lkml.org 
[lkml]   [2007]   [Sep]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH 3/4] Blackfin EMAC driver: Add phy abstraction layer supporting in bfin_emac driver
From
Date

- add MDIO functions and register mdio bus
- add phy abstraction layer (PAL) functions and use PAL API
- test on STAMP537 board

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
---
drivers/net/bfin_mac.c | 311 +++++++++++++++++++++++++++++-------------------
drivers/net/bfin_mac.h | 53 ++-------
2 files changed, 196 insertions(+), 168 deletions(-)

diff --git a/drivers/net/bfin_mac.c b/drivers/net/bfin_mac.c
index 5cb4433..53fe7de 100644
--- a/drivers/net/bfin_mac.c
+++ b/drivers/net/bfin_mac.c
@@ -47,6 +47,7 @@
#include <linux/spinlock.h>
#include <linux/ethtool.h>
#include <linux/mii.h>
+#include <linux/phy.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
@@ -94,6 +95,9 @@ static struct net_dma_desc_tx *current_tx_ptr;
static struct net_dma_desc_tx *tx_desc;
static struct net_dma_desc_rx *rx_desc;

+static void bf537mac_disable(void);
+static void bf537mac_enable(void);
+
static void desc_list_free(void)
{
struct net_dma_desc_rx *r;
@@ -282,8 +286,11 @@ static int setup_pin_mux(int action)
return 0;
}

+/*
+ * MII operations
+ */
/* Wait until the previous MDC/MDIO transaction has completed */
-static void poll_mdc_done(void)
+static void mdio_poll(void)
{
int timeout_cnt = MAX_TIMEOUT_CNT;

@@ -299,154 +306,201 @@ static void poll_mdc_done(void)
}

/* Read an off-chip register in a PHY through the MDC/MDIO port */
-static u16 read_phy_reg(u16 PHYAddr, u16 RegAddr)
+static int mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
{
- poll_mdc_done();
+ mdio_poll();
+
/* read mode */
- bfin_write_EMAC_STAADD(SET_PHYAD(PHYAddr) |
- SET_REGAD(RegAddr) |
+ bfin_write_EMAC_STAADD(SET_PHYAD((u16) phy_addr) |
+ SET_REGAD((u16) regnum) |
STABUSY);
- poll_mdc_done();

- return (u16) bfin_read_EMAC_STADAT();
+ mdio_poll();
+
+ return (int) bfin_read_EMAC_STADAT();
}

/* Write an off-chip register in a PHY through the MDC/MDIO port */
-static void raw_write_phy_reg(u16 PHYAddr, u16 RegAddr, u32 Data)
+static int mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
+ u16 value)
{
- bfin_write_EMAC_STADAT(Data);
+ mdio_poll();
+
+ bfin_write_EMAC_STADAT((u32) value);

/* write mode */
- bfin_write_EMAC_STAADD(SET_PHYAD(PHYAddr) |
- SET_REGAD(RegAddr) |
+ bfin_write_EMAC_STAADD(SET_PHYAD((u16) phy_addr) |
+ SET_REGAD((u16) regnum) |
STAOP |
STABUSY);

- poll_mdc_done();
+ mdio_poll();
+
+ return 0;
}

-static void write_phy_reg(u16 PHYAddr, u16 RegAddr, u32 Data)
+static int mdiobus_reset(struct mii_bus *bus)
{
- poll_mdc_done();
- raw_write_phy_reg(PHYAddr, RegAddr, Data);
+ return 0;
}

-/* set up the phy */
-static void bf537mac_setphy(struct net_device *dev)
+static void bf537_adjust_link(struct net_device *dev)
{
- u16 phydat;
struct bf537mac_local *lp = netdev_priv(dev);
+ struct phy_device *phydev = lp->phydev;
+ unsigned long flags;
+ int new_state = 0;
+
+ spin_lock_irqsave(&lp->lock, flags);
+ if (phydev->link) {
+ /* Now we make sure that we can be in full duplex mode.
+ * If not, we operate in half-duplex mode. */
+ if (phydev->duplex != lp->old_duplex) {
+ u32 opmode = bfin_read_EMAC_OPMODE();
+ new_state = 1;
+
+ if (phydev->duplex)
+ opmode |= FDMODE;
+ else
+ opmode &= ~(FDMODE);
+
+ bfin_write_EMAC_OPMODE(opmode);
+ lp->old_duplex = phydev->duplex;
+ }

