0          0   Thermal event interrupts
    THR:          0          0          0          0          0         
    0          0          0   Threshold APIC interrupts
    SPU:          0          0          0          0          0         
    0          0          0   Spurious interrupts
    ERR:          0
    MIS:          0



    Lspci -nvvv
    00:00.0 0600: 8086:4003 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0, Cache Line Size: 32 bytes
            Interrupt: pin A routed to IRQ 9
            Capabilities: [50] Power Management version 3
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1
    Enable-
                    Address: fee00000  Data: 0000
            Capabilities: [6c] Express Root Port (Slot-) IRQ 0
                    Device: Supported: MaxPayload 256 bytes, PhantFunc 0,
    ExtTag-
                    Device: Latency L0s <64ns, L1 <1us
                    Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
                    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                    Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0
                    Link: Latency L0s <1us, L1 <4us
                    Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
                    Link: Speed 2.5Gb/s, Width x4
                    Root: Correctable- Non-Fatal- Fatal- PME-
            Capabilities: [100] Advanced Error Reporting

    00:01.0 0604: 8086:4021 (rev 20)
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0, Cache Line Size: 32 bytes
            Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
            I/O behind bridge: 0000f000-00000fff
            Memory behind bridge: dc000000-dc1fffff
            Prefetchable memory behind bridge: 00000000c2000000-00000000c2000000
            Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- <SERR- <PERR-
            BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
            Capabilities: [50] Power Management version 3
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1
    Enable+
                    Address: feeff00c  Data: 4161
            Capabilities: [6c] Express Root Port (Slot-) IRQ 0
                    Device: Supported: MaxPayload 256 bytes, PhantFunc 0,
    ExtTag-
                    Device: Latency L0s <64ns, L1 <1us
                    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                    Link: Supported Speed unknown, Width x16, ASPM L0s L1, Port
    4
                    Link: Latency L0s <1us, L1 <4us
                    Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
                    Link: Speed 2.5Gb/s, Width x8
                    Root: Correctable- Non-Fatal- Fatal- PME-
            Capabilities: [b0] #0d [0000]
            Capabilities: [100] Advanced Error Reporting

    00:05.0 0604: 8086:4025 (rev 20)
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0, Cache Line Size: 32 bytes
            Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
            I/O behind bridge: 0000f000-00000fff
            Memory behind bridge: fff00000-000fffff
            Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
            Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- <SERR- <PERR-
            BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
            Capabilities: [50] Power Management version 3
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1
    Enable+
                    Address: feeff00c  Data: 4169
            Capabilities: [6c] Express Root Port (Slot-) IRQ 0
                    Device: Supported: MaxPayload 256 bytes, PhantFunc 0,
    ExtTag-
                    Device: Latency L0s <64ns, L1 <1us
                    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                    Link: Supported Speed unknown, Width x16, ASPM L0s L1, Port
    8
                    Link: Latency L0s <1us, L1 <4us
                    Link: ASPM Disabled RCB 64 bytes Disabled CommClk+ ExtSynch-
                    Link: Speed 2.5Gb/s, Width x0
                    Root: Correctable- Non-Fatal- Fatal- PME-
            Capabilities: [b0] #0d [0000]
            Capabilities: [100] Advanced Error Reporting

    00:09.0 0604: 8086:4029 (rev 20)
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR+
            Latency: 0, Cache Line Size: 32 bytes
            Bus: primary=00, secondary=09, subordinate=10, sec-latency=0
            I/O behind bridge: 00002000-00002fff
            Memory behind bridge: dc200000-dc3fffff
            Prefetchable memory behind bridge: 00000000c2100000-00000000c2100000
            Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- <SERR- <PERR-
            BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
            Capabilities: [50] Power Management version 3
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1
    Enable+
                    Address: feeff00c  Data: 4171
            Capabilities: [6c] Express Root Port (Slot+) IRQ 0
                    Device: Supported: MaxPayload 256 bytes, PhantFunc 0,
    ExtTag-
                    Device: Latency L0s <64ns, L1 <1us
                    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                    Link: Supported Speed unknown, Width x4, ASPM L0s L1, Port
    12
                    Link: Latency L0s <1us, L1 <4us
                    Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
                    Link: Speed 2.5Gb/s, Width x4
                    Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug-
    Surpise-
                    Slot: Number 0, PowerLimit 0.000000
                    Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
                    Slot: AttnInd Off, PwrInd Off, Power-
                    Root: Correctable- Non-Fatal- Fatal- PME-
            Capabilities: [b0] #0d [0000]
            Capabilities: [100] Advanced Error Reporting

    00:10.0 0600: 8086:4030 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:10.1 0600: 8086:4030 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:10.2 0600: 8086:4030 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:10.3 0600: 8086:4030 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:10.4 0600: 8086:4030 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:11.0 0600: 8086:4031 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:15.0 0600: 8086:4035 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:15.1 0600: 8086:4035 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:16.0 0600: 8086:4036 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:16.1 0600: 8086:4036 (rev 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-

    00:1c.0 0604: 8086:2690 (rev 09)
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0, Cache Line Size: 32 bytes
            Bus: primary=00, secondary=1f, subordinate=1f, sec-latency=0
            I/O behind bridge: 0000f000-00000fff
            Memory behind bridge: fff00000-000fffff
            Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
            Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort+ <SERR- <PERR-
            BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
            Capabilities: [40] Express Root Port (Slot+) IRQ 0
                    Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    ExtTag+
                    Device: Latency L0s unlimited, L1 unlimited
                    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                    Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1
                    Link: Latency L0s <256ns, L1 <4us
                    Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
                    Link: Speed 2.5Gb/s, Width x0
                    Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
    Surpise+
                    Slot: Number 0, PowerLimit 0.000000
                    Slot: Enabled AtnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
                    Slot: AttnInd Off, PwrInd Off, Power-
                    Root: Correctable- Non-Fatal- Fatal- PME-
            Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
    Enable+
                    Address: feeff00c  Data: 4179
            Capabilities: [90] #0d [0000]
            Capabilities: [a0] Power Management version 2
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [100] Virtual Channel
            Capabilities: [180] Unknown (5)

    00:1d.0 0c03: 8086:2688 (rev 09)
            Subsystem: 10f1:5397
            Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0
            Interrupt: pin A routed to IRQ 20
            Region 4: I/O ports at 1800 [size=32]

    00:1d.1 0c03: 8086:2689 (rev 09)
            Subsystem: 10f1:5397
            Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0
            Interrupt: pin B routed to IRQ 21
            Region 4: I/O ports at 1820 [size=32]

    00:1d.2 0c03: 8086:268a (rev 09)
            Subsystem: 10f1:5397
            Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0
            Interrupt: pin C routed to IRQ 22
            Region 4: I/O ports at 1840 [size=32]

    00:1d.3 0c03: 8086:268b (rev 09)
            Subsystem: 10f1:5397
            Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0
            Interrupt: pin D routed to IRQ 23
            Region 4: I/O ports at 1860 [size=32]

    00:1d.7 0c03: 8086:268c (rev 09) (prog-if 20)
            Subsystem: 10f1:5397
            Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0
            Interrupt: pin A routed to IRQ 20
            Region 0: Memory at dc704000 (32-bit, non-prefetchable) [size=1K]
            Capabilities: [50] Power Management version 2
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [58] Debug port

    00:1e.0 0604: 8086:244e (rev d9) (prog-if 01)
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0
            Bus: primary=00, secondary=20, subordinate=20, sec-latency=32
            I/O behind bridge: 00003000-00003fff
            Memory behind bridge: dc400000-dc4fffff
            Prefetchable memory behind bridge: 00000000d8000000-00000000dbf00000
            Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort+ <SERR- <PERR-
            BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
            Capabilities: [50] #0d [0000]

    00:1f.0 0601: 8086:2670 (rev 09)
            Subsystem: 10f1:5397
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0

    00:1f.1 0101: 8086:269e (rev 09) (prog-if 8a)
            Subsystem: 10f1:5397
            Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0
            Interrupt: pin A routed to IRQ 20
            Region 0: I/O ports at 01f0 [size=8]
            Region 1: I/O ports at 03f4 [size=1]
            Region 2: I/O ports at 0170 [size=8]
            Region 3: I/O ports at 0374 [size=1]
            Region 4: I/O ports at 1880 [size=16]

    00:1f.2 0106: 8086:2681 (rev 09) (prog-if 01)
            Subsystem: 10f1:5397
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0
            Interrupt: pin B routed to IRQ 23
            Region 0: I/O ports at 18d0 [size=8]
            Region 1: I/O ports at 18c8 [size=4]
            Region 2: I/O ports at 18c0 [size=8]
            Region 3: I/O ports at 1894 [size=4]
            Region 4: I/O ports at 18a0 [size=32]
            Region 5: Memory at dc704400 (32-bit, non-prefetchable) [size=1K]
            Capabilities: [70] Power Management version 2
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot+,D3cold-)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [a8] #12 [0010]

    00:1f.3 0c05: 8086:269b (rev 09)
            Subsystem: 10f1:5397
            Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Interrupt: pin B routed to IRQ 23
            Region 4: I/O ports at 18e0 [size=32]

