lkml.org 
[lkml]   [2007]   [May]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    Subject2.6.20.4 / 2.6.21.1 AT91SAM9260-EK oops
    From


    I am having issues getting both a working kernel and rootfs going on an
    Atmel AT91SAM9260-EK board. I can boot the Atmel-provided 2.6.18-rc4 kernel
    and my rootfs image created with buildroot. But when I try to boot my own
    2.6.20.4 or 2.6.21.1 kernels, I get an oops as below. Forgive the
    formatting... Below that is my kernel config.

    Any ideas why the kernel might be dying trying to open and initialize a TTY?


    Thanks!

    Ryan




    Uncompressing
    Linux.............................................................
    ................... done, booting the kernel.
    Linux version 2.6.21.1-pml1 (rordway@alpha.powermand.com) (gcc version
    4.1.2) #2
    Thu May 3 13:47:43 PDT 2007
    CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
    Machine: Atmel AT91SAM9260-EK
    Memory policy: ECC disabled, Data cache writeback
    Clocks: CPU 198 MHz, master 99 MHz, main 18.432 MHz
    CPU0: D VIVT write-back cache
    CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
    CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
    Built 1 zonelists. Total pages: 16256
    Kernel command line: ram=64M console=ttyS0,115200 initrd=0x21000000
    root=/dev/ram0 init=/linuxrc rw
    AT91: 96 gpio irqs in 3 banks
    PID hash table entries: 256 (order: 8, 1024 bytes)
    Console: colour dummy device 80x30
    Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    Memory: 64MB = 64MB total
    Memory: 59312KB available (2224K code, 330K data, 104K init)
    Mount-cache hash table entries: 512
    CPU: Testing write buffer coherency: ok
    NET: Registered protocol family 16
    Generic PHY: Registered new driver
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    NET: Registered protocol family 2
    IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    TCP established hash table entries: 2048 (order: 3, 40960 bytes)
    TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
    TCP: Hash tables configured (established 2048 bind 2048)
    TCP reno registered
    checking if image is initramfs...it isn't (no cpio magic); looks like an
    initrd
    Freeing initrd memory: 2888K
    NetWinder Floating Point Emulator V0.97 (extended precision)
    JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
    io scheduler noop registered (default)
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
    loop: loaded (max 8 devices)
    Davicom DM9161E: Registered new driver
    Davicom DM9131: Registered new driver
    dm9000 Ethernet Driver
    macb macb: detected PHY at address 0 (ID 0181:b8a0)
    eth0: Atmel MACB at 0xfffc4000 irq 21 (02:03:04:05:06:07)
    NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
    SSFDC read-only Flash Translation layer
    NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V
    8-bi
    t)
    NAND bus width 16 instead 8 bit
    No NAND device found!!!
    at91_ohci at91_ohci: AT91 OHCI
    at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
    at91_ohci at91_ohci: irq 20, io mem 0x00500000
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    usbcore: registered new interface driver usbserial
    drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
    usbcore: registered new interface driver usbserial_generic
    drivers/usb/serial/usb-serial.c: USB Serial Driver core
    drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101
    usbcore: registered new interface driver cp2101
    drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor
    dri
    ver v0.07
    udc: at91_udc version 3 May 2006
    ether gadget: using random self ethernet address
    ether gadget: using random host ethernet address
    usb0: Ethernet Gadget, version: May Day 2005