- /* Program PHY registers */
- pr_debug("start setting up phy\n");
-
- /* issue a reset */
- raw_write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, 0x8000);
-
- /* wait half a second */
- msleep(500);
-
- phydat = read_phy_reg(lp->PhyAddr, PHYREG_MODECTL);
-
- /* advertise flow control supported */
- phydat = read_phy_reg(lp->PhyAddr, PHYREG_ANAR);
- phydat |= (1 << 10);
- write_phy_reg(lp->PhyAddr, PHYREG_ANAR, phydat);
+ if (phydev->speed != lp->old_speed) {
+#if defined(CONFIG_BFIN_MAC_RMII)
+ u32 opmode = bfin_read_EMAC_OPMODE();
+ bf537mac_disable();
+ switch (phydev->speed) {
+ case 10:
+ opmode |= RMII_10;
+ break;
+ case 100:
+ opmode &= ~(RMII_10);
+ break;
+ default:
+ printk(KERN_WARNING
+ "%s: Ack! Speed (%d) is not 10/100!\n",
+ DRV_NAME, phydev->speed);
+ break;
+ }
+ bfin_write_EMAC_OPMODE(opmode);
+ bf537mac_enable();
+#endif

- phydat = 0;
- if (lp->Negotiate)
- phydat |= 0x1000; /* enable auto negotiation */
- else {
- if (lp->FullDuplex)
- phydat |= (1 << 8); /* full duplex */
- else
- phydat &= (~(1 << 8)); /* half duplex */
+ new_state = 1;
+ lp->old_speed = phydev->speed;
+ }

- if (!lp->Port10)
- phydat |= (1 << 13); /* 100 Mbps */
- else
- phydat &= (~(1 << 13)); /* 10 Mbps */
+ if (!lp->old_link) {
+ new_state = 1;
+ lp->old_link = 1;
+ netif_schedule(dev);
+ }
+ } else if (lp->old_link) {
+ new_state = 1;
+ lp->old_link = 0;
+ lp->old_speed = 0;
+ lp->old_duplex = -1;
}

- if (lp->Loopback)
- phydat |= (1 << 14); /* enable TX->RX loopback */
-
- write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, phydat);
- msleep(500);
-
- phydat = read_phy_reg(lp->PhyAddr, PHYREG_MODECTL);
- /* check for SMSC PHY */
- if ((read_phy_reg(lp->PhyAddr, PHYREG_PHYID1) == 0x7) &&
- ((read_phy_reg(lp->PhyAddr, PHYREG_PHYID2) & 0xfff0) == 0xC0A0)) {
- /*
- * we have SMSC PHY so reqest interrupt
- * on link down condition
- */
-
- /* enable interrupts */
- write_phy_reg(lp->PhyAddr, 30, 0x0ff);
+ if (new_state) {
+ u32 opmode = bfin_read_EMAC_OPMODE();
+ phy_print_status(phydev);
+ pr_debug("EMAC_OPMODE = 0x%08x\n", opmode);
}
+
+ spin_unlock_irqrestore(&lp->lock, flags);
}

-/**************************************************************************/
-void setup_system_regs(struct net_device *dev)
+static int mii_probe(struct net_device *dev)
{
- int phyaddr;
- unsigned short sysctl, phydat;
- u32 opmode;
struct bf537mac_local *lp = netdev_priv(dev);
- int count = 0;
-
- phyaddr = lp->PhyAddr;
+ struct phy_device *phydev = NULL;
+ unsigned short sysctl;
+ int i;

