Messages in this thread | | | Date | Mon, 24 Nov 2008 14:27:44 +0100 | From | Willy Tarreau <> | Subject | Re: WARNING: at net/sched/sch_generic.c:219 dev_watchdog+0xfe/0x17e() with tg3 network |
| |
Hi Matt,
On Thu, Nov 20, 2008 at 01:53:18PM -0800, Matt Carlson wrote: > > Today, with the notebook connected to a gig switch, I could not reproduce > > the problem, even after one hour of approximately the same workload. I'll > > retry with the original 100 Mbps switch on monday.
fairly easier now with the same switch. I just have to transfer 100k objects over HTTP via this switch to see the problem happen :
tg3: eth0: The system may be re-ordering memory-mapped I/O cycles to the network device, attempting to recover. Please report the problem to the driver maintainer and include system chipset information. tg3: tg3_stop_block timed out, ofs=1400 enable_bit=2 tg3: tg3_stop_block timed out, ofs=c00 enable_bit=2 tg3: eth0: Link is down. tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX.
The switch is an el-cheapo D-Link 10/100. Note that this time I did not see any warning. Maybe I did not wait long enough though. Here are some stats and information I could collect :
root@wtap:/# ethtool -i eth0 driver: tg3 version: 3.94 firmware-version: 5705-v3.14 bus-info: 0000:02:0e.0
root@wtap:/# ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) Link detected: yes
root@wtap:/# ethtool -k eth0 Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: off
root@wtap:/# ethtool -a eth0 Pause parameters for eth0: Autonegotiate: on RX: on TX: on
root@wtap:/# netstat -ni Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth0 1500 0 61665 0 0 0 65133 0 0 0 BMRU lo 16436 0 945938 0 0 0 945938 0 0 0 LRU
root@wtap:/# ethtool -S eth0 NIC statistics: rx_octets: 52461785 rx_fragments: 0 rx_ucast_packets: 61018 rx_mcast_packets: 0 rx_bcast_packets: 476 rx_fcs_errors: 0 rx_align_errors: 0 rx_xon_pause_rcvd: 0 rx_xoff_pause_rcvd: 0 rx_mac_ctrl_rcvd: 0 rx_xoff_entered: 0 rx_frame_too_long_errors: 0 rx_jabbers: 0 rx_undersize_packets: 0 rx_in_length_errors: 0 rx_out_length_errors: 0 rx_64_or_less_octet_packets: 0 rx_65_to_127_octet_packets: 0 rx_128_to_255_octet_packets: 0 rx_256_to_511_octet_packets: 0 rx_512_to_1023_octet_packets: 0 rx_1024_to_1522_octet_packets: 0 rx_1523_to_2047_octet_packets: 0 rx_2048_to_4095_octet_packets: 0 rx_4096_to_8191_octet_packets: 0 rx_8192_to_9022_octet_packets: 0 tx_octets: 54658258 tx_collisions: 0 tx_xon_sent: 0 tx_xoff_sent: 0 tx_flow_control: 0 tx_mac_errors: 0 tx_single_collisions: 0 tx_mult_collisions: 0 tx_deferred: 0 tx_excessive_collisions: 0 tx_late_collisions: 0 tx_collide_2times: 0 tx_collide_3times: 0 tx_collide_4times: 0 tx_collide_5times: 0 tx_collide_6times: 0 tx_collide_7times: 0 tx_collide_8times: 0 tx_collide_9times: 0 tx_collide_10times: 0 tx_collide_11times: 0 tx_collide_12times: 0 tx_collide_13times: 0 tx_collide_14times: 0 tx_collide_15times: 0 tx_ucast_packets: 65033 tx_mcast_packets: 0 tx_bcast_packets: 0 tx_carrier_sense_errors: 0 tx_discards: 0 tx_errors: 0 dma_writeq_full: 0 dma_write_prioq_full: 0 rxbds_empty: 0 rx_discards: 0 rx_errors: 0 rx_threshold_hit: 0 dma_readq_full: 0 dma_read_prioq_full: 0 tx_comp_queue_full: 0 ring_set_send_prod_index: 0 ring_status_update: 0 nic_irqs: 0 nic_avoided_irqs: 0 nic_tx_threshold_hit: 0
I will try to go back to older kernels then bisect tg3 changes. I cannot do this right now since I'm using my laptop for work ;-)
Regards, Willy
| |