    01:00.0 0104: 9005:0285 (rev 09)
            Subsystem: 9005:02d0
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0, Cache Line Size: 32 bytes
            Interrupt: pin A routed to IRQ 16
            Region 0: Memory at dc000000 (64-bit, non-prefetchable) [size=2M]
            [virtual] Expansion ROM at c2000000 [disabled] [size=512K]
            Capabilities: [98] Power Management version 2
                    Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [a0] Message Signalled Interrupts: 64bit+ Queue=0/1
    Enable-
                    Address: 0000000000000000  Data: 0000
            Capabilities: [d0] Express Endpoint IRQ 0
                    Device: Supported: MaxPayload 512 bytes, PhantFunc 0,
    ExtTag-
                    Device: Latency L0s unlimited, L1 <1us
                    Device: AtnBtn- AtnInd- PwrInd-
                    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                    Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                    Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
                    Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
                    Link: Latency L0s <128ns, L1 unlimited
                    Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
                    Link: Speed 2.5Gb/s, Width x8
            Capabilities: [90] Vital Product Data
            Capabilities: [100] Advanced Error Reporting

    09:00.0 0604: 8086:3500 (rev 01)
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0, Cache Line Size: 32 bytes
            Bus: primary=09, secondary=0a, subordinate=0f, sec-latency=0
            I/O behind bridge: 0000f000-00000fff
            Memory behind bridge: fff00000-000fffff
            Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
            Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort+ <SERR- <PERR-
            BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
            Capabilities: [44] Express Upstream Port IRQ 0
                    Device: Supported: MaxPayload 256 bytes, PhantFunc 0,
    ExtTag-
                    Device: Latency L0s <64ns, L1 <1us
                    Device: AtnBtn- AtnInd- PwrInd-
                    Device: SlotPowerLimit 0.000000
                    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                    Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
                    Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
                    Link: Latency L0s unlimited, L1 unlimited
                    Link: ASPM Disabled CommClk- ExtSynch-
                    Link: Speed 2.5Gb/s, Width x4
            Capabilities: [70] Power Management version 2
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [80] #0d [0000]
            Capabilities: [100] Advanced Error Reporting

    09:00.3 0604: 8086:350c (rev 01)
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR+
            Latency: 0, Cache Line Size: 64 bytes
            Bus: primary=09, secondary=10, subordinate=10, sec-latency=64
            I/O behind bridge: 00002000-00002fff
            Memory behind bridge: dc200000-dc2fffff
            Prefetchable memory behind bridge: 00000000c2100000-00000000c2100000
            Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- <SERR- <PERR-
            BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
            Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
                    Device: Supported: MaxPayload 256 bytes, PhantFunc 0,
    ExtTag-
                    Device: Latency L0s <64ns, L1 <1us
                    Device: AtnBtn- AtnInd- PwrInd-
                    Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
                    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                    Device: MaxPayload 128 bytes, MaxReadReq 256 bytes
                    Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
                    Link: Latency L0s unlimited, L1 unlimited
                    Link: ASPM Disabled CommClk- ExtSynch-
                    Link: Speed 2.5Gb/s, Width x4
            Capabilities: [6c] Power Management version 2
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [80] #0d [0000]
            Capabilities: [d8] PCI-X bridge device
                    Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD-
    Freq=133MHz
                    Status: Dev=00:00.3 64bit- 133MHz- SCD- USC- SCO- SRD-
                    Upstream: Capacity=65535 CommitmentLimit=65535
                    Downstream: Capacity=65535 CommitmentLimit=65535
            Capabilities: [100] Advanced Error Reporting

    0a:00.0 0604: 8086:3510 (rev 01)
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0, Cache Line Size: 32 bytes
            Bus: primary=0a, secondary=0b, subordinate=0b, sec-latency=0
            I/O behind bridge: 0000f000-00000fff
            Memory behind bridge: fff00000-000fffff
            Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
            Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- <SERR- <PERR-
            BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
            Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
                    Device: Supported: MaxPayload 256 bytes, PhantFunc 0,
    ExtTag-
                    Device: Latency L0s <64ns, L1 <1us
                    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                    Device: MaxPayload 128 bytes, MaxReadReq 2048 bytes
                    Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
                    Link: Latency L0s <512ns, L1 unlimited
                    Link: ASPM Disabled Disabled CommClk+ ExtSynch-
                    Link: Speed 2.5Gb/s, Width x0
            Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
    Enable+
                    Address: 00000000feeff00c  Data: 4181
            Capabilities: [70] Power Management version 2
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [80] #0d [0000]
            Capabilities: [100] Advanced Error Reporting

    0a:02.0 0604: 8086:3518 (rev 01)
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 0, Cache Line Size: 32 bytes
            Bus: primary=0a, secondary=0f, subordinate=0f, sec-latency=0
            I/O behind bridge: 0000f000-00000fff
            Memory behind bridge: fff00000-000fffff
            Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
            Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort+ <SERR- <PERR-
            BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
            Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
                    Device: Supported: MaxPayload 256 bytes, PhantFunc 0,
    ExtTag-
                    Device: Latency L0s <64ns, L1 <1us
                    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                    Device: MaxPayload 128 bytes, MaxReadReq 2048 bytes
                    Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
                    Link: Latency L0s unlimited, L1 unlimited
                    Link: ASPM Disabled CommClk- ExtSynch-
                    Link: Speed 2.5Gb/s, Width x4
            Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
    Enable+
                    Address: 00000000feeff00c  Data: 4189
            Capabilities: [70] Power Management version 2
                    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [80] #0d [0000]
            Capabilities: [100] Advanced Error Reporting

    10:09.0 0200: 8086:100f (rev 01)
            Subsystem: 1014:0269
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR+
            Latency: 52 (63750ns min), Cache Line Size: 32 bytes
            Interrupt: pin A routed to IRQ 24
            Region 0: Memory at dc280000 (64-bit, non-prefetchable) [size=128K]
            Region 2: Memory at dc200000 (64-bit, non-prefetchable) [size=256K]
            Region 4: I/O ports at 2000 [size=64]
            [virtual] Expansion ROM at c2100000 [disabled] [size=256K]
            Capabilities: [dc] Power Management version 2
                    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
            Capabilities: [e4] PCI-X non-bridge device
                    Command: DPERE- ERO+ RBC=512 OST=1
                    Status: Dev=10:09.0 64bit+ 133MHz+ SCD- USC- DC=simple
    DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
            Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
    Enable-
                    Address: 0000000000000000  Data: 0000

    10:0a.0 0200: 8086:1026 (rev 04)
            Subsystem: 8086:1001
            Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            Latency: 52 (63750ns min), Cache Line Size: 32 bytes
            Interrupt: pin A routed to IRQ 25
            Region 0: Memory at dc2a0000 (64-bit, non-prefetchable) [size=128K]
            Region 2: Memory at dc240000 (64-bit, non-prefetchable) [size=256K]
            Region 4: I/O ports at 2040 [size=64]
            [virtual] Expansion ROM at c2140000 [disabled] [size=256K]
            Capabilities: [dc] Power Management version 2
                    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
                    Status: D0 PME-Enable- DSel=0 DScale=1 PME-
            Capabilities: [e4] PCI-X non-bridge device
                    Command: DPERE- ERO+ RBC=512 OST=1
                    Status: Dev=10:0a.0 64bit+ 133MHz+ SCD- USC- DC=simple
    DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
            Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
    Enable-
                    Address: 0000000000000000  Data: 0000

    20:05.0 0300: 18ca:0020
            Subsystem: 18ca:0020
            Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
            Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
            BIST result: 00
            Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
            Region 1: Memory at dc400000 (32-bit, non-prefetchable) [size=256K]
            Region 2: I/O ports at 3000 [size=128]
            Capabilities: [40] Power Management version 2
                    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    # dmidecode 2.7
    SMBIOS 2.5 present.
    61 structures occupying 1876 bytes.
    Table at 0xBFF60000.

    Handle 0x0000, DMI type 0, 24 bytes.
    BIOS Information
            Vendor: Phoenix Technologies LTD
            Version: V1.03          
            Release Date: 05/19/2008
            Address: 0xE4D20
            Runtime Size: 111328 bytes
            ROM Size: 1024 kB
            Characteristics:
                    PCI is supported
                    PNP is supported
                    APM is supported
                    BIOS is upgradeable
                    BIOS shadowing is allowed
                    ESCD support is available
                    Boot from CD is supported
                    Selectable boot is supported
                    BIOS ROM is socketed
                    EDD is supported
                    ACPI is supported
                    USB legacy is supported
                    LS-120 boot is supported
                    ATAPI Zip drive boot is supported
                    BIOS boot specification is supported
            BIOS Revision: 1.3

    Handle 0x0001, DMI type 1, 27 bytes.
    System Information
            Manufacturer: Empty
            Product Name: Empty
            Version: Empty
            Serial Number: Empty
            UUID: 00000000-0000-0000-0000-F0AB0C00C04D
            Wake-up Type: Power Switch
            SKU Number: Not Specified
            Family: Not Specified

    Handle 0x0002, DMI type 2, 8 bytes.
    Base Board Information
            Manufacturer: TYAN
            Product Name: S5397
            Version: 1.0
            Serial Number: 0123456789

    Handle 0x0003, DMI type 3, 17 bytes.
    Chassis Information
            Manufacturer: Empty
            Type: Other
            Lock: Not Present
            Version: Empty
            Serial Number: Empty
            Asset Tag: Empty
            Boot-up State: Safe
            Power Supply State: Safe
            Thermal State: Safe
            Security Status: None
            OEM Information: 0x00000000