- /* Enable PHY output */
+ /* Enable PHY output early */
if (!(bfin_read_VR_CTL() & PHYCLKOE))
bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE);

/* MDC = 2.5 MHz */
- sysctl = SET_MDCDIV(24);
- /* Odd word alignment for Receive Frame DMA word */
- /* Configure checksum support and rcve frame word alignment */
-#if defined(BFIN_MAC_CSUM_OFFLOAD)
- sysctl |= RXDWA | RXCKS;
-#else
- sysctl |= RXDWA;
-#endif
+ sysctl = bfin_read_EMAC_SYSCTL();
+ sysctl |= SET_MDCDIV(24);
bfin_write_EMAC_SYSCTL(sysctl);
- /* auto negotiation on */
- /* full duplex */
- /* 100 Mbps */
- phydat = PHY_ANEG_EN | PHY_DUPLEX | PHY_SPD_SET;
- write_phy_reg(phyaddr, PHYREG_MODECTL, phydat);

- /* test if full duplex supported */
- do {
- msleep(100);
- phydat = read_phy_reg(phyaddr, PHYREG_MODESTAT);
- if (count > 30) {
- printk(KERN_NOTICE DRV_NAME ": Link is down\n");
- printk(KERN_NOTICE DRV_NAME
- "please check your network connection\n");
- break;
- }
- count++;
- } while (!(phydat & 0x0004));
+ /* search for connect PHY device */
+ for (i = 0; i < PHY_MAX_ADDR; i++) {
+ struct phy_device *const tmp_phydev = lp->mii_bus.phy_map[i];

- phydat = read_phy_reg(phyaddr, PHYREG_ANLPAR);
+ if (!tmp_phydev)
+ continue; /* no PHY here... */

- if ((phydat & 0x0100) || (phydat & 0x0040)) {
- opmode = FDMODE;
- } else {
- opmode = 0;
- printk(KERN_INFO DRV_NAME
- ": Network is set to half duplex\n");
+ phydev = tmp_phydev;
+ break; /* found it */
+ }
+
+ /* now we are supposed to have a proper phydev, to attach to... */
+ if (!phydev) {
+ printk(KERN_INFO "%s: Don't found any phy device at all\n",
+ dev->name);
+ return -ENODEV;
}

#if defined(CONFIG_BFIN_MAC_RMII)
- opmode |= RMII; /* For Now only 100MBit are supported */
+ phydev = phy_connect(dev, phydev->dev.bus_id, &bf537_adjust_link, 0,
+ PHY_INTERFACE_MODE_RMII);
+#else
+ phydev = phy_connect(dev, phydev->dev.bus_id, &bf537_adjust_link, 0,
+ PHY_INTERFACE_MODE_MII);
#endif

- bfin_write_EMAC_OPMODE(opmode);
+ if (IS_ERR(phydev)) {
+ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
+ return PTR_ERR(phydev);
+ }
+
+ /* mask with MAC supported features */
+ phydev->supported &= (SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full
+ | SUPPORTED_Autoneg
+ | SUPPORTED_Pause | SUPPORTED_Asym_Pause
+ | SUPPORTED_MII
+ | SUPPORTED_TP);
+
+ phydev->advertising = phydev->supported;
+
+ lp->old_link = 0;
+ lp->old_speed = 0;
+ lp->old_duplex = -1;
+ lp->phydev = phydev;
+
+ printk(KERN_INFO "%s: attached PHY driver [%s] "
+ "(mii_bus:phy_addr=%s, irq=%d)\n",
+ DRV_NAME, phydev->drv->name, phydev->dev.bus_id, phydev->irq);
+
+ return 0;
+}
+
+/**************************************************************************/
+void setup_system_regs(struct net_device *dev)
+{
+ unsigned short sysctl;
+
+ /*
+ * Odd word alignment for Receive Frame DMA word
+ * Configure checksum support and rcve frame word alignment
+ */
+ sysctl = bfin_read_EMAC_SYSCTL();
+#if defined(BFIN_MAC_CSUM_OFFLOAD)
+ sysctl |= RXDWA | RXCKS;
+#else
+ sysctl |= RXDWA;
+#endif
+ bfin_write_EMAC_SYSCTL(sysctl);

bfin_write_EMAC_MMC_CTL(RSTC | CROLL);