    usb0: using at91_udc, OUT ep2 IN ep1 STATUS ep4
    usb0: MAC da:af:79:f3:97:1e
    usb0: HOST MAC ee:9f:94:c8:5d:22
    mice: PS/2 mouse device common for all mice
    AT91 MMC: 4 wire bus mode not supported by this driver - using 1 wire
    TCP cubic registered
    Initializing XFRM netlink socket
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    NET: Registered protocol family 15
    drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
    RAMDISK: Compressed image found at block 0
    VFS: Mounted root (ext2 filesystem).
    Freeing init memory: 104K
    Unable to handle kernel NULL pointer dereference at virtual address 00000000
    pgd = c0004000
    [00000000] *pgd=00000000
    Internal error: Oops: 5 [#1]
    Modules linked in:
    CPU: 0
    PC is at init_dev+0x28/0x4e8
    LR is at tty_open+0x120/0x304
    pc : [<c00f8a18>] lr : [<c00fbce4>] Not tainted
    sp : c12e1e08 ip : c12e1e50 fp : c12e1e4c
    r10: 00000002 r9 : 00000000 r8 : c12e0000
    r7 : 00000001 r6 : c1237c00 r5 : c0299c38 r4 : c12fb8a0
    r3 : 00000000 r2 : c12e1e54 r1 : 00000000 r0 : c1237c00
    Flags: nZCv IRQs on FIQs on Mode SVC_32 Segment kernel
    Control: 5317F
    Table: 20004000 DAC: 00000017
    Process swapper (pid: 1, stack limit = 0xc12e0258)
    Stack: (0xc12e1e08 to 0xc12e2000)
    1e00: c12e1e54 c025fce8 c12e1e50 c1237c00 00000000
    c12e0000
    1e20: c12e1e4c c12fb8a0 c0299c38 00500001 00000001 c12e0000 00000000
    00000002
    1e40: c12e1e7c c12e1e50 c00fbce4 c00f8a00 00000000 c3d78a40 00000000
    c0299c38
    1e60: c3d78a40 c12fb8a0 c1257bc8 00000000 c12e1ea4 c12e1e80 c0080d7c
    c00fbbd4
    1e80: c12e1ea4 00000000 c12fb8a0 c3d78a40 c0080c2c c12d3220 c12e1ecc
    c12e1ea8
    1ea0: c007c758 c0080c3c c12fb8a0 c12e1ef8 c03a4000 00000000 ffffff9c
    00000000
    1ec0: c12e1eec c12e1ed0 c007c8f4 c007c674 00000000 ffffff9c 00000000
    00000002
    1ee0: c12e1f5c c12e1ef0 c007c950 c007c8d0 c12e1ef8 c00ef830 c1257bc8
    c12d3220
    1f00: c0065970 00000002 c12e0000 00000101 00000001 00000000 c12e1f34
    c12e1f28
    1f20: c01d74f0 c00ef830 c12e1f5c c12e1f38 c007c658 c01d74f0 00000002
    00000003
    1f40: 00000000 c12fb8a0 00000002 00000000 c12e1f84 c12e1f60 c007c9ac
    c007c91c
    1f60: c0029be8 c0269f98 c001f87c c12e0000 00000000 00000000 c12e1f94
    c12e1f88
    1f80: c007ca28 c007c968 c12e1fac c12e1f98 c002205c c007ca14 c0269f98
    c0269f98
    1fa0: c12e1ff4 c12e1fb0 c000886c c002203c 00000000 00000000 c00086fc
    c00406bc
    1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    00000000
    1fe0: 00000000 00000000 00000000 c12e1ff8 c00406bc c000870c 00220008
    00020015
    Backtrace:
    [<c00f89f0>] (init_dev+0x0/0x4e8) from [<c00fbce4>] (tty_open+0x120/0x304)
    [<c00fbbc4>] (tty_open+0x0/0x304) from [<c0080d7c>]
    (chrdev_open+0x150/0x1a0)
    [<c0080c2c>] (chrdev_open+0x0/0x1a0) from [<c007c758>]
    (__dentry_open+0xf4/0x1e4)
    r7 = C12D3220 r6 = C0080C2C r5 = C3D78A40 r4 = C12FB8A0
    [<c007c664>] (__dentry_open+0x0/0x1e4) from [<c007c8f4>]
    (nameidata_to_filp+0x34/0x4c)
    [<c007c8c0>] (nameidata_to_filp+0x0/0x4c) from [<c007c950>]
    (do_filp_open+0x44/0x4c)
    r4 = 00000002
    [<c007c90c>] (do_filp_open+0x0/0x4c) from [<c007c9ac>]
    (do_sys_open+0x54/0x98)
    r5 = 00000000 r4 = 00000002
    [<c007c958>] (do_sys_open+0x0/0x98) from [<c007ca28>] (sys_open+0x24/0x28)
    r8 = 00000000 r7 = 00000000 r6 = C12E0000 r5 = C001F87C
    r4 = C0269F98
    [<c007ca04>] (sys_open+0x0/0x28) from [<c002205c>] (init_post+0x30/0xe8)
    [<c002202c>] (init_post+0x0/0xe8) from [<c000886c>] (init+0x170/0x1b8)
    r4 = C0269F98
    [<c00086fc>] (init+0x0/0x1b8) from [<c00406bc>] (do_exit+0x0/0x808)
    r7 = 00000000 r6 = 00000000 r5 = 00000000 r4 = 00000000
    Code: e3130010 059030c8 e1a06000 e1a09001 (07935101)
    Kernel panic - not syncing: Attempted to kill init!






