Gaston, Jason D wrote:
>> -----Original Message-----
>> From: Gaston, Jason D
>> Sent: Friday, August 31, 2007 10:10 AM
>> To: 'Jeff Garzik'
>> Cc: linux-ide@vger.kernel.org; linux-kernel@vger.kernel.org
>> Subject: RE: [PATCH 2.6.23-rc4][reRESEND] ahci: RAID mode SATA patch
> for
>> Intel Tolapai
>>
>> This device has both AHCI and RAID modes that use the ahci driver.
> Only
>> the RAID mode DID's are being added as the PCI class code support will
>> cover the AHCI mode.  Looking at the Generic, PCI class code support
>> section, it uses "board_ahci".  I assumed that they should be the same
> as
>> the generic class code support is working on this platform.
>>
>> Thanks,
>>
>> Jason
>>
>>
>>> -----Original Message-----
>>> From: Jeff Garzik [mailto:jgarzik@pobox.com]
>>> Sent: Friday, August 31, 2007 12:47 AM
>>> To: Gaston, Jason D
>>> Cc: linux-ide@vger.kernel.org; linux-kernel@vger.kernel.org
>>> Subject: Re: [PATCH 2.6.23-rc4][reRESEND] ahci: RAID mode SATA patch
> for
>>> Intel Tolapai
>>>
>>> Jason Gaston wrote:
>>>> Resend trying to remove 8-bit characters in the email.
>>>>
>>>> This patch adds the Intel Tolapai RAID controller DID's for SATA
>> support.
>>>> Signed-off-by:  Jason Gaston <jason.d.gaston@intel.com>
>>>>
>>>> --- linux-2.6.23-rc4/drivers/ata/ahci.c.orig	2007-08-27
>>> 18:32:35.000000000 -0700
>>>> +++ linux-2.6.23-rc4/drivers/ata/ahci.c	2007-08-28
>> 16:58:11.000000000 -
>>> 0700
>>>> @@ -411,6 +411,8 @@
>>>>  	{ PCI_VDEVICE(INTEL, 0x292f), board_ahci_pi }, /* ICH9M */
>>>>  	{ PCI_VDEVICE(INTEL, 0x294d), board_ahci_pi }, /* ICH9 */
>>>>  	{ PCI_VDEVICE(INTEL, 0x294e), board_ahci_pi }, /* ICH9M */
>>>> +	{ PCI_VDEVICE(INTEL, 0x502a), board_ahci }, /* Tolapai */
>>>> +	{ PCI_VDEVICE(INTEL, 0x502b), board_ahci }, /* Tolapai */
>>> Why did you not use board_ahci_pi?  Is the AHCI ports-implemented
>>> register unreliable on this platform?
> 
> Jeff,
> 
> Do I need to change this to board_ahci_pi or is it ok to leave it at
> board_ahci, which will be used by the AHCI class code devices?

You are the one who needs to answer this question ;-)

Most new Intel AHCI have a sane and reliable Ports-Implemented register 
value even across reset, unlike earlier ones or some clones.  For those, 
we use board_ahci_pi.

If PI is not reliable across reset or if BIOS is absent (yes we care 
about that case, when we do our own PCI resume for example), then you 
should use board_ahci.

	Jeff



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/