lkml.org 
[lkml]   [2008]   [Jan]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH][RFC] fast file mapping for loop
On Thu, Jan 10 2008, Peter Zijlstra wrote:
>
> On Thu, 2008-01-10 at 10:49 +0100, Jens Axboe wrote:
> > On Thu, Jan 10 2008, Peter Zijlstra wrote:
> > >
> > > On Thu, 2008-01-10 at 08:37 +0000, Christoph Hellwig wrote:
> > >
> > > > Peter, any chance you could chime in here?
> > >
> > > I have this patch to add swap_out/_in methods. I expect we can loosen
> > > the requirement for swapcache pages and change the name a little.
> > >
> > > previously posted here:
> > > http://lkml.org/lkml/2007/5/4/143
> > >
> > > ---
> > > Subject: mm: add support for non block device backed swap files
> > >
> > > New addres_space_operations methods are added:
> > > int swapfile(struct address_space *, int);
> > > int swap_out(struct file *, struct page *, struct writeback_control *);
> > > int swap_in(struct file *, struct page *);
> > >
> > > When during sys_swapon() the swapfile() method is found and returns no error
> > > the swapper_space.a_ops will proxy to sis->swap_file->f_mapping->a_ops, and
> > > make use of swap_{out,in}() to write/read swapcache pages.
> > >
> > > The swapfile method will be used to communicate to the address_space that the
> > > VM relies on it, and the address_space should take adequate measures (like
> > > reserving memory for mempools or the like).
> > >
> > > This new interface can be used to obviate the need for ->bmap in the swapfile
> > > code. A filesystem would need to load (and maybe even allocate) the full block
> > > map for a file into memory and pin it there on ->swapfile(,1) so that
> > > ->swap_{out,in}() have instant access to it. It can be released on
> > > ->swapfile(,0).
> >
> > So this is where I don't think that's good enough, you cannot require a
> > full block/extent mapping of a file on setup. It can take quite some
> > time, a little testing I did here easily took 5 seconds for only a
> > couple of gigabytes. And that wasn't even worst case for that size. It
> > also wastes memory by populating extents that we may never read or
> > write.
> >
> > If you look at the loop addition I did, it populates lazily as needed
> > with some very simple logic to populate-ahead. In practice that performs
> > as well as a pre-populated map, the first IO to a given range will just
> > be a little slower since we have to bmap() it.
> >
> > Do you have plans to improve this area?
>
> Nope, for swap it _must_ be there, there is just no way we can do block
> allocation on swapout.

I appreciate that fact, just saying that we could have more flexibility
for other uses.

> That said, the swapfile() interface can be used to pre-populate the
> extend/block mapping, and when using swap_(in/out) without it, it can be
> done lazily.

I think the interface is too simple, I would much rather have a way to
dig into the file mappings and be allowed to request population and so
on. Without that, it can't be used for eg loop.

--
Jens Axboe



\
 
 \ /
  Last update: 2008-01-10 11:05    [W:0.053 / U:0.196 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site