    #
    # Automatically generated make config: don't edit
    # Linux kernel version: 2.6.20.4
    # Fri May 4 11:13:33 2007
    #
    CONFIG_ARM=y
    # CONFIG_GENERIC_TIME is not set
    CONFIG_MMU=y
    CONFIG_GENERIC_HARDIRQS=y
    CONFIG_TRACE_IRQFLAGS_SUPPORT=y
    CONFIG_HARDIRQS_SW_RESEND=y
    CONFIG_GENERIC_IRQ_PROBE=y
    CONFIG_RWSEM_GENERIC_SPINLOCK=y
    # CONFIG_ARCH_HAS_ILOG2_U32 is not set
    # CONFIG_ARCH_HAS_ILOG2_U64 is not set
    CONFIG_GENERIC_HWEIGHT=y
    CONFIG_GENERIC_CALIBRATE_DELAY=y
    CONFIG_VECTORS_BASE=0xffff0000
    CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

    #
    # Code maturity level options
    #
    CONFIG_EXPERIMENTAL=y
    CONFIG_BROKEN_ON_SMP=y
    CONFIG_INIT_ENV_ARG_LIMIT=32

    #
    # General setup
    #
    CONFIG_LOCALVERSION="-pml1"
    CONFIG_LOCALVERSION_AUTO=y
    # CONFIG_SWAP is not set
    CONFIG_SYSVIPC=y
    # CONFIG_IPC_NS is not set
    CONFIG_POSIX_MQUEUE=y
    # CONFIG_BSD_PROCESS_ACCT is not set
    # CONFIG_TASKSTATS is not set
    # CONFIG_UTS_NS is not set
    # CONFIG_AUDIT is not set
    CONFIG_IKCONFIG=y
    CONFIG_IKCONFIG_PROC=y
    CONFIG_SYSFS_DEPRECATED=y
    # CONFIG_RELAY is not set
    CONFIG_INITRAMFS_SOURCE=""
    CONFIG_CC_OPTIMIZE_FOR_SIZE=y
    CONFIG_SYSCTL=y
    # CONFIG_EMBEDDED is not set
    CONFIG_UID16=y
    CONFIG_SYSCTL_SYSCALL=y
    CONFIG_KALLSYMS=y
    # CONFIG_KALLSYMS_ALL is not set
    CONFIG_KALLSYMS_EXTRA_PASS=y
    CONFIG_HOTPLUG=y
    CONFIG_PRINTK=y
    CONFIG_BUG=y
    CONFIG_ELF_CORE=y
    CONFIG_BASE_FULL=y
    CONFIG_FUTEX=y
    CONFIG_EPOLL=y
    CONFIG_SHMEM=y
    CONFIG_SLAB=y
    CONFIG_VM_EVENT_COUNTERS=y
    CONFIG_RT_MUTEXES=y
    # CONFIG_TINY_SHMEM is not set
    CONFIG_BASE_SMALL=0
    # CONFIG_SLOB is not set

