lkml.org 
[lkml]   [2008]   [Nov]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 12/16] Blackfin SPI Driver: get dma working for SPI flashes
Date
On Monday 17 November 2008, Bryan Wu wrote:
> From: Mike Frysinger <vapier.adi@gmail.com>
>
> When using a BF533-STAMP here with a W25X10 SPI flash. It works fine when
> enable_dma is disabled, but doesn't work at all when turning DMA on.
> We get just 0xff bytes back when trying to read the device.
>
> If change the code around so that it programs the SPI first and then
> enables DMA, it seems to work a lot better ...
>
> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
> Signed-off-by: Bryan Wu <cooloney@kernel.org>

Acked-by: David Brownell <dbrownell@users.sourceforge.net>

... and I observe some MM patches from you related to bugs
identifying those chips; good to know I wasn't the only
one to trip over those regressions!


> ---
> drivers/spi/spi_bfin5xx.c | 26 ++++++++++++++++----------
> 1 files changed, 16 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
> index fba77c2..5cd4873 100644
> --- a/drivers/spi/spi_bfin5xx.c
> +++ b/drivers/spi/spi_bfin5xx.c
> @@ -760,11 +760,10 @@ static void pump_transfers(unsigned long data)
> if (!full_duplex && drv_data->cur_chip->enable_dma
> && drv_data->len > 6) {
>
> - unsigned long dma_start_addr;
> + unsigned long dma_start_addr, flags;
>
> disable_dma(drv_data->dma_channel);
> clear_dma_irqstat(drv_data->dma_channel);
> - bfin_spi_disable(drv_data);
>
> /* config dma channel */
> dev_dbg(&drv_data->pdev->dev, "doing dma transfer\n");
> @@ -795,8 +794,7 @@ static void pump_transfers(unsigned long data)
> enable_dma(drv_data->dma_channel);
>
> /* start SPI transfer */
> - write_CTRL(drv_data,
> - (cr | BIT_CTL_TIMOD_DMA_TX | BIT_CTL_ENABLE));
> + write_CTRL(drv_data, cr | BIT_CTL_TIMOD_DMA_TX);
>
> /* just return here, there can only be one transfer
> * in this mode
> @@ -838,14 +836,22 @@ static void pump_transfers(unsigned long data)
> } else
> BUG();
>
> - /* start dma */
> - dma_enable_irq(drv_data->dma_channel);
> - set_dma_config(drv_data->dma_channel, dma_config);
> + /* oh man, here there be monsters ... and i dont mean the
> + * fluffy cute ones from pixar, i mean the kind that'll eat
> + * your data, kick your dog, and love it all. do *not* try
> + * and change these lines unless you (1) heavily test DMA
> + * with SPI flashes on a loaded system (e.g. ping floods),
> + * (2) know just how broken the DMA engine interaction with
> + * the SPI peripheral is, and (3) have someone else to blame
> + * when you screw it all up anyways.
> + */
> set_dma_start_addr(drv_data->dma_channel, dma_start_addr);
> + set_dma_config(drv_data->dma_channel, dma_config);
> + local_irq_save(flags);
> enable_dma(drv_data->dma_channel);
> -
> - /* start SPI transfer */
> - write_CTRL(drv_data, (cr | BIT_CTL_ENABLE));
> + write_CTRL(drv_data, cr);
> + dma_enable_irq(drv_data->dma_channel);
> + local_irq_restore(flags);
>
> } else {
> /* IO mode write then read */
> --
> 1.5.6.3
>
>




\
 
 \ /
  Last update: 2008-11-20 21:57    [W:0.125 / U:1.916 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site