@@ -686,18 +740,18 @@ static void bf537mac_disable(void)
/*
* Enable Interrupts, Receive, and Transmit
*/
-static int bf537mac_enable(struct net_device *dev)
+static void bf537mac_enable(void)
{
u32 opmode;

- pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+ pr_debug("%s: %s\n", DRV_NAME, __FUNCTION__);

/* Set RX DMA */
bfin_write_DMA1_NEXT_DESC_PTR(&(rx_list_head->desc_a));
bfin_write_DMA1_CONFIG(rx_list_head->desc_a.config);

/* Wait MII done */
- poll_mdc_done();
+ mdio_poll();

/* We enable only RX here */
/* ASTP : Enable Automatic Pad Stripping
@@ -721,8 +775,6 @@ static int bf537mac_enable(struct net_device *dev)
#endif
/* Turn on the EMAC rx */
bfin_write_EMAC_OPMODE(opmode);
-
- return 0;
}

/* Our watchdog timed out. Called by the networking layer */
@@ -735,7 +787,7 @@ static void bf537mac_timeout(struct net_device *dev)
/* reset tx queue */
tx_list_tail = tx_list_head->next;

- bf537mac_enable(dev);
+ bf537mac_enable();

/* We can accept TX packets again */
dev->trans_start = jiffies;
@@ -789,6 +841,7 @@ static void bf537mac_shutdown(struct net_device *dev)
*/
static int bf537mac_open(struct net_device *dev)
{
+ struct bf537mac_local *lp = netdev_priv(dev);
int retval;
pr_debug("%s: %s\n", dev->name, __FUNCTION__);

@@ -808,10 +861,10 @@ static int bf537mac_open(struct net_device *dev)
if (retval)
return retval;

- bf537mac_setphy(dev);
+ phy_start(lp->phydev);
setup_system_regs(dev);
bf537mac_disable();
- bf537mac_enable(dev);
+ bf537mac_enable();

pr_debug("hardware init finished\n");
netif_start_queue(dev);
@@ -828,11 +881,14 @@ static int bf537mac_open(struct net_device *dev)
*/
static int bf537mac_close(struct net_device *dev)
{
+ struct bf537mac_local *lp = netdev_priv(dev);
pr_debug("%s: %s\n", dev->name, __FUNCTION__);

netif_stop_queue(dev);
netif_carrier_off(dev);

+ phy_stop(lp->phydev);
+
/* clear everything */
bf537mac_shutdown(dev);

@@ -846,6 +902,7 @@ static int __init bf537mac_probe(struct net_device *dev)
{
struct bf537mac_local *lp = netdev_priv(dev);
int retval;
+ int i;

/* Grab the MAC address in the MAC */
*(__le32 *) (&(dev->dev_addr[0])) = cpu_to_le32(bfin_read_EMAC_ADDRLO());
@@ -862,7 +919,6 @@ static int __init bf537mac_probe(struct net_device *dev)

/* set the GPIO pins to Ethernet mode */
retval = setup_pin_mux(1);
-
if (retval)
return retval;

@@ -880,6 +936,23 @@ static int __init bf537mac_probe(struct net_device *dev)

setup_mac_addr(dev->dev_addr);

+ /* MDIO bus initial */
+ lp->mii_bus.priv = dev;
+ lp->mii_bus.read = mdiobus_read;
+ lp->mii_bus.write = mdiobus_write;
+ lp->mii_bus.reset = mdiobus_reset;
+ lp->mii_bus.name = "bfin_mac_mdio";
+ lp->mii_bus.id = 0;
+ lp->mii_bus.irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
+ for (i = 0; i < PHY_MAX_ADDR; ++i)
+ lp->mii_bus.irq[i] = PHY_POLL;
+
+ mdiobus_register(&lp->mii_bus);
+
+ retval = mii_probe(dev);
+ if (retval)
+ return retval;
+
/* Fill in the fields of the device structure with ethernet values. */
ether_setup(dev);