    #
    # Loadable module support
    #
    CONFIG_MODULES=y
    CONFIG_MODULE_UNLOAD=y
    # CONFIG_MODULE_FORCE_UNLOAD is not set
    CONFIG_MODVERSIONS=y
    # CONFIG_MODULE_SRCVERSION_ALL is not set
    CONFIG_KMOD=y

    #
    # Block layer
    #
    CONFIG_BLOCK=y
    # CONFIG_LBD is not set
    # CONFIG_BLK_DEV_IO_TRACE is not set
    # CONFIG_LSF is not set

    #
    # IO Schedulers
    #
    CONFIG_IOSCHED_NOOP=y
    # CONFIG_IOSCHED_AS is not set
    # CONFIG_IOSCHED_DEADLINE is not set
    # CONFIG_IOSCHED_CFQ is not set
    # CONFIG_DEFAULT_AS is not set
    # CONFIG_DEFAULT_DEADLINE is not set
    # CONFIG_DEFAULT_CFQ is not set
    CONFIG_DEFAULT_NOOP=y
    CONFIG_DEFAULT_IOSCHED="noop"

    #
    # System Type
    #
    # CONFIG_ARCH_AAEC2000 is not set
    # CONFIG_ARCH_INTEGRATOR is not set
    # CONFIG_ARCH_REALVIEW is not set
    # CONFIG_ARCH_VERSATILE is not set
    CONFIG_ARCH_AT91=y
    # CONFIG_ARCH_CLPS7500 is not set
    # CONFIG_ARCH_CLPS711X is not set
    # CONFIG_ARCH_CO285 is not set
    # CONFIG_ARCH_EBSA110 is not set
    # CONFIG_ARCH_EP93XX is not set
    # CONFIG_ARCH_FOOTBRIDGE is not set
    # CONFIG_ARCH_NETX is not set
    # CONFIG_ARCH_H720X is not set
    # CONFIG_ARCH_IMX is not set
    # CONFIG_ARCH_IOP32X is not set
    # CONFIG_ARCH_IOP33X is not set
    # CONFIG_ARCH_IOP13XX is not set
    # CONFIG_ARCH_IXP4XX is not set
    # CONFIG_ARCH_IXP2000 is not set
    # CONFIG_ARCH_IXP23XX is not set
    # CONFIG_ARCH_L7200 is not set
    # CONFIG_ARCH_PNX4008 is not set
    # CONFIG_ARCH_PXA is not set
    # CONFIG_ARCH_RPC is not set
    # CONFIG_ARCH_SA1100 is not set
    # CONFIG_ARCH_S3C2410 is not set
    # CONFIG_ARCH_SHARK is not set
    # CONFIG_ARCH_LH7A40X is not set
    # CONFIG_ARCH_OMAP is not set

    #
    # Atmel AT91 System-on-Chip
    #
    # CONFIG_ARCH_AT91RM9200 is not set
    CONFIG_ARCH_AT91SAM9260=y
    # CONFIG_ARCH_AT91SAM9261 is not set
    # CONFIG_ARCH_AT91SAM9263 is not set

