lkml.org 
[lkml]   [2008]   [Jan]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [BUG] 2.6.24-git usb reset problems
From
Date
On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > On Tue, Jan 29 2008, Oliver Neukum wrote:
> > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <jens.axboe@oracle.com> wrote:
> > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > >> Greg KH wrote:
> > > >
> > > > > > > No difference, still just a lot of resets.
> > > > > > >
> > > > > > Where you able to figure out which usb storage transport is used?
> > > > > >
> > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > > > > pinpoint better where to look. Let me research a bit.
> > > > >
> > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > > > transport is 'Bulk'
> > > >
> > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > > > That should tell the reason for the resets.
> > >
> > > Sure, I'll do that. Will post the results tonight.
> >
> > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> > in the device, waited 10 seconds or so and pulled it out. These are the
> > messages.
> >
> > It all looks good until the MODE_SENSE command, where it only transfers
> > 4 of 192 bytes.
>
> No, that's not the problem. This is the problem:
>
> > usb-storage: *** thread awakened.
> > usb-storage: Command TEST_UNIT_READY (6 bytes)
> > usb-storage: 00 00 00 00 00 00
> > usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > usb-storage: Status code 0; transferred 31/31
> > usb-storage: -- transfer complete
> > usb-storage: Bulk command transfer result=0
> > usb-storage: Attempting to get CSW...
> > usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> > usb-storage: Status code 0; transferred 13/13
> > usb-storage: -- transfer complete
> > usb-storage: Bulk status result = 0
> > usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> > usb-storage: -- transport indicates command failure
> > usb-storage: Issuing auto-REQUEST_SENSE
> > usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > usb-storage: Status code 0; transferred 31/31
> > usb-storage: -- transfer complete
> > usb-storage: Bulk command transfer result=0
> > usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> > usb-storage: usb_sg_init returned -22
> > usb-storage: Bulk data transfer result 0x4
> > usb-storage: -- auto-sense failure
> > usb-storage: storage_pre_reset
> > ehci_hcd 0000:00:1d.7: port 1 high speed
> > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > ehci_hcd 0000:00:1d.7: port 1 high speed
> > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > usb-storage: storage_post_reset
> > usb-storage: usb_reset_composite_device returns 0
> > usb-storage: scsi cmd done, result=0x70000
> > usb-storage: *** thread sleeping.
>
> For some reason, usb_sg_init is boned during auto-sense.

OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
code ... that was also an update in 2.6.24

James




\
 
 \ /
  Last update: 2008-01-29 20:35    [from the cache]
©2003-2014 Jasper Spaans. hosted at Digital Ocean