lkml.org 
[lkml]   [2008]   [Dec]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH 13/27] drivers/net/ixgbe: fix sparse warnings: make symbols static
Date
From
Fix this sparse warnings:

drivers/net/ixgbe/ixgbe_82598.c:180:5: warning: symbol 'ixgbe_get_copper_link_capabilities_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:245:5: warning: symbol 'ixgbe_setup_fc_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:729:5: warning: symbol 'ixgbe_set_vmdq_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:773:5: warning: symbol 'ixgbe_set_vfta_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:897:5: warning: symbol 'ixgbe_read_analog_reg8_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:919:5: warning: symbol 'ixgbe_write_analog_reg8_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:940:5: warning: symbol 'ixgbe_read_i2c_eeprom_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:1000:5: warning: symbol 'ixgbe_get_supported_physical_layer_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_dcb_82598.c:100:5: warning: symbol 'ixgbe_dcb_config_packet_buffers_82598' was not declared. Should it be static?

Signed-off-by: Hannes Eder <hannes@hanneseder.net>
---
drivers/net/ixgbe/ixgbe_82598.c | 24 ++++++++++++------------
drivers/net/ixgbe/ixgbe_dcb_82598.c | 4 ++--
2 files changed, 14 insertions(+), 14 deletions(-)

diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c
index 7e09dab..ad5699d 100644
--- a/drivers/net/ixgbe/ixgbe_82598.c
+++ b/drivers/net/ixgbe/ixgbe_82598.c
@@ -177,9 +177,9 @@ static s32 ixgbe_get_link_capabilities_82598(struct ixgbe_hw *hw,
*
* Determines the link capabilities by reading the AUTOC register.
**/
-s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw,
- ixgbe_link_speed *speed,
- bool *autoneg)
+static s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg)
{
s32 status = IXGBE_ERR_LINK_SETUP;
u16 speed_ability;
@@ -242,7 +242,7 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
* Configures the flow control settings based on SW configuration. This
* function is used for 802.3x flow control configuration only.
**/
-s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
+static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
{
u32 frctl_reg;
u32 rmcs_reg;
@@ -726,7 +726,7 @@ static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
* @rar: receive address register index to associate with a VMDq index
* @vmdq: VMDq set index
**/
-s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
+static s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
{
u32 rar_high;

@@ -770,8 +770,8 @@ static s32 ixgbe_clear_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
*
* Turn on/off specified VLAN in the VLAN filter table.
**/
-s32 ixgbe_set_vfta_82598(struct ixgbe_hw *hw, u32 vlan, u32 vind,
- bool vlan_on)
+static s32 ixgbe_set_vfta_82598(struct ixgbe_hw *hw, u32 vlan, u32 vind,
+ bool vlan_on)
{
u32 regindex;
u32 bitindex;
@@ -894,7 +894,7 @@ static s32 ixgbe_blink_led_stop_82598(struct ixgbe_hw *hw, u32 index)
*
* Performs read operation to Atlas analog register specified.
**/
-s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
+static s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
{
u32 atlas_ctl;

@@ -916,7 +916,7 @@ s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
*
* Performs write operation to Atlas analog register specified.
**/
-s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
+static s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
{
u32 atlas_ctl;

@@ -937,8 +937,8 @@ s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
*
* Performs byte read operation to SFP module's EEPROM over I2C interface.
**/
-s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
- u8 *eeprom_data)
+static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
+ u8 *eeprom_data)
{
s32 status = 0;
u16 sfp_addr = 0;
@@ -997,7 +997,7 @@ out:
*
* Determines physical layer capabilities of the current configuration.
**/
-s32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
+static s32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
{
s32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;

diff --git a/drivers/net/ixgbe/ixgbe_dcb_82598.c b/drivers/net/ixgbe/ixgbe_dcb_82598.c
index fce6867..2c046b0 100644
--- a/drivers/net/ixgbe/ixgbe_dcb_82598.c
+++ b/drivers/net/ixgbe/ixgbe_dcb_82598.c
@@ -97,8 +97,8 @@ s32 ixgbe_dcb_get_pfc_stats_82598(struct ixgbe_hw *hw,
*
* Configure packet buffers for DCB mode.
*/
-s32 ixgbe_dcb_config_packet_buffers_82598(struct ixgbe_hw *hw,
- struct ixgbe_dcb_config *dcb_config)
+static s32 ixgbe_dcb_config_packet_buffers_82598(struct ixgbe_hw *hw,
+ struct ixgbe_dcb_config *dcb_config)
{
s32 ret_val = 0;
u32 value = IXGBE_RXPBSIZE_64KB;


\
 
 \ /
  Last update: 2008-12-22 20:25    [W:0.299 / U:0.324 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site