    #
    # AT91SAM9260 Variants
    #
    # CONFIG_ARCH_AT91SAM9260_SAM9XE is not set

    #
    # AT91SAM9260 / AT91SAM9XE Board Type
    #
    CONFIG_MACH_AT91SAM9260EK=y

    #
    # AT91 Board Options
    #
    CONFIG_MTD_AT91_DATAFLASH_CARD=y
    CONFIG_MTD_NAND_AT91_BUSWIDTH_16=y

    #
    # AT91 Feature Selections
    #
    CONFIG_AT91_PROGRAMMABLE_CLOCKS=y

    #
    # Processor Type
    #
    CONFIG_CPU_32=y
    CONFIG_CPU_ARM926T=y
    CONFIG_CPU_32v5=y
    CONFIG_CPU_ABRT_EV5TJ=y
    CONFIG_CPU_CACHE_VIVT=y
    CONFIG_CPU_COPY_V4WB=y
    CONFIG_CPU_TLB_V4WBI=y
    CONFIG_CPU_CP15=y
    CONFIG_CPU_CP15_MMU=y

    #
    # Processor Features
    #
    CONFIG_ARM_THUMB=y
    # CONFIG_CPU_ICACHE_DISABLE is not set
    # CONFIG_CPU_DCACHE_DISABLE is not set
    # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
    # CONFIG_CPU_CACHE_ROUND_ROBIN is not set

    #
    # Bus support
    #

    #
    # PCCARD (PCMCIA/CardBus) support
    #
    # CONFIG_PCCARD is not set

    #
    # Kernel Features
    #
    # CONFIG_PREEMPT is not set
    # CONFIG_NO_IDLE_HZ is not set
    CONFIG_HZ=100
    CONFIG_AEABI=y
    CONFIG_OABI_COMPAT=y
    # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
    CONFIG_SELECT_MEMORY_MODEL=y
    CONFIG_FLATMEM_MANUAL=y
    # CONFIG_DISCONTIGMEM_MANUAL is not set
    # CONFIG_SPARSEMEM_MANUAL is not set
    CONFIG_FLATMEM=y
    CONFIG_FLAT_NODE_MEM_MAP=y
    # CONFIG_SPARSEMEM_STATIC is not set
    CONFIG_SPLIT_PTLOCK_CPUS=4096
    CONFIG_RESOURCES_64BIT=y
    CONFIG_LEDS=y
    CONFIG_LEDS_TIMER=y
    CONFIG_LEDS_CPU=y
    CONFIG_ALIGNMENT_TRAP=y

    #
    # Boot options
    #
    CONFIG_ZBOOT_ROM_TEXT=0
    CONFIG_ZBOOT_ROM_BSS=0
    CONFIG_CMDLINE=""
    # CONFIG_XIP_KERNEL is not set

    #
    # Floating point emulation
    #

    #
    # At least one emulation must be selected
    #
    CONFIG_FPE_NWFPE=y
    # CONFIG_FPE_NWFPE_XP is not set
    # CONFIG_FPE_FASTFPE is not set
    # CONFIG_VFP is not set

    #
    # Userspace binary formats
    #
    CONFIG_BINFMT_ELF=y
    # CONFIG_BINFMT_AOUT is not set
    CONFIG_BINFMT_MISC=y