    Handle 0x0004, DMI type 4, 40 bytes.
    Processor Information
            Socket Designation: LGA771
            Type: Central Processor
            Family: Pentium II Xeon
            Manufacturer: Intel
            ID: 76 06 01 00 FF FB EB BF
            Signature: Type 0, Family 6, Model 23, Stepping 6
            Flags:
                    FPU (Floating-point unit on-chip)
                    VME (Virtual mode extension)
                    DE (Debugging extension)
                    PSE (Page size extension)
                    TSC (Time stamp counter)
                    MSR (Model specific registers)
                    PAE (Physical address extension)
                    MCE (Machine check exception)
                    CX8 (CMPXCHG8 instruction supported)
                    APIC (On-chip APIC hardware supported)
                    SEP (Fast system call)
                    MTRR (Memory type range registers)
                    PGE (Page global enable)
                    MCA (Machine check architecture)
                    CMOV (Conditional move instruction supported)
                    PAT (Page attribute table)
                    PSE-36 (36-bit page size extension)
                    CLFSH (CLFLUSH instruction supported)
                    DS (Debug store)
                    ACPI (ACPI supported)
                    MMX (MMX technology supported)
                    FXSR (Fast floating-point save and restore)
                    SSE (Streaming SIMD extensions)
                    SSE2 (Streaming SIMD extensions 2)
                    SS (Self-snoop)
                    HTT (Hyper-threading technology)
                    TM (Thermal monitor supported)
                    PBE (Pending break enabled)
            Version:  
            Voltage: 1.2 V
            External Clock: Unknown
            Max Speed: 3800 MHz
            Current Speed: 2660 MHz
            Status: Populated, Enabled
            Upgrade: <OUT OF SPEC>
            L1 Cache Handle: 0x0006
            L2 Cache Handle: 0x0007
            L3 Cache Handle: Not Provided
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0005, DMI type 4, 40 bytes.
    Processor Information
            Socket Designation: .
            Type: Central Processor
            Family: Pentium II Xeon
            Manufacturer: .
            ID: 76 06 01 00 FF FB EB BF
            Signature: Type 0, Family 6, Model 23, Stepping 6
            Flags:
                    FPU (Floating-point unit on-chip)
                    VME (Virtual mode extension)
                    DE (Debugging extension)
                    PSE (Page size extension)
                    TSC (Time stamp counter)
                    MSR (Model specific registers)
                    PAE (Physical address extension)
                    MCE (Machine check exception)
                    CX8 (CMPXCHG8 instruction supported)
                    APIC (On-chip APIC hardware supported)
                    SEP (Fast system call)
                    MTRR (Memory type range registers)
                    PGE (Page global enable)
                    MCA (Machine check architecture)
                    CMOV (Conditional move instruction supported)
                    PAT (Page attribute table)
                    PSE-36 (36-bit page size extension)
                    CLFSH (CLFLUSH instruction supported)
                    DS (Debug store)
                    ACPI (ACPI supported)
                    MMX (MMX technology supported)
                    FXSR (Fast floating-point save and restore)
                    SSE (Streaming SIMD extensions)
                    SSE2 (Streaming SIMD extensions 2)
                    SS (Self-snoop)
                    HTT (Hyper-threading technology)
                    TM (Thermal monitor supported)
                    PBE (Pending break enabled)
            Version: X
            Voltage: 1.2 V
            External Clock: Unknown
            Max Speed: 3800 MHz
            Current Speed: 2660 MHz
            Status: Populated, Enabled
            Upgrade: <OUT OF SPEC>
            L1 Cache Handle: 0x0008
            L2 Cache Handle: 0x0009
            L3 Cache Handle: Not Provided
            Serial Number: Not Specified
            Asset Tag: <BAD INDEX>
            Part Number: <BAD INDEX>

    Handle 0x4C02, DMI type 2, 2 bytes.
    Base Board Information

    Handle 0x0007, DMI type 7, 19 bytes.
    Cache Information
            Socket Designation: L2 Cache
            Configuration: Enabled, Socketed, Level 2
            Operational Mode: Write Back
            Location: Internal
            Installed Size: 12288 KB
            Maximum Size: 8192 KB
            Supported SRAM Types:
                    Burst
                    Pipeline Burst
                    Asynchronous
            Installed SRAM Type: Burst
            Speed: Unknown
            Error Correction Type: Unknown
            System Type: Unknown
            Associativity: Unknown

    Handle 0x0008, DMI type 7, 19 bytes.
    Cache Information
            Socket Designation: L1 Cache
            Configuration: Enabled, Socketed, Level 1
            Operational Mode: Write Back
            Location: Internal
            Installed Size: 16 KB
            Maximum Size: 16 KB
            Supported SRAM Types:
                    Burst
                    Pipeline Burst
                    Asynchronous
            Installed SRAM Type: Asynchronous
            Speed: Unknown
            Error Correction Type: Unknown
            System Type: Unknown
            Associativity: Unknown

    Handle 0x0009, DMI type 7, 19 bytes.
    Cache Information
            Socket Designation: L2 Cache
            Configuration: Enabled, Socketed, Level 2
            Operational Mode: Write Back
            Location: Internal
            Installed Size: 12288 KB
            Maximum Size: 8192 KB
            Supported SRAM Types:
                    Burst
                    Pipeline Burst
                    Asynchronous
            Installed SRAM Type: Burst
            Speed: Unknown
            Error Correction Type: Unknown
            System Type: Unknown
            Associativity: Unknown

    Handle 0x000A, DMI type 8, 9 bytes.
    Port Connector Information
            Internal Reference Designator: J4
            Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
            External Reference Designator: COM 1
            External Connector Type: DB-9 male
            Port Type: Serial Port 16550A Compatible

    Handle 0x000B, DMI type 8, 9 bytes.
    Port Connector Information
            Internal Reference Designator: J20
            Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
            External Reference Designator: COM 2
            External Connector Type: DB-9 male
            Port Type: Serial Port 16550A Compatible

    Handle 0x000C, DMI type 8, 9 bytes.
    Port Connector Information
            Internal Reference Designator: J1
            Internal Connector Type: None
            External Reference Designator: Keyboard
            External Connector Type: Circular DIN-8 male
            Port Type: Keyboard Port

    Handle 0x000D, DMI type 8, 9 bytes.
    Port Connector Information
            Internal Reference Designator: J1
            Internal Connector Type: None
            External Reference Designator: PS/2 Mouse
            External Connector Type: Circular DIN-8 male
            Port Type: Keyboard Port

    Handle 0x000E, DMI type 9, 13 bytes.
    System Slot Information
            Designation: PCI/33 Slot #1 - J1B1
            Type: 32-bit PCI
            Current Usage: Available
            Length: Long
            ID: 1
            Characteristics:
                    5.0 V is provided
                    3.3 V is provided

    Handle 0x000F, DMI type 9, 13 bytes.
    System Slot Information
            Designation: PCIE Slot #2 - J2B1
            Type: 32-bit PCI Express
            Current Usage: Available
            Length: Long
            Characteristics:
                    5.0 V is provided
                    3.3 V is provided

    Handle 0x0010, DMI type 9, 13 bytes.
    System Slot Information
            Designation: PCIE Slot #3 - J2B2
            Type: 32-bit PCI Express
            Current Usage: Available
            Length: Long
            Characteristics:
                    5.0 V is provided
                    3.3 V is provided

    Handle 0x0011, DMI type 9, 13 bytes.
    System Slot Information
            Designation: PCIE Slot #4 - J3B3
            Type: 32-bit PCI Express
            Current Usage: In Use
            Length: Long
            Characteristics:
                    5.0 V is provided
                    3.3 V is provided

    Handle 0x0012, DMI type 9, 13 bytes.
    System Slot Information
            Designation: PCIE Slot #5 - J3B2
            Type: 32-bit PCI-X
            Current Usage: In Use
            Length: Long
            ID: 5
            Characteristics:
                    5.0 V is provided
                    3.3 V is provided

    Handle 0x0013, DMI type 9, 13 bytes.
    System Slot Information
            Designation: PCIE Slot #6 - J4B1
            Type: 32-bit PCI Express
            Current Usage: Available
            Length: Long
            Characteristics:
                    5.0 V is provided
                    3.3 V is provided

    Handle 0x0014, DMI type 10, 6 bytes.
    On Board Device Information
            Type: Sound
            Status: Disabled
            Description: RealTek

    Handle 0x0015, DMI type 11, 5 bytes.
    OEM Strings
            String 1: 0
            String 2: 0
            String 3: .........................