@@ -893,13 +966,6 @@ static int __init bf537mac_probe(struct net_device *dev)
dev->poll_controller = bf537mac_poll;
#endif

- /* fill in some of the fields */
- lp->version = 1;
- lp->PhyAddr = 0x01;
- lp->CLKIN = 25;
- lp->FullDuplex = 0;
- lp->Negotiate = 1;
- lp->FlowControl = 0;
spin_lock_init(&lp->lock);

/* now, enable interrupts */
@@ -912,9 +978,6 @@ static int __init bf537mac_probe(struct net_device *dev)
return -EBUSY;
}

- /* Enable PHY output early */
- if (!(bfin_read_VR_CTL() & PHYCLKOE))
- bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE);

retval = register_netdev(dev);
if (retval == 0) {
diff --git a/drivers/net/bfin_mac.h b/drivers/net/bfin_mac.h
index b827246..3a107ad 100644
--- a/drivers/net/bfin_mac.h
+++ b/drivers/net/bfin_mac.h
@@ -31,32 +31,6 @@
* 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*/

-/*
- * PHY REGISTER NAMES
- */
-#define PHYREG_MODECTL 0x0000
-#define PHYREG_MODESTAT 0x0001
-#define PHYREG_PHYID1 0x0002
-#define PHYREG_PHYID2 0x0003
-#define PHYREG_ANAR 0x0004
-#define PHYREG_ANLPAR 0x0005
-#define PHYREG_ANER 0x0006
-#define PHYREG_NSR 0x0010
-#define PHYREG_LBREMR 0x0011
-#define PHYREG_REC 0x0012
-#define PHYREG_10CFG 0x0013
-#define PHYREG_PHY1_1 0x0014
-#define PHYREG_PHY1_2 0x0015
-#define PHYREG_PHY2 0x0016
-#define PHYREG_TW_1 0x0017
-#define PHYREG_TW_2 0x0018
-#define PHYREG_TEST 0x0019
-
-#define PHY_RESET 0x8000
-#define PHY_ANEG_EN 0x1000
-#define PHY_DUPLEX 0x0100
-#define PHY_SPD_SET 0x2000
-
#define BFIN_MAC_CSUM_OFFLOAD

struct dma_descriptor {
@@ -104,27 +78,18 @@ struct bf537mac_local {
* can find out semi-useless statistics of how well the card is
* performing
*/
- int version;
+ struct net_device_stats stats;

- int FlowEnabled; /* record if data flow is active */
- int EtherIntIVG; /* IVG for the ethernet interrupt */
- int RXIVG; /* IVG for the RX completion */
- int TXIVG; /* IVG for the TX completion */
- int PhyAddr; /* PHY address */
- int OpMode; /* set these bits n the OPMODE regs */
- int Port10; /* set port speed to 10 Mbit/s */
- int GenChksums; /* IP checksums to be calculated */
- int NoRcveLnth; /* dont insert recv length at start of buffer */
- int StripPads; /* remove trailing pad bytes */
- int FullDuplex; /* set full duplex mode */
- int Negotiate; /* enable auto negotiation */
- int Loopback; /* loopback at the PHY */
- int Cache; /* Buffers may be cached */
- int FlowControl; /* flow control active */
- int CLKIN; /* clock in value in MHZ */
- unsigned short IntMask; /* interrupt mask */
unsigned char Mac[6]; /* MAC address of the board */
spinlock_t lock;
+
+ /* MII and PHY stuffs */
+ int old_link; /* used by bf537_adjust_link */
+ int old_speed;
+ int old_duplex;
+
+ struct phy_device *phydev;
+ struct mii_bus mii_bus;
};

extern void get_bf537_ether_addr(char *addr);
--
1.5.2
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2007-09-19 17:47    [W:0.044 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site