    #
    # Power management options
    #
    # CONFIG_PM is not set
    # CONFIG_APM is not set

    #
    # Networking
    #
    CONFIG_NET=y

    #
    # Networking options
    #
    # CONFIG_NETDEBUG is not set
    CONFIG_PACKET=y
    CONFIG_PACKET_MMAP=y
    CONFIG_UNIX=y
    CONFIG_XFRM=y
    # CONFIG_XFRM_USER is not set
    # CONFIG_XFRM_SUB_POLICY is not set
    CONFIG_NET_KEY=y
    CONFIG_INET=y
    # CONFIG_IP_MULTICAST is not set
    # CONFIG_IP_ADVANCED_ROUTER is not set
    CONFIG_IP_FIB_HASH=y
    CONFIG_IP_PNP=y
    CONFIG_IP_PNP_DHCP=y
    # CONFIG_IP_PNP_BOOTP is not set
    # CONFIG_IP_PNP_RARP is not set
    # CONFIG_NET_IPIP is not set
    # CONFIG_NET_IPGRE is not set
    # CONFIG_ARPD is not set
    # CONFIG_SYN_COOKIES is not set
    # CONFIG_INET_AH is not set
    # CONFIG_INET_ESP is not set
    # CONFIG_INET_IPCOMP is not set
    # CONFIG_INET_XFRM_TUNNEL is not set
    # CONFIG_INET_TUNNEL is not set
    # CONFIG_INET_XFRM_MODE_TRANSPORT is not set
    # CONFIG_INET_XFRM_MODE_TUNNEL is not set
    # CONFIG_INET_XFRM_MODE_BEET is not set
    # CONFIG_INET_DIAG is not set
    # CONFIG_TCP_CONG_ADVANCED is not set
    CONFIG_TCP_CONG_CUBIC=y
    CONFIG_DEFAULT_TCP_CONG="cubic"
    # CONFIG_TCP_MD5SIG is not set
    # CONFIG_IPV6 is not set
    # CONFIG_INET6_XFRM_TUNNEL is not set
    # CONFIG_INET6_TUNNEL is not set
    # CONFIG_NETWORK_SECMARK is not set
    # CONFIG_NETFILTER is not set

    #
    # DCCP Configuration (EXPERIMENTAL)
    #
    # CONFIG_IP_DCCP is not set

    #
    # SCTP Configuration (EXPERIMENTAL)
    #
    # CONFIG_IP_SCTP is not set

    #
    # TIPC Configuration (EXPERIMENTAL)
    #
    # CONFIG_TIPC is not set
    # CONFIG_ATM is not set
    # CONFIG_BRIDGE is not set
    # CONFIG_VLAN_8021Q is not set
    # CONFIG_DECNET is not set
    # CONFIG_LLC2 is not set
    # CONFIG_IPX is not set
    # CONFIG_ATALK is not set
    # CONFIG_X25 is not set
    # CONFIG_LAPB is not set
    # CONFIG_ECONET is not set
    # CONFIG_WAN_ROUTER is not set

    #
    # QoS and/or fair queueing
    #
    # CONFIG_NET_SCHED is not set

    #
    # Network testing
    #
    # CONFIG_NET_PKTGEN is not set
    # CONFIG_HAMRADIO is not set
    # CONFIG_IRDA is not set
    # CONFIG_BT is not set
    # CONFIG_IEEE80211 is not set

    #
    # Device Drivers
    #

    #
    # Generic Driver Options
    #
    CONFIG_STANDALONE=y
    CONFIG_PREVENT_FIRMWARE_BUILD=y
    CONFIG_FW_LOADER=y
    # CONFIG_DEBUG_DRIVER is not set
    # CONFIG_SYS_HYPERVISOR is not set

    #
    # Connector - unified userspace <-> kernelspace linker
    #
    # CONFIG_CONNECTOR is not set

    #
    # Memory Technology Devices (MTD)
    #
    CONFIG_MTD=y
    # CONFIG_MTD_DEBUG is not set
    CONFIG_MTD_CONCAT=y
    CONFIG_MTD_PARTITIONS=y
    CONFIG_MTD_REDBOOT_PARTS=y
    CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
    # CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
    # CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
    # CONFIG_MTD_CMDLINE_PARTS is not set
    # CONFIG_MTD_AFS_PARTS is not set

    #
    # User Modules And Translation Layers
    #
    CONFIG_MTD_CHAR=y
    CONFIG_MTD_BLKDEVS=y
    CONFIG_MTD_BLOCK=y
    CONFIG_FTL=y
    CONFIG_NFTL=y
    CONFIG_NFTL_RW=y
    # CONFIG_INFTL is not set
    # CONFIG_RFD_FTL is not set
    CONFIG_SSFDC=y