    Handle 0x0016, DMI type 15, 29 bytes.
    System Event Log
            Area Length: 32 bytes
            Header Start Offset: 0x0000
            Header Length: 16 bytes
            Data Start Offset: 0x0010
            Access Method: General-purpose non-volatile data functions
            Access Address: 0x0000
            Status: Valid, Not Full
            Change Token: 0x0000008F
            Header Format: Type 1
            Supported Log Type Descriptors: 3
            Descriptor 1: POST error
            Data Format 1: POST results bitmap
            Descriptor 2: Single-bit ECC memory error
            Data Format 2: Multiple-event
            Descriptor 3: Multi-bit ECC memory error
            Data Format 3: Multiple-event

    Handle 0x0017, DMI type 16, 15 bytes.
    Physical Memory Array
            Location: System Board Or Motherboard
            Use: System Memory
            Error Correction Type: None
            Maximum Capacity: 64 GB
            Error Information Handle: Not Provided
            Number Of Devices: 4

    Handle 0x0018, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: 72 bits
            Data Width: 64 bits
            Size: 1573 MB
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM1
            Bank Locator: DIMM1
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0019, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: 72 bits
            Data Width: 64 bits
            Size: 1573 MB
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM2
            Bank Locator: DIMM2
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x001A, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: 72 bits
            Data Width: 64 bits
            Size: 1573 MB
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM3
            Bank Locator: DIMM3
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x001B, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: 72 bits
            Data Width: 64 bits
            Size: 1573 MB
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM4
            Bank Locator: DIMM4
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x001C, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: 72 bits
            Data Width: 64 bits
            Size: 1573 MB
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM5
            Bank Locator: DIMM5
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x001D, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: 72 bits
            Data Width: 64 bits
            Size: 1573 MB
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM6
            Bank Locator: DIMM6
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x001E, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: 72 bits
            Data Width: 64 bits
            Size: 1573 MB
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM7
            Bank Locator: DIMM7
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x001F, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: 72 bits
            Data Width: 64 bits
            Size: 1573 MB
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM8
            Bank Locator: DIMM8
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0020, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: Unknown
            Data Width: Unknown
            Size: No Module Installed
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM9
            Bank Locator: DIMM9
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0021, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: Unknown
            Data Width: Unknown
            Size: No Module Installed
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM10
            Bank Locator: DIMM10
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0022, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: Unknown
            Data Width: Unknown
            Size: No Module Installed
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM11
            Bank Locator: DIMM11
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0023, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: Unknown
            Data Width: Unknown
            Size: No Module Installed
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM12
            Bank Locator: DIMM12
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0024, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: Unknown
            Data Width: Unknown
            Size: No Module Installed
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM13
            Bank Locator: DIMM13
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0025, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: Unknown
            Data Width: Unknown
            Size: No Module Installed
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM14
            Bank Locator: DIMM14
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0026, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: Unknown
            Data Width: Unknown
            Size: No Module Installed
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM15
            Bank Locator: DIMM15
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0027, DMI type 17, 27 bytes.
    Memory Device
            Array Handle: 0x0017
            Error Information Handle: No Error
            Total Width: Unknown
            Data Width: Unknown
            Size: No Module Installed
            Form Factor: <OUT OF SPEC>
            Set: 1
            Locator: DIMM16
            Bank Locator: DIMM16
            Type: <OUT OF SPEC>
            Type Detail: Synchronous
            Speed: 533 MHz (1.9 ns)
            Manufacturer: Not Specified
            Serial Number: Not Specified
            Asset Tag: Not Specified
            Part Number: Not Specified

    Handle 0x0028, DMI type 19, 15 bytes.
    Memory Array Mapped Address
            Starting Address: 0x00000000000
            Ending Address: 0x003127FFFFF
            Range Size: 12584 MB
            Physical Array Handle: 0x0017
            Partition Width: 0

    Handle 0x0029, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x00000000000
            Ending Address: 0x000624FFFFF
            Range Size: 1573 MB
            Physical Device Handle: 0x0018
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x002A, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x00062500000
            Ending Address: 0x000C49FFFFF
            Range Size: 1573 MB
            Physical Device Handle: 0x0019
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x002B, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x000C4A00000
            Ending Address: 0x00126EFFFFF
            Range Size: 1573 MB
            Physical Device Handle: 0x001A
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x002C, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x00126F00000
            Ending Address: 0x001893FFFFF
            Range Size: 1573 MB
            Physical Device Handle: 0x001B
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x002D, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x00189400000
            Ending Address: 0x001EB8FFFFF
            Range Size: 1573 MB
            Physical Device Handle: 0x001C
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x002E, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x001EB900000
            Ending Address: 0x0024DDFFFFF
            Range Size: 1573 MB
            Physical Device Handle: 0x001D
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x002F, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x0024DE00000
            Ending Address: 0x002B02FFFFF
            Range Size: 1573 MB
            Physical Device Handle: 0x001E
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0030, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x002B0300000
            Ending Address: 0x003127FFFFF
            Range Size: 1573 MB
            Physical Device Handle: 0x001F
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0031, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x003127FFC00
            Ending Address: 0x003127FFFFF
            Range Size: 1 kB
            Physical Device Handle: 0x0020
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0032, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x003127FFC00
            Ending Address: 0x003127FFFFF
            Range Size: 1 kB
            Physical Device Handle: 0x0021
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0033, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x003127FFC00
            Ending Address: 0x003127FFFFF
            Range Size: 1 kB
            Physical Device Handle: 0x0022
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0034, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x003127FFC00
            Ending Address: 0x003127FFFFF
            Range Size: 1 kB
            Physical Device Handle: 0x0023
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0035, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x003127FFC00
            Ending Address: 0x003127FFFFF
            Range Size: 1 kB
            Physical Device Handle: 0x0024
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0036, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x003127FFC00
            Ending Address: 0x003127FFFFF
            Range Size: 1 kB
            Physical Device Handle: 0x0025
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0037, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x003127FFC00
            Ending Address: 0x003127FFFFF
            Range Size: 1 kB
            Physical Device Handle: 0x0026
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0038, DMI type 20, 19 bytes.
    Memory Device Mapped Address
            Starting Address: 0x003127FFC00
            Ending Address: 0x003127FFFFF
            Range Size: 1 kB
            Physical Device Handle: 0x0027
            Memory Array Mapped Address Handle: 0x0028
            Partition Row Position: Unknown
            Interleave Position: Unknown
            Interleaved Data Depth: Unknown

    Handle 0x0039, DMI type 23, 13 bytes.
    System Reset
            Status: Enabled
            Watchdog Timer: Present
            Boot Option: Do Not Reboot
            Boot Option On Limit: Do Not Reboot
            Reset Count: Unknown
            Reset Limit: Unknown
            Timer Interval: Unknown
            Timeout: Unknown

    Handle 0x003A, DMI type 32, 20 bytes.
    System Boot Information
            Status: <OUT OF SPEC>

    Handle 0x003B, DMI type 38, 18 bytes.
    IPMI Device Information
            Interface Type: Unknown
            Specification Version: 0.0
            I2C Slave Address: 0x00
            NV Storage Device: Not Present
            Base Address: 0x0000000000000000 (Memory-mapped)
            Register Spacing: Successive Byte Boundaries
            Interrupt Polarity: Active Low
            Interrupt Trigger Mode: Edge

    Handle 0x003C, DMI type 127, 4 bytes.
    End Of Table

    .config:

