Messages in this thread | | | From | Inguna <> | Subject | problem with huawei e630 data card | Date | Mon, 30 Jul 2007 21:58:39 +0300 |
| |
hello i use a kernel 2.6.22.1 (last stabile kernel from kernel.org) i have a huewei e630 hsdpa/umts/edge/gprs/gsm data card, who set in pcmcia slot on notebook ( acer 2413 travelmate, linux mandriva 2007. there is dmesg output:
pccard: CardBus card inserted into slot 0 yenta EnE: chaning testregister 0xC9, 04 -> 04 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:07:00.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 22 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:07:00.0 to 64 ohci_hcd 0000:07:00.0: OHCI Host Controller ohci_hcd 0000:07:00.0: new USB bus registered, assigned bus number 6 ohci_hcd 0000:07:00.0: irq 16, io mem 0x38000000 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 1 port detected PCI: Enabling device 0000:07:00.1 (0000 -> 0002) ACPI: PCI Interrupt 0000:07:00.1[B] -> GSI 22 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:07:00.1 to 64 ohci_hcd 0000:07:00.1: OHCI Host Controller ohci_hcd 0000:07:00.1: new USB bus registered, assigned bus number 7 ohci_hcd 0000:07:00.1: irq 16, io mem 0x38001000 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 1 port detected usb 6-1: new full speed USB device using ohci_hcd and address 2 usb 6-1: configuration #1 chosen from 1 choice usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 pl2303 6-1:1.0: pl2303 converter detected usb 6-1: pl2303 converter now attached to ttyUSB0 pl2303 6-1:1.1: pl2303 converter detected usb 6-1: pl2303 converter now attached to ttyUSB1 pl2303 6-1:1.2: pl2303 converter detected usb 6-1: pl2303 converter now attached to ttyUSB2 usbcore: registered new interface driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1 BUG: unable to handle kernel NULL pointer dereference at virtual address 0000001c printing eip: e05a58e6 *pde = 00000000 Oops: 0002 [#1] SMP Modules linked in: option pl2303 usbserial ohci_hcd nls_cp437 nls_iso8859_1 smbfs i915 drm snd_seq_dummy nfsd snd_seq_oss snd_seq_midi_event exportfs snd_seq lockd snd_seq_device nfs_acl sunrpc snd_pcm_oss snd_mixer_oss snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm snd_timer snd_page_alloc snd soundcore ipv6 8139too mii af_packet ide_cd loop nls_utf8 ntfs dm_mod video thermal processor fan container button battery ac pcmcia yenta_socket rsrc_nonstatic pcmcia_core intel_agp agpgart nvram ehci_hcd uhci_hcd usbcore evdev joydev tsdev CPU: 0 EIP: 0060:[<e05a58e6>] Not tainted VLI EFLAGS: 00010246 (2.6.22.1 #2) EIP is at pl2303_open+0x456/0x9e0 [pl2303] eax: 00000000 ebx: 00000000 ecx: 00000000 edx: c6493800 esi: c9606440 edi: ccba4800 ebp: cc2b7e70 esp: cc2b7e14 ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068 Process hald-probe-seri (pid: 22697, ti=cc2b6000 task=cc0ca560 task.ti=cc2b6000) Stack: 00000040 00000009 00000000 00000000 00000000 00000064 cc2b7e4c c0120b80 ceb1b3a0 00000000 00000003 00000000 c0921000 ca255e00 cc2b7e58 c025f24a 00000000 cc2b7e9c c025ff0f c9606440 ccba4800 c9606440 c0921000 cc2b7e9c Call Trace: [<c01050aa>] show_trace_log_lvl+0x1a/0x30 [<c0105171>] show_stack_log_lvl+0xb1/0xe0 [<c0105372>] show_registers+0x1d2/0x2e0 [<c0105594>] die+0x114/0x270 [<c011f09b>] do_page_fault+0x2cb/0x5d0 [<c033cdea>] error_code+0x72/0x78 [<e06952cc>] serial_open+0xfc/0x150 [usbserial] [<c0262f5b>] tty_open+0x14b/0x2e0 [<c017f653>] chrdev_open+0xa3/0x190 [<c017b2ab>] __dentry_open+0xab/0x1a0 [<c017b445>] nameidata_to_filp+0x35/0x40 [<c017b499>] do_filp_open+0x49/0x50 [<c017b4e7>] do_sys_open+0x47/0xd0 [<c017b5ac>] sys_open+0x1c/0x20 [<c0104086>] sysenter_past_esp+0x5f/0x85 ======================= Code: 1c 8b 47 44 ba d0 00 00 00 e8 f7 70 ab ff 85 c0 89 c3 0f 85 24 05 00 00 8b 0d 80 99 5a e0 85 c9 0f 85 37 04 00 00 8b 47 24 8b 16 <89> 50 1c 8b 47 24 ba d0 00 00 00 e8 ca 70 ab ff 89 c3 31 c0 85 EIP: [<e05a58e6>] pl2303_open+0x456/0x9e0 [pl2303] SS:ESP 0068:cc2b7e14 BUG: unable to handle kernel NULL pointer dereference at virtual address 0000001c printing eip: e05a58e6 *pde = 00000000 Oops: 0002 [#2] SMP Modules linked in: option pl2303 usbserial ohci_hcd nls_cp437 nls_iso8859_1 smbfs i915 drm snd_seq_dummy nfsd snd_seq_oss snd_seq_midi_event