    #
    # RAM/ROM/Flash chip drivers
    #
    CONFIG_MTD_CFI=y
    CONFIG_MTD_JEDECPROBE=y
    CONFIG_MTD_GEN_PROBE=y
    # CONFIG_MTD_CFI_ADV_OPTIONS is not set
    CONFIG_MTD_MAP_BANK_WIDTH_1=y
    CONFIG_MTD_MAP_BANK_WIDTH_2=y
    CONFIG_MTD_MAP_BANK_WIDTH_4=y
    # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
    # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
    # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
    CONFIG_MTD_CFI_I1=y
    CONFIG_MTD_CFI_I2=y
    # CONFIG_MTD_CFI_I4 is not set
    # CONFIG_MTD_CFI_I8 is not set
    CONFIG_MTD_CFI_INTELEXT=y
    CONFIG_MTD_CFI_AMDSTD=y
    CONFIG_MTD_CFI_STAA=y
    CONFIG_MTD_CFI_UTIL=y
    CONFIG_MTD_RAM=y
    CONFIG_MTD_ROM=y
    CONFIG_MTD_ABSENT=y
    # CONFIG_MTD_OBSOLETE_CHIPS is not set

    #
    # Mapping drivers for chip access
    #
    CONFIG_MTD_COMPLEX_MAPPINGS=y
    # CONFIG_MTD_PHYSMAP is not set
    # CONFIG_MTD_ARM_INTEGRATOR is not set
    # CONFIG_MTD_IMPA7 is not set
    # CONFIG_MTD_PLATRAM is not set

    #
    # Self-contained MTD device drivers
    #
    CONFIG_MTD_DATAFLASH=y
    # CONFIG_MTD_M25P80 is not set
    # CONFIG_MTD_SLRAM is not set
    # CONFIG_MTD_PHRAM is not set
    # CONFIG_MTD_MTDRAM is not set
    # CONFIG_MTD_BLOCK2MTD is not set

    #
    # Disk-On-Chip Device Drivers
    #
    # CONFIG_MTD_DOC2000 is not set
    # CONFIG_MTD_DOC2001 is not set
    # CONFIG_MTD_DOC2001PLUS is not set

    #
    # NAND Flash Device Drivers
    #
    CONFIG_MTD_NAND=y
    # CONFIG_MTD_NAND_VERIFY_WRITE is not set
    # CONFIG_MTD_NAND_ECC_SMC is not set
    CONFIG_MTD_NAND_IDS=y
    # CONFIG_MTD_NAND_DISKONCHIP is not set
    CONFIG_MTD_NAND_AT91=y
    # CONFIG_MTD_NAND_NANDSIM is not set

    #
    # OneNAND Flash Device Drivers
    #
    # CONFIG_MTD_ONENAND is not set

    #
    # Parallel port support
    #
    # CONFIG_PARPORT is not set

    #
    # Plug and Play support
    #

    #
    # Block devices
    #
    # CONFIG_BLK_DEV_COW_COMMON is not set
    CONFIG_BLK_DEV_LOOP=y
    # CONFIG_BLK_DEV_CRYPTOLOOP is not set
    # CONFIG_BLK_DEV_NBD is not set
    # CONFIG_BLK_DEV_UB is not set
    CONFIG_BLK_DEV_RAM=y
    CONFIG_BLK_DEV_RAM_COUNT=16
    CONFIG_BLK_DEV_RAM_SIZE=16384
    CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
    CONFIG_BLK_DEV_INITRD=y
    # CONFIG_CDROM_PKTCDVD is not set
    # CONFIG_ATA_OVER_ETH is not set

    #
    # SCSI device support
    #
    # CONFIG_RAID_ATTRS is not set
    # CONFIG_SCSI is not set
    # CONFIG_SCSI_NETLINK is not set

    #
    # Serial ATA (prod) and Parallel ATA (experimental) drivers
    #
    # CONFIG_ATA is not set

    #
    # Multi-device support (RAID and LVM)
    #
    # CONFIG_MD is not set

    #
    # Fusion MPT device support
    #
    # CONFIG_FUSION is not set

    #
    # IEEE 1394 