    CONFIG_64BIT=y
    CONFIG_ACPI_AC=m
    CONFIG_ACPI_BATTERY=m
    CONFIG_ACPI_BLACKLIST_YEAR=0
    CONFIG_ACPI_BUTTON=m
    CONFIG_ACPI_DOCK=y
    CONFIG_ACPI_FAN=y
    CONFIG_ACPI_PROCESSOR=y
    CONFIG_ACPI_PROC_EVENT=y
    CONFIG_ACPI_PROCFS_POWER=y
    CONFIG_ACPI_SYSFS_POWER=y
    CONFIG_ACPI_SYSTEM=y
    CONFIG_ACPI_THERMAL=y
    CONFIG_ACPI=y
    CONFIG_AGP_AMD64=y
    CONFIG_AGP_INTEL=y
    CONFIG_AGP_SIS=y
    CONFIG_AGP_VIA=y
    CONFIG_AGP=y
    CONFIG_AIO=y
    CONFIG_AMIGA_PARTITION=y
    CONFIG_ANON_INODES=y
    CONFIG_ARCH_DEFCONFIG="arch/x86/configs/x86_64_defconfig"
    CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
    CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
    CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
    CONFIG_ARCH_HAS_CPU_RELAX=y
    CONFIG_ARCH_HAS_DEFAULT_IDLE=y
    CONFIG_ARCH_HIBERNATION_POSSIBLE=y
    CONFIG_ARCH_MAY_HAVE_PC_FDC=y
    CONFIG_ARCH_PHYS_ADDR_T_64BIT=y
    CONFIG_ARCH_POPULATES_NODE_MAP=y
    CONFIG_ARCH_SELECT_MEMORY_MODEL=y
    CONFIG_ARCH_SPARSEMEM_DEFAULT=y
    CONFIG_ARCH_SPARSEMEM_ENABLE=y
    CONFIG_ARCH_SUPPORTS_MSI=y
    CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y
    CONFIG_ARCH_SUSPEND_POSSIBLE=y
    CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
    CONFIG_ASYNC_CORE=m
    CONFIG_ASYNC_MEMCPY=m
    CONFIG_ASYNC_XOR=m
    CONFIG_ATA_ACPI=y
    CONFIG_ATA_PIIX=y
    CONFIG_ATA_SFF=y
    CONFIG_ATA=y
    CONFIG_AUDIT_ARCH=y
    CONFIG_AUDITSYSCALL=y
    CONFIG_AUDIT_TREE=y
    CONFIG_AUDIT=y
    CONFIG_AUTOFS4_FS=y
    CONFIG_BASE_FULL=y
    CONFIG_BASE_SMALL=0
    CONFIG_BINFMT_ELF=y
    CONFIG_BINFMT_MISC=y
    CONFIG_BITREVERSE=y
    CONFIG_BLK_DEV_CRYPTOLOOP=m
    CONFIG_BLK_DEV_DM=m
    CONFIG_BLK_DEV_FD=y
    CONFIG_BLK_DEV_IDECD=m
    CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
    CONFIG_BLK_DEV_IDEDMA_PCI=y
    CONFIG_BLK_DEV_IDEDMA_SFF=y
    CONFIG_BLK_DEV_IDEDMA=y
    CONFIG_BLK_DEV_IDEPCI=y
    CONFIG_BLK_DEV_IDESCSI=m
    CONFIG_BLK_DEV_INITRD=y
    CONFIG_BLK_DEV_IO_TRACE=y
    CONFIG_BLK_DEV_LOOP=m
    CONFIG_BLK_DEV_MD=y
    CONFIG_BLK_DEV_NBD=m
    CONFIG_BLK_DEV_PIIX=m
    CONFIG_BLK_DEV_RAM_COUNT=16
    CONFIG_BLK_DEV_RAM_SIZE=16384
    CONFIG_BLK_DEV_RAM=y
    CONFIG_BLK_DEV_SD=y
    CONFIG_BLK_DEV=y
    CONFIG_BLOCK_COMPAT=y
    CONFIG_BLOCK=y
    CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
    CONFIG_BOUNCE=y
    CONFIG_BSD_DISKLABEL=y
    CONFIG_BSD_PROCESS_ACCT_V3=y
    CONFIG_BSD_PROCESS_ACCT=y
    CONFIG_BUG=y
    CONFIG_CC_OPTIMIZE_FOR_SIZE=y
    CONFIG_CLASSIC_RCU=y
    CONFIG_CLOCKSOURCE_WATCHDOG=y
    CONFIG_COMPAT_BINFMT_ELF=y
    CONFIG_COMPAT_BRK=y
    CONFIG_COMPAT_FOR_U64_ALIGNMENT=y
    CONFIG_COMPAT_VDSO=y
    CONFIG_COMPAT=y
    CONFIG_CONFIGFS_FS=m
    CONFIG_CONNECTOR=y
    CONFIG_CONSOLE_TRANSLATIONS=y
    CONFIG_CPU_SUP_AMD=y
    CONFIG_CPU_SUP_CENTAUR_64=y
    CONFIG_CPU_SUP_INTEL=y
    CONFIG_CRAMFS=m
    CONFIG_CRC16=y
    CONFIG_CRC32=y
    CONFIG_CRC_CCITT=m
    CONFIG_CRC_ITU_T=m
    CONFIG_CRYPTO_AEAD2=y
    CONFIG_CRYPTO_AEAD=y
    CONFIG_CRYPTO_AES_X86_64=y
    CONFIG_CRYPTO_AES=y
    CONFIG_CRYPTO_ALGAPI2=y
    CONFIG_CRYPTO_ALGAPI=y
    CONFIG_CRYPTO_ANUBIS=y
    CONFIG_CRYPTO_ARC4=y
    CONFIG_CRYPTO_AUTHENC=y
    CONFIG_CRYPTO_BLKCIPHER2=y
    CONFIG_CRYPTO_BLKCIPHER=y
    CONFIG_CRYPTO_BLOWFISH=y
    CONFIG_CRYPTO_CAST5=y
    CONFIG_CRYPTO_CAST6=y
    CONFIG_CRYPTO_CBC=y
    CONFIG_CRYPTO_CCM=y
    CONFIG_CRYPTO_CRC32C=y
    CONFIG_CRYPTO_CTR=y
    CONFIG_CRYPTO_DEFLATE=y
    CONFIG_CRYPTO_DES=y
    CONFIG_CRYPTO_ECB=y
    CONFIG_CRYPTO_HASH2=y
    CONFIG_CRYPTO_HASH=y
    CONFIG_CRYPTO_HMAC=y
    CONFIG_CRYPTO_HW=y
    CONFIG_CRYPTO_KHAZAD=y
    CONFIG_CRYPTO_MANAGER2=y
    CONFIG_CRYPTO_MANAGER=y
    CONFIG_CRYPTO_MD4=y
    CONFIG_CRYPTO_MD5=y
    CONFIG_CRYPTO_MICHAEL_MIC=y
    CONFIG_CRYPTO_NULL=y
    CONFIG_CRYPTO_RNG2=y
    CONFIG_CRYPTO_RNG=y
    CONFIG_CRYPTO_SEQIV=y
    CONFIG_CRYPTO_SERPENT=y
    CONFIG_CRYPTO_SHA1=y
    CONFIG_CRYPTO_SHA256=y
    CONFIG_CRYPTO_SHA512=y
    CONFIG_CRYPTO_TEA=y
    CONFIG_CRYPTO_TGR192=y
    CONFIG_CRYPTO_TWOFISH_COMMON=y
    CONFIG_CRYPTO_TWOFISH=y
    CONFIG_CRYPTO_WP512=y
    CONFIG_CRYPTO_XCBC=y
    CONFIG_CRYPTO=y
    CONFIG_DCA=y
    CONFIG_DEBUG_BUGVERBOSE=y
    CONFIG_DEBUG_FS=y
    CONFIG_DEBUG_KERNEL=y
    CONFIG_DEBUG_MEMORY_INIT=y
    CONFIG_DEBUG_RODATA=y
    CONFIG_DEFAULT_CFQ=y
    CONFIG_DEFAULT_IO_DELAY_TYPE=0
    CONFIG_DEFAULT_IOSCHED="cfq"
    CONFIG_DEFAULT_TCP_CONG="cubic"
    CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
    CONFIG_DETECT_SOFTLOCKUP=y
    CONFIG_DEVKMEM=y
    CONFIG_DEVPORT=y
    CONFIG_DLM_DEBUG=y
    CONFIG_DLM=m
    CONFIG_DMADEVICES=y
    CONFIG_DMA_ENGINE=y
    CONFIG_DMAR_FLOPPY_WA=y
    CONFIG_DMAR_GFX_WA=y
    CONFIG_DMAR=y
    CONFIG_DM_CRYPT=m
    CONFIG_DMIID=y
    CONFIG_DMI=y
    CONFIG_DM_MIRROR=m
    CONFIG_DM_MULTIPATH=m
    CONFIG_DM_SNAPSHOT=m
    CONFIG_DM_UEVENT=y
    CONFIG_DM_ZERO=m
    CONFIG_DNOTIFY=y
    CONFIG_DUMMY_CONSOLE=y
    CONFIG_DUMMY=m
    CONFIG_E1000=m
    CONFIG_EARLY_PRINTK=y
    CONFIG_EDAC_E752X=m
    CONFIG_EDAC_I3000=m
    CONFIG_EDAC_I5000=m
    CONFIG_EDAC_MM_EDAC=m
    CONFIG_EDAC=y
    CONFIG_EDD=m
    CONFIG_EFI_PARTITION=y
    CONFIG_ELF_CORE=y
    CONFIG_ENABLE_MUST_CHECK=y
    CONFIG_ENABLE_WARN_DEPRECATED=y
    CONFIG_EPOLL=y
    CONFIG_EVENTFD=y
    CONFIG_EXPERIMENTAL=y
    CONFIG_EXPORTFS=m
    CONFIG_EXT2_FS_POSIX_ACL=y
    CONFIG_EXT2_FS_SECURITY=y
    CONFIG_EXT2_FS_XATTR=y
    CONFIG_EXT2_FS_XIP=y
    CONFIG_EXT2_FS=y
    CONFIG_EXT3_FS_POSIX_ACL=y
    CONFIG_EXT3_FS_SECURITY=y
    CONFIG_EXT3_FS_XATTR=y
    CONFIG_EXT3_FS=y
    CONFIG_EXT4_FS_XATTR=y
    CONFIG_EXT4_FS=y
    CONFIG_EXTRA_FIRMWARE=""
    CONFIG_FAST_CMPXCHG_LOCAL=y
    CONFIG_FAT_DEFAULT_CODEPAGE=437
    CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
    CONFIG_FAT_FS=m
    CONFIG_FB_BOOT_VESA_SUPPORT=y
    CONFIG_FB_CFB_COPYAREA=y
    CONFIG_FB_CFB_FILLRECT=y
    CONFIG_FB_CFB_IMAGEBLIT=y
    CONFIG_FB_DDC=m
    CONFIG_FB_INTEL_I2C=y
    CONFIG_FB_INTEL=m
    CONFIG_FB_MODE_HELPERS=y
    CONFIG_FB_TILEBLITTING=y
    CONFIG_FB_VESA=y
    CONFIG_FB=y
    CONFIG_FILE_LOCKING=y
    CONFIG_FIRMWARE_IN_KERNEL=y
    CONFIG_FIRMWARE_MEMMAP=y
    CONFIG_FIX_EARLYCON_MEM=y
    CONFIG_FONT_8x16=y
    CONFIG_FONT_8x8=y
    CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
    CONFIG_FRAMEBUFFER_CONSOLE=y
    CONFIG_FRAME_WARN=2048
    CONFIG_FS_MBCACHE=y
    CONFIG_FS_POSIX_ACL=y
    CONFIG_FS_XIP=y
    CONFIG_FTL=m
    CONFIG_FUTEX=y
    CONFIG_FW_LOADER=y
    CONFIG_GART_IOMMU=y
    CONFIG_GENERIC_BUG=y
    CONFIG_GENERIC_CALIBRATE_DELAY=y
    CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
    CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
    CONFIG_GENERIC_CLOCKEVENTS=y
    CONFIG_GENERIC_CMOS_UPDATE=y
    CONFIG_GENERIC_FIND_FIRST_BIT=y
    CONFIG_GENERIC_FIND_NEXT_BIT=y
    CONFIG_GENERIC_HARDIRQS=y
    CONFIG_GENERIC_HWEIGHT=y
    CONFIG_GENERIC_IOMAP=y
    CONFIG_GENERIC_IRQ_PROBE=y
    CONFIG_GENERIC_ISA_DMA=y
    CONFIG_GENERIC_PENDING_IRQ=y
    CONFIG_GENERIC_TIME_VSYSCALL=y
    CONFIG_GENERIC_TIME=y
    CONFIG_HANGCHECK_TIMER=m
    CONFIG_HAS_DMA=y
    CONFIG_HAS_IOMEM=y
    CONFIG_HAS_IOPORT=y
    CONFIG_HAVE_ARCH_KGDB=y
    CONFIG_HAVE_ARCH_TRACEHOOK=y
    CONFIG_HAVE_CPUMASK_OF_CPU_MAP=y
    CONFIG_HAVE_DYNAMIC_FTRACE=y
    CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
    CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
    CONFIG_HAVE_FUNCTION_TRACER=y
    CONFIG_HAVE_IDE=y
    CONFIG_HAVE_IOREMAP_PROT=y
    CONFIG_HAVE_KPROBES=y
    CONFIG_HAVE_KRETPROBES=y
    CONFIG_HAVE_KVM=y
    CONFIG_HAVE_LATENCYTOP_SUPPORT=y
    CONFIG_HAVE_MEMORY_PRESENT=y
    CONFIG_HAVE_OPROFILE=y
    CONFIG_HAVE_SETUP_PER_CPU_AREA=y
    CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
    CONFIG_HFS_FS=m
    CONFIG_HFSPLUS_FS=m
    CONFIG_HID_A4TECH=y
    CONFIG_HID_APPLE=y
    CONFIG_HID_BELKIN=y
    CONFIG_HID_BRIGHT=y
    CONFIG_HID_CHERRY=y
    CONFIG_HID_CHICONY=y
    CONFIG_HID_COMPAT=y
    CONFIG_HID_CYPRESS=y
    CONFIG_HID_DEBUG=y
    CONFIG_HID_DELL=y
    CONFIG_HID_EZKEY=y
    CONFIG_HID_GYRATION=y
    CONFIG_HID_LOGITECH=y
    CONFIG_HID_MICROSOFT=y
    CONFIG_HID_MONTEREY=y
    CONFIG_HID_PANTHERLORD=y
    CONFIG_HID_PETALYNX=y
    CONFIG_HID_PID=y
    CONFIG_HID_SAMSUNG=y
    CONFIG_HID_SONY=y
    CONFIG_HID_SUNPLUS=y
    CONFIG_HID_SUPPORT=y
    CONFIG_HID=y
    CONFIG_HIGH_RES_TIMERS=y
    CONFIG_HOTPLUG=y
    CONFIG_HPET_EMULATE_RTC=y
    CONFIG_HPET_TIMER=y
    CONFIG_HPET=y
    CONFIG_HT_IRQ=y
    CONFIG_HUGETLBFS=y
    CONFIG_HUGETLB_PAGE=y
    CONFIG_HW_CONSOLE=y
    CONFIG_HWMON=m
    CONFIG_HWMON_VID=m
    CONFIG_HW_RANDOM_INTEL=y
    CONFIG_HW_RANDOM=y
    CONFIG_HZ=1000
    CONFIG_HZ_1000=y
    CONFIG_I2C_ALGOBIT=m
    CONFIG_I2C_BOARDINFO=y
    CONFIG_I2C_CHARDEV=y
    CONFIG_I2C_HELPER_AUTO=y
    CONFIG_I2C_I801=y
    CONFIG_I2C=y
    CONFIG_IA32_AOUT=y
    CONFIG_IA32_EMULATION=y
    CONFIG_IDE_ATAPI=y
    CONFIG_IDE_PROC_FS=y
    CONFIG_IDE_TASK_IOCTL=y
    CONFIG_IDE=y
    CONFIG_IKCONFIG=y
    CONFIG_INET_DIAG=y
    CONFIG_INET_LRO=y
    CONFIG_INET_TCP_DIAG=y
    CONFIG_INET=y
    CONFIG_INIT_ENV_ARG_LIMIT=32
    CONFIG_INITRAMFS_SOURCE=""
    CONFIG_INOTIFY_USER=y
    CONFIG_INOTIFY=y
    CONFIG_INPUT_EVDEV=y
    CONFIG_INPUT_FF_MEMLESS=y
    CONFIG_INPUT_KEYBOARD=y
    CONFIG_INPUT_MISC=y
    CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
    CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
    CONFIG_INPUT_MOUSEDEV=y
    CONFIG_INPUT_MOUSE=y
    CONFIG_INPUT_PCSPKR=m
    CONFIG_INPUT_POLLDEV=m
    CONFIG_INPUT_UINPUT=m
    CONFIG_INPUT=y
    CONFIG_INTEL_IOATDMA=y
    CONFIG_INTR_REMAP=y
    CONFIG_IO_DELAY_0X80=y
    CONFIG_IO_DELAY_TYPE_0X80=0
    CONFIG_IO_DELAY_TYPE_0XED=1
    CONFIG_IO_DELAY_TYPE_NONE=3
    CONFIG_IO_DELAY_TYPE_UDELAY=2
    CONFIG_IOMMU_HELPER=y
    CONFIG_IOSCHED_AS=y
    CONFIG_IOSCHED_CFQ=y
    CONFIG_IOSCHED_DEADLINE=y
    CONFIG_IOSCHED_NOOP=y
    CONFIG_IPC_NS=y
    CONFIG_IP_FIB_HASH=y
    CONFIG_IPMI_DEVICE_INTERFACE=m
    CONFIG_IPMI_HANDLER=m
    CONFIG_IPMI_PANIC_EVENT=y
    CONFIG_IPMI_PANIC_STRING=y
    CONFIG_IPMI_POWEROFF=m
    CONFIG_IPMI_SI=m
    CONFIG_IPMI_WATCHDOG=m
    CONFIG_IP_SCTP=m
    CONFIG_ISA_DMA_API=y
    CONFIG_ISO9660_FS=y
    CONFIG_JBD2=y
    CONFIG_JBD=y
    CONFIG_JFFS2_FS_DEBUG=0
    CONFIG_JFFS2_FS=m
    CONFIG_JFFS2_FS_WRITEBUFFER=y
    CONFIG_JFFS2_RTIME=y
    CONFIG_JFFS2_SUMMARY=y
    CONFIG_JFFS2_ZLIB=y
    CONFIG_JOLIET=y
    CONFIG_K8_NB=y
    CONFIG_KALLSYMS_EXTRA_PASS=y
    CONFIG_KALLSYMS=y
    CONFIG_KARMA_PARTITION=y
    CONFIG_KEYBOARD_ATKBD=y
    CONFIG_KMOD=y
    CONFIG_KPROBES=y
    CONFIG_KRETPROBES=y