exportfs snd_seq lockd snd_seq_device nfs_acl sunrpc snd_pcm_oss snd_mixer_oss snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm snd_timer snd_page_alloc snd soundcore ipv6 8139too mii af_packet ide_cd loop nls_utf8 ntfs dm_mod video thermal processor fan container button battery ac pcmcia yenta_socket rsrc_nonstatic pcmcia_core intel_agp agpgart nvram ehci_hcd uhci_hcd usbcore evdev joydev tsdev CPU: 0 EIP: 0060:[<e05a58e6>] Not tainted VLI EFLAGS: 00010246 (2.6.22.1 #2) EIP is at pl2303_open+0x456/0x9e0 [pl2303] eax: 00000000 ebx: 00000000 ecx: 00000000 edx: c6493800 esi: c9606500 edi: c25f7a00 ebp: cc2e1e70 esp: cc2e1e14 ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068 Process hald-probe-seri (pid: 22733, ti=cc2e0000 task=cfdbfa90 task.ti=cc2e0000) Stack: 00000040 00000009 00000000 00000000 00000000 00000064 cc2e1e4c c0120b80 dcf2ba20 00000000 00000003 00000000 c0922000 ca255e00 cc2e1e58 c025f24a 00000000 cc2e1e9c c025ff0f c9606500 c25f7a00 c9606500 c0922000 cc2e1e9c Call Trace: [<c01050aa>] show_trace_log_lvl+0x1a/0x30 [<c0105171>] show_stack_log_lvl+0xb1/0xe0 [<c0105372>] show_registers+0x1d2/0x2e0 [<c0105594>] die+0x114/0x270 [<c011f09b>] do_page_fault+0x2cb/0x5d0 [<c033cdea>] error_code+0x72/0x78 [<e06952cc>] serial_open+0xfc/0x150 [usbserial] [<c0262f5b>] tty_open+0x14b/0x2e0 [<c017f653>] chrdev_open+0xa3/0x190 [<c017b2ab>] __dentry_open+0xab/0x1a0 [<c017b445>] nameidata_to_filp+0x35/0x40 [<c017b499>] do_filp_open+0x49/0x50 [<c017b4e7>] do_sys_open+0x47/0xd0 [<c017b5ac>] sys_open+0x1c/0x20 [<c0104086>] sysenter_past_esp+0x5f/0x85 ======================= Code: 1c 8b 47 44 ba d0 00 00 00 e8 f7 70 ab ff 85 c0 89 c3 0f 85 24 05 00 00 8b 0d 80 99 5a e0 85 c9 0f 85 37 04 00 00 8b 47 24 8b 16 <89> 50 1c 8b 47 24 ba d0 00 00 00 e8 ca 70 ab ff 89 c3 31 c0 85 EIP: [<e05a58e6>] pl2303_open+0x456/0x9e0 [pl2303] SS:ESP 0068:cc2e1e14
there is lsmod:
[root@localhost gazella]# lsmod Module Size Used by option 12544 0 pl2303 22916 2 usbserial 33256 6 option,pl2303 ohci_hcd 23172 0 nls_cp437 9728 3 nls_iso8859_1 8064 3 smbfs 61432 3 i915 25856 2 drm 75668 3 i915 snd_seq_dummy 6788 0 nfsd 213488 17 snd_seq_oss 33152 0 snd_seq_midi_event 10240 1 snd_seq_oss exportfs 8704 1 nfsd snd_seq 50256 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event lockd 63624 2 nfsd snd_seq_device 10636 3 snd_seq_dummy,snd_seq_oss,snd_seq nfs_acl 7040 1 nfsd sunrpc 151932 12 nfsd,lockd,nfs_acl snd_pcm_oss 42272 0 snd_mixer_oss 17920 1 snd_pcm_oss snd_intel8x0 32796 1 snd_ac97_codec 99620 1 snd_intel8x0 ac97_bus 6144 1 snd_ac97_codec snd_pcm 72068 3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec snd_timer 22660 2 snd_seq,snd_pcm snd_page_alloc 11656 2 snd_intel8x0,snd_pcm snd 48100 11 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer soundcore 9952 1 snd ipv6 249892 18 8139too 25728 0 mii 8704 1 8139too af_packet 24200 2 ide_cd 38688 1 loop 17412 0 nls_utf8 5888 3 ntfs 101568 1 dm_mod 51264 0 video 18440 0 thermal 14856 0 processor 29160 1 thermal fan 7684 0 container 7424 0 button 10128 0 battery 12292 0 ac 7940 0 pcmcia 36780 0 yenta_socket 26892 2 rsrc_nonstatic 14848 1 yenta_socket pcmcia_core 36756 3 pcmcia,yenta_socket,rsrc_nonstatic intel_agp 25364 1 agpgart 31048 3 drm,intel_agp nvram 11400 0 ehci_hcd 33548 0 uhci_hcd 25872 0 usbcore 121224 7 option,pl2303,usbserial,ohci_hcd,ehci_hcd,uhci_hcd evdev 11904 2 joydev 12352 0 tsdev 10560 0 [root@localhost gazella]#
there - lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) 00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) 00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03) 00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03) 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03) 06:05.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) 06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 06:09.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01) 07:00.0 USB Controller: NEC Corporation USB (rev 43) 07:00.1 USB Controller: NEC Corporation USB (rev 43)
i also a serrch in internet,and i found, this problem is http://lists.debian.org/debian-kernel/2007/06/msg00013.html i e a kernel 2.6.18 also have a this problem.
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |