Messages in this thread | | | Date | Tue, 28 Oct 2008 18:01:05 +0100 | From | Oskar Liljeblad <> | Subject | sata errors with Seagate 1.5TB on AMD 780G/SB700 motherboard |
| |
Can anyone make any sense of these SATA errors? They're killing my md RAID5 (at least the second error did).
Hard drives (ata1/sda, ata2/sdb, ata3/sdc): Seagate ST31500341AS 1.5TB SATA Motherboard: Asus M3A78-EH with AMD 780G/SB700 chipset SATA driver: ahci 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode]
Smart reports no errors on the drives, short & long tests have been run as well. The system is brand new.
I've read some reports about SATA 3.0 Gbps vs 1.5 Gbps problems and I'm considering limiting the drives to 1.5 Gbps using jumpers. Would that be a good idea?
19:24:26 ata2: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen 19:24:26 ata2: irq_stat 0x00400000, PHY RDY changed 19:24:26 ata2: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B } 19:24:26 ata2: hard resetting link 19:24:27 ata2: SATA link down (SStatus 0 SControl 300) 19:24:30 ata2: hard resetting link 19:24:35 ata2: link is slow to respond, please be patient (ready=0) 19:24:38 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) 19:24:38 ata2.00: configured for UDMA/133 19:24:38 ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4 19:24:38 ata2: irq_stat 0x00000040, connection status changed 19:24:38 ata2.00: configured for UDMA/133 19:24:38 ata2: EH complete
And then the day after:
09:07:49 ata3.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x6 frozen 09:07:49 ata3: SError: { HostInt } 09:07:49 ata3.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 09:07:49 res 40/00:00:00:00:00/00:00:00:00:00/a0 Emask 0x44 (timeout) 09:07:49 ata3.00: status: { DRDY } 09:07:49 ata3: hard resetting link 09:07:49 ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) 09:07:49 ata3.00: configured for UDMA/133 09:07:49 ata3: EH complete 09:07:49 sd 2:0:0:0: [sdc] 2930277168 512-byte hardware sectors (1500302 MB) 09:07:49 sd 2:0:0:0: [sdc] Write Protect is off 09:07:49 sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 09:07:49 sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 09:07:49 end_request: I/O error, dev sdc, sector 8 09:07:49 md: super_written gets error=-5, uptodate=0 09:07:49 raid5: Disk failure on sdc, disabling device. 09:07:49 raid5: Operation continuing on 1 devices.
For reference:
ata1: SATA max UDMA/133 abar m1024@0xf8fff800 port 0xf8fff900 irq 22 ata2: SATA max UDMA/133 abar m1024@0xf8fff800 port 0xf8fff980 irq 22 ata3: SATA max UDMA/133 abar m1024@0xf8fff800 port 0xf8fffa00 irq 22 ata4: SATA max UDMA/133 abar m1024@0xf8fff800 port 0xf8fffa80 irq 22 ata5: SATA max UDMA/133 abar m1024@0xf8fff800 port 0xf8fffb00 irq 22 ata6: SATA max UDMA/133 abar m1024@0xf8fff800 port 0xf8fffb80 irq 22 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: HPA detected: current 2930277168, native 18446744072344861488 ata1.00: ATA-8: ST31500341AS, SD17, max UDMA/133 ata1.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: HPA detected: current 2930277168, native 18446744072344861488 ata2.00: ATA-8: ST31500341AS, SD17, max UDMA/133 ata2.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: HPA detected: current 2930277168, native 18446744072344861488 ata3.00: ATA-8: ST31500341AS, SD17, max UDMA/133 ata3.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133
Regards,
Oskar
| |