    CONFIG_LEDS_CLASS=y
    CONFIG_LEDS_TRIGGER_HEARTBEAT=m
    CONFIG_LEDS_TRIGGERS=y
    CONFIG_LEDS_TRIGGER_TIMER=m
    CONFIG_LIBCRC32C=y
    CONFIG_LOCALVERSION=""
    CONFIG_LOCKDEP_SUPPORT=y
    CONFIG_LOCKD=m
    CONFIG_LOCKD_V4=y
    CONFIG_LOCK_KERNEL=y
    CONFIG_LOG_BUF_SHIFT=18
    CONFIG_LOGITECH_FF=y
    CONFIG_LOGO_LINUX_CLUT224=y
    CONFIG_LOGO=y
    CONFIG_MAC_PARTITION=y
    CONFIG_MAGIC_SYSRQ=y
    CONFIG_MAX_RAW_DEVS=8192
    CONFIG_MCORE2=y
    CONFIG_MD_AUTODETECT=y
    CONFIG_MD_FAULTY=m
    CONFIG_MD_LINEAR=m
    CONFIG_MD_MULTIPATH=m
    CONFIG_MD_RAID0=m
    CONFIG_MD_RAID10=m
    CONFIG_MD_RAID1=m
    CONFIG_MD_RAID456=m
    CONFIG_MD_RAID5_RESHAPE=y
    CONFIG_MD=y
    CONFIG_MEDIA_TUNER=m
    CONFIG_MEDIA_TUNER_MT20XX=m
    CONFIG_MEDIA_TUNER_SIMPLE=m
    CONFIG_MEDIA_TUNER_TDA8290=m
    CONFIG_MEDIA_TUNER_TDA9887=m
    CONFIG_MEDIA_TUNER_TEA5761=m
    CONFIG_MEDIA_TUNER_TEA5767=m
    CONFIG_MEDIA_TUNER_XC2028=m
    CONFIG_MEDIA_TUNER_XC5000=m
    CONFIG_MICROCODE_INTEL=y
    CONFIG_MICROCODE_OLD_INTERFACE=y
    CONFIG_MICROCODE=y
    CONFIG_MINIX_SUBPARTITION=y
    CONFIG_MISC_DEVICES=y
    CONFIG_MMU=y
    CONFIG_MODULE_FORCE_LOAD=y
    CONFIG_MODULE_FORCE_UNLOAD=y
    CONFIG_MODULES=y
    CONFIG_MODULE_UNLOAD=y
    CONFIG_MOUSE_PS2_ALPS=y
    CONFIG_MOUSE_PS2_LIFEBOOK=y
    CONFIG_MOUSE_PS2_LOGIPS2PP=y
    CONFIG_MOUSE_PS2_SYNAPTICS=y
    CONFIG_MOUSE_PS2_TRACKPOINT=y
    CONFIG_MOUSE_PS2=y
    CONFIG_MOUSE_SERIAL=m
    CONFIG_MOUSE_VSXXXAA=m
    CONFIG_MSDOS_FS=m
    CONFIG_MSDOS_PARTITION=y
    CONFIG_MTD_ABSENT=m
    CONFIG_MTD_BLKDEVS=m
    CONFIG_MTD_BLOCK2MTD=m
    CONFIG_MTD_BLOCK=m
    CONFIG_MTD_BLOCK_RO=m
    CONFIG_MTD_CFI_AMDSTD=m
    CONFIG_MTD_CFI_I1=y
    CONFIG_MTD_CFI_I2=y
    CONFIG_MTD_CFI_INTELEXT=m
    CONFIG_MTD_CFI=m
    CONFIG_MTD_CFI_STAA=m
    CONFIG_MTD_CFI_UTIL=m
    CONFIG_MTD_CHAR=m
    CONFIG_MTD_CONCAT=m
    CONFIG_MTD_GEN_PROBE=m
    CONFIG_MTD_JEDECPROBE=m
    CONFIG_MTD=m
    CONFIG_MTD_MAP_BANK_WIDTH_1=y
    CONFIG_MTD_MAP_BANK_WIDTH_2=y
    CONFIG_MTD_MAP_BANK_WIDTH_4=y
    CONFIG_MTD_MTDRAM=m
    CONFIG_MTD_NAND_DISKONCHIP=m
    CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0
    CONFIG_MTD_NAND_ECC_SMC=y
    CONFIG_MTD_NAND_IDS=m
    CONFIG_MTD_NAND=m
    CONFIG_MTD_NAND_NANDSIM=m
    CONFIG_MTD_NETSC520=m
    CONFIG_MTD_PARTITIONS=y
    CONFIG_MTDRAM_ERASE_SIZE=128
    CONFIG_MTD_RAM=m
    CONFIG_MTDRAM_TOTAL_SIZE=4096
    CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
    CONFIG_MTD_REDBOOT_PARTS=m
    CONFIG_MTD_ROM=m
    CONFIG_MTD_SC520CDP=m
    CONFIG_MTD_SCB2_FLASH=m
    CONFIG_MTD_TS5500=m
    CONFIG_MTRR_SANITIZER_ENABLE_DEFAULT=0
    CONFIG_MTRR_SANITIZER_SPARE_REG_NR_DEFAULT=1
    CONFIG_MTRR_SANITIZER=y
    CONFIG_MTRR=y
    CONFIG_NAMESPACES=y
    CONFIG_NETDEV_1000=y
    CONFIG_NETDEVICES=y
    CONFIG_NET_DMA=y
    CONFIG_NET_KEY=m
    CONFIG_NETWORK_FILESYSTEMS=y
    CONFIG_NETWORK_SECMARK=y
    CONFIG_NET=y
    CONFIG_NEW_LEDS=y
    CONFIG_NFS_ACL_SUPPORT=m
    CONFIG_NFS_COMMON=y
    CONFIG_NFSD=m
    CONFIG_NFSD_V2_ACL=y
    CONFIG_NFSD_V3_ACL=y
    CONFIG_NFSD_V3=y
    CONFIG_NFSD_V4=y
    CONFIG_NFS_FS=m
    CONFIG_NFS_V3_ACL=y
    CONFIG_NFS_V3=y
    CONFIG_NFS_V4=y
    CONFIG_NFTL=m
    CONFIG_NFTL_RW=y
    CONFIG_NLS_ASCII=y
    CONFIG_NLS_CODEPAGE_437=y
    CONFIG_NLS_DEFAULT="utf8"
    CONFIG_NLS_UTF8=y
    CONFIG_NLS=y
    CONFIG_NR_CPUS=16
    CONFIG_NSC_GPIO=m
    CONFIG_NVRAM=y
    CONFIG_OSF_PARTITION=y
    CONFIG_PACKET_MMAP=y
    CONFIG_PACKET=y
    CONFIG_PAGEFLAGS_EXTENDED=y
    CONFIG_PARTITION_ADVANCED=y
    CONFIG_PATA_SCH=m
    CONFIG_PC8736x_GPIO=m
    CONFIG_PCI_DIRECT=y
    CONFIG_PCI_DOMAINS=y
    CONFIG_PCIEPORTBUS=y
    CONFIG_PCI_MMCONFIG=y
    CONFIG_PCI_MSI=y
    CONFIG_PCI_QUIRKS=y
    CONFIG_PCI=y
    CONFIG_PCSPKR_PLATFORM=y
    CONFIG_PHYS_ADDR_T_64BIT=y
    CONFIG_PHYSICAL_ALIGN=0x200000
    CONFIG_PHYSICAL_START=0x200000
    CONFIG_PLIST=y
    CONFIG_PM=y
    CONFIG_PNPACPI=y
    CONFIG_PNP_DEBUG_MESSAGES=y
    CONFIG_PNP=y
    CONFIG_POSIX_MQUEUE=y
    CONFIG_POWER_SUPPLY=y
    CONFIG_PREEMPT_NONE=y
    CONFIG_PREVENT_FIRMWARE_BUILD=y
    CONFIG_PRINTK=y
    CONFIG_PRINT_QUOTA_WARNING=y
    CONFIG_PROC_EVENTS=y
    CONFIG_PROC_FS=y
    CONFIG_PROC_KCORE=y
    CONFIG_PROC_PAGE_MONITOR=y
    CONFIG_PROC_SYSCTL=y
    CONFIG_QFMT_V2=y
    CONFIG_QUOTACTL=y
    CONFIG_QUOTA=y
    CONFIG_RAID_ATTRS=y
    CONFIG_RAW_DRIVER=y
    CONFIG_REED_SOLOMON_DEC16=y
    CONFIG_REED_SOLOMON=m
    CONFIG_RELAY=y
    CONFIG_RESOURCES_64BIT=y
    CONFIG_RFD_FTL=m
    CONFIG_RFKILL_LEDS=y
    CONFIG_RFKILL=m
    CONFIG_RPCSEC_GSS_KRB5=m
    CONFIG_RPCSEC_GSS_SPKM3=m
    CONFIG_RTC_CLASS=y
    CONFIG_RTC_DRV_CMOS=y
    CONFIG_RTC_HCTOSYS_DEVICE="rtc"
    CONFIG_RTC_HCTOSYS=y
    CONFIG_RTC_INTF_DEV=y
    CONFIG_RTC_LIB=y
    CONFIG_RT_MUTEXES=y
    CONFIG_RWSEM_GENERIC_SPINLOCK=y
    CONFIG_SATA_AHCI=y
    CONFIG_SATA_PMP=y
    CONFIG_SCHED_HRTICK=y
    CONFIG_SCHED_MC=y
    CONFIG_SCSI_AACRAID=m
    CONFIG_SCSI_CONSTANTS=y
    CONFIG_SCSI_DMA=y
    CONFIG_SCSI_FC_ATTRS=m
    CONFIG_SCSI_ISCSI_ATTRS=m
    CONFIG_SCSI_LOGGING=y
    CONFIG_SCSI_LOWLEVEL=y
    CONFIG_SCSI_MULTI_LUN=y
    CONFIG_SCSI_NETLINK=y
    CONFIG_SCSI_PROC_FS=y
    CONFIG_SCSI_SPI_ATTRS=m
    CONFIG_SCSI_WAIT_SCAN=m
    CONFIG_SCSI=y
    CONFIG_SCTP_HMAC_MD5=y
    CONFIG_SELECT_MEMORY_MODEL=y
    CONFIG_SENSORS_ADM1021=m
