lkml.org 
[lkml]   [2007]   [Jul]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: [PATCH] Remove process freezer from suspend to RAM pathway
    On Fri, 6 Jul 2007, Kyle Moffett wrote:

    > Except Linus already decreed (and I heartily agree) that hibernation
    > and suspend-to-RAM were fundamentally completely different operations
    > and therefore any attempts to share code were basically just making a
    > big muddy mess of things. Would a thread "Remove phase-of-the-moon
    > calculations from network-recv code" be relevant to lunar observation
    > just because the two had to do with the phases of the moon? No!

    For that matter, shutting down a CPU and hibernation are fundamentally
    different operations -- but they both use the freezer. Is that a big
    muddy mess? But never mind; I won't discuss hibernation.

    > > A) Decide what to do about remote wakeup requests.
    >
    > Why do we care? If the wakeup request arrives before we go to sleep,
    > we obviously aren't asleep and so can't wake up. If it arrives after
    > we go to sleep then it will wake us up. Anything that depends on a
    > wakeup arriving mid-sequence is 100% masochistic race condition.

    You don't understand my point. If a wakeup request arrives before the
    system goes to sleep, and it is serviced, then a device which ought to
    have been suspended will in fact be awake. This will (if the parent's
    driver is written correctly) cause the sleep transition to abort.

    Not that there's necessarily anything wrong with that. I just wanted
    to be sure you were aware of the potential problems.

    > > C) Prevent devices and drivers from being registered or
    > > unregistered; in particular decide what to do about hot-plug or hot-
    > > unplug events.
    >
    > (1b) Again, that's where the NO_BIND flag comes in. If its set then
    > any device probe events must sleep, otherwise they can go through.

    I didn't say "bind", I said "registered". Admittedly, they are rather
    similar.

    Still, there are difficulties. Let's say a driver has set the NO_BIND
    flag for one of its devices. A bind request comes in, and the driver
    puts it on a waitqueue. Note that the binding thread holds the device
    semaphore; this is always true when a driver's probe routine is called.

    Later on it comes time for the PM core to resume the device, which will
    start up the threads on the waitqueue. Before doing so it must acquire
    the device semaphore. Deadlock!

    > If any of those things screw up suspend-to-RAM then it is 100% the
    > drivers fault and no "process freezer" is going to fix it, end of
    > story.

    Why do you say that? A "process freezer" can prevent bind and
    registration calls from occurring, since these calls have to run in
    process context. Ergo a freezer _can_ fix some of these problems.

    > And "A" cannot be made reliable. At some point you shut off
    > interrupts right before going to sleep, and at that point any remote
    > wakeup event is just going to get dropped until you actually enter
    > sleep mode and the hardware takes over again. If you miss a wakeup
    > event then whatever sent it should just retry, just as with *every*
    > other kind of network packet.

    Who mentioned network packets? And who says a remote wakeup event will
    get dropped once interrupts are disabled? More likely it will set a
    bit somewhere that causes the system to wake up immediately after it
    has gone to sleep.

    > > So what happens if a new subdevice arrives at the wrong time? Do
    > > you block instead of binding it? While holding a mutex needed to
    > > suspend the parent device?
    >
    > That would be a driver bug. If you have asynchronous probing then
    > proper suspend handling includes being able to postpone driver probe
    > events until after resume.

    One of your conditions (embodied in the pseudocode you posted earlier)
    was that drivers should be told to prevent binding and registration
    before the child devices are suspended. Currently the PM core doesn't
    do anything like that. You can't blame the drivers for this lack.

    Of course it could be added. Or perhaps more easily, the drivers that
    support asynchronous probing could be notified when a suspend is about
    to start so they could begin blocking bindings/registrations then.

    > > What about drivers trying to bind to existing devices?
    >
    > While binding it will clearly be holding a mutex/spinlock on the
    > parent device,

    ("Parent device"? Do you mean the device being bound? If so then I
    agree. Or do you mean the device's parent? If so then your statement
    is not clear at all. There is special-case code in the driver core to
    make sure it is true for USB devices, and it looks ugly as can be.)

    > so the suspend process will wait for it. When binding
    > is done the suspend_device() code will take the device lock and tell
    > everything else to postpone further bind requests as above.

    My question referred to drivers trying to bind or unbind a device
    _after_ the device has been suspended. I suppose you'll say that's
    covered by the NO_BIND flag. But now we have the locking problem
    mentioned above: The thread trying to bind is holding a lock which is
    needed for resuming.

    > Most drivers have an implicit NO_BIND flag: The device's interrupts
    > are off and/or its in a low-power state.

    That won't cause binding to block or be postponed; it will cause it to
    fail. Not the same thing at all.

    > USB is already terribly
    > buggy with regards to suspend: If you hotplug a device during
    > suspend (like the touchpad in my powerbook powering down/up), then
    > the USB stack will basically hang that controller. The device is off
    > and the hotplug triggers interrupts and IO, *EVEN* *WITHOUT*
    > *USERSPACE*.

    As one of the people responsible for the USB power management
    implementation, I would appreciate more details about this. For
    example, a dmesg log with CONFIG_USB_DEBUG turned on together with a
    complete description of the actions you took to provoke the bug.

    (I wonder how much of this "buginess" is caused by the lack of the
    freezer in PPC.)

    > So if your driver doesn't already have a proper way of blocking IO
    > during suspend then it probably doesn't suspend 50% of the time
    > anyways. A bug which bites *every* *time* is easy to fix, one which
    > only bites when things hit a race condition is much harder.

    The USB drivers (at least, the ones with runtime PM support) rely on
    the freezer to block I/O during suspend. As far as I know, they do
    suspend properly, on systems where the freezer is used.

    > That responsibility has been there ever since suspend-to-RAM support
    > was added. Nobody ever denied that writing a proper driver wasn't
    > tricky. You have to simultaneously be able to handle handle hot-
    > unplug, IO errors, interrupts, IO requests, suspend-to-RAM, and
    > hibernation. If your driver mutual-exclusion is buggy then it
    > probably already bites you during hotplug or other similar
    > scenarios. Let's at least make the problems much more reproducible
    > so we can fix the drivers properly instead of continuing to kludge
    > around it for all eternity.

    Is reproducibility really a problem at this stage? A bug which bites
    50% of the time might not be quite as easy to fix as one which occurs
    every time, but it isn't terribly bad either.

    Alan Stern

    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2007-07-07 05:01    [W:4.058 / U:0.096 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site