    CONFIG_SENSORS_ADM1025=m
    CONFIG_SENSORS_ADM1026=m
    CONFIG_SENSORS_ADM1031=m
    CONFIG_SENSORS_ADM9240=m
    CONFIG_SENSORS_DS1621=m
    CONFIG_SENSORS_EEPROM=y
    CONFIG_SENSORS_F71805F=m
    CONFIG_SENSORS_FSCHER=m
    CONFIG_SENSORS_FSCPOS=m
    CONFIG_SENSORS_GL518SM=m
    CONFIG_SENSORS_GL520SM=m
    CONFIG_SENSORS_HDAPS=m
    CONFIG_SENSORS_IT87=m
    CONFIG_SENSORS_LM63=m
    CONFIG_SENSORS_LM75=m
    CONFIG_SENSORS_LM77=m
    CONFIG_SENSORS_LM78=m
    CONFIG_SENSORS_LM80=m
    CONFIG_SENSORS_LM83=m
    CONFIG_SENSORS_LM85=m
    CONFIG_SENSORS_LM87=m
    CONFIG_SENSORS_LM90=m
    CONFIG_SENSORS_LM92=m
    CONFIG_SENSORS_MAX1619=m
    CONFIG_SENSORS_PC87360=m
    CONFIG_SENSORS_SIS5595=m
    CONFIG_SENSORS_SMSC47B397=m
    CONFIG_SENSORS_SMSC47M192=m
    CONFIG_SENSORS_SMSC47M1=m
    CONFIG_SENSORS_VIA686A=m
    CONFIG_SENSORS_VT8231=m
    CONFIG_SENSORS_W83627EHF=m
    CONFIG_SENSORS_W83627HF=m
    CONFIG_SENSORS_W83781D=m
    CONFIG_SENSORS_W83791D=m
    CONFIG_SENSORS_W83792D=m
    CONFIG_SENSORS_W83L785TS=m
    CONFIG_SERIAL_8250_CONSOLE=y
    CONFIG_SERIAL_8250_DETECT_IRQ=y
    CONFIG_SERIAL_8250_EXTENDED=y
    CONFIG_SERIAL_8250_MANY_PORTS=y
    CONFIG_SERIAL_8250_NR_UARTS=32
    CONFIG_SERIAL_8250_PCI=y
    CONFIG_SERIAL_8250_PNP=y
    CONFIG_SERIAL_8250_RSA=y
    CONFIG_SERIAL_8250_RUNTIME_UARTS=4
    CONFIG_SERIAL_8250_SHARE_IRQ=y
    CONFIG_SERIAL_8250=y
    CONFIG_SERIAL_CORE_CONSOLE=y
    CONFIG_SERIAL_CORE=y
    CONFIG_SERIAL_JSM=m
    CONFIG_SERIO_I8042=y
    CONFIG_SERIO_LIBPS2=y
    CONFIG_SERIO_RAW=m
    CONFIG_SERIO_SERPORT=y
    CONFIG_SERIO=y
    CONFIG_SGI_PARTITION=y
    CONFIG_SHMEM=y
    CONFIG_SIGNALFD=y
    CONFIG_SLABINFO=y
    CONFIG_SLAB=y
    CONFIG_SMP=y
    CONFIG_SOLARIS_X86_PARTITION=y
    CONFIG_SPARSEMEM_EXTREME=y
    CONFIG_SPARSEMEM_MANUAL=y
    CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
    CONFIG_SPARSEMEM_VMEMMAP=y
    CONFIG_SPARSEMEM=y
    CONFIG_SPI_MASTER=y
    CONFIG_SPI=y
    CONFIG_SPLIT_PTLOCK_CPUS=4
    CONFIG_SSB_POSSIBLE=y
    CONFIG_STACKTRACE_SUPPORT=y
    CONFIG_STANDALONE=y
    CONFIG_STOP_MACHINE=y
    CONFIG_SUN_PARTITION=y
    CONFIG_SUNRPC_GSS=m
    CONFIG_SUNRPC=m
    CONFIG_SWAP=y
    CONFIG_SWIOTLB=y
    CONFIG_SYN_COOKIES=y
    CONFIG_SYSCTL_SYSCALL=y
    CONFIG_SYSCTL=y
    CONFIG_SYSFS_DEPRECATED_V2=y
    CONFIG_SYSFS_DEPRECATED=y
    CONFIG_SYSFS=y
    CONFIG_SYSVIPC_COMPAT=y
    CONFIG_SYSVIPC_SYSCTL=y
    CONFIG_SYSVIPC=y
    CONFIG_TCP_CONG_CUBIC=y
    CONFIG_THERMAL=y
    CONFIG_THRUSTMASTER_FF=y
    CONFIG_TICK_ONESHOT=y
    CONFIG_TIMERFD=y
    CONFIG_TMPFS=y
    CONFIG_TRACE_IRQFLAGS_SUPPORT=y
    CONFIG_UDF_FS=m
    CONFIG_UDF_NLS=y
    CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
    CONFIG_UID16=y
    CONFIG_UIO=y
    CONFIG_UNEVICTABLE_LRU=y
    CONFIG_UNIX98_PTYS=y
    CONFIG_UNIXWARE_DISKLABEL=y
    CONFIG_UNIX=y
    CONFIG_UNUSED_SYMBOLS=y
    CONFIG_USB_ARCH_HAS_EHCI=y
    CONFIG_USB_ARCH_HAS_HCD=y
    CONFIG_USB_ARCH_HAS_OHCI=y
    CONFIG_USB_DEVICE_CLASS=y
    CONFIG_USB_DEVICEFS=y
    CONFIG_USB_EHCI_HCD=y
    CONFIG_USB_EHCI_ROOT_HUB_TT=y
    CONFIG_USB_EHCI_TT_NEWSCHED=y
    CONFIG_USB_HIDDEV=y
    CONFIG_USB_HID=y
    CONFIG_USB_MON=y
    CONFIG_USB_STORAGE_ALAUDA=y
    CONFIG_USB_STORAGE_DATAFAB=y
    CONFIG_USB_STORAGE_DPCM=y
    CONFIG_USB_STORAGE_FREECOM=y
    CONFIG_USB_STORAGE_ISD200=y
    CONFIG_USB_STORAGE_JUMPSHOT=y
    CONFIG_USB_STORAGE_SDDR09=y
    CONFIG_USB_STORAGE_SDDR55=y
    CONFIG_USB_STORAGE_USBAT=y
    CONFIG_USB_STORAGE=y
    CONFIG_USB_SUPPORT=y
    CONFIG_USB_UHCI_HCD=y
    CONFIG_USB=y
    CONFIG_USE_GENERIC_SMP_HELPERS=y
    CONFIG_UTS_NS=y
    CONFIG_VFAT_FS=m
    CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=256
    CONFIG_VGACON_SOFT_SCROLLBACK=y
    CONFIG_VGA_CONSOLE=y
    CONFIG_VIDEO_ALLOW_V4L1=y
    CONFIG_VIDEO_DEV=m
    CONFIG_VIDEO_MEDIA=m
    CONFIG_VIDEO_V4L1_COMPAT=y
    CONFIG_VIDEO_V4L1=m
    CONFIG_VIDEO_V4L2_COMMON=m
    CONFIG_VIDEO_V4L2=m
    CONFIG_VIRT_TO_BUS=y
    CONFIG_VM_EVENT_COUNTERS=y
    CONFIG_VT_CONSOLE=y
    CONFIG_VT_HW_CONSOLE_BINDING=y
    CONFIG_VT=y
    CONFIG_VXFS_FS=m
    CONFIG_X86_64_SMP=y
    CONFIG_X86_64=y
    CONFIG_X86_BIOS_REBOOT=y
    CONFIG_X86_CMOV=y
    CONFIG_X86_CMPXCHG64=y
    CONFIG_X86_CMPXCHG=y
    CONFIG_X86_CPUID=y
    CONFIG_X86_CPU=y
    CONFIG_X86_DEBUGCTLMSR=y
    CONFIG_X86_HT=y
    CONFIG_X86_INTEL_USERCOPY=y
    CONFIG_X86_INTERNODE_CACHE_BYTES=64
    CONFIG_X86_IO_APIC=y
    CONFIG_X86_L1_CACHE_BYTES=64
    CONFIG_X86_L1_CACHE_SHIFT=6
    CONFIG_X86_LOCAL_APIC=y
    CONFIG_X86_MCE_INTEL=y
    CONFIG_X86_MCE=y
    CONFIG_X86_MINIMUM_CPU_FAMILY=64
    CONFIG_X86_MSR=y
    CONFIG_X86_P6_NOP=y
    CONFIG_X86_PAT=y
    CONFIG_X86_PC=y
    CONFIG_X86_PM_TIMER=y
    CONFIG_X86_RESERVE_LOW_64K=y
    CONFIG_X86_SMP=y
    CONFIG_X86_TRAMPOLINE=y
    CONFIG_X86_TSC=y
    CONFIG_X86_USE_PPRO_CHECKSUM=y
    CONFIG_X86_VERBOSE_BOOTUP=y
    CONFIG_X86_WP_WORKS_OK=y
    CONFIG_X86=y
    CONFIG_XFRM_USER=y
    CONFIG_XFRM=y
    CONFIG_XFS_FS=y
    CONFIG_XOR_BLOCKS=m
    CONFIG_ZISOFS=y
    CONFIG_ZLIB_DEFLATE=y
    CONFIG_ZLIB_INFLATE=y
    CONFIG_ZONE_DMA32=y
    CONFIG_ZONE_DMA_FLAG=1
    CONFIG_ZONE_DMA=y


    --
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2008-12-22 10:41    [W:0.268 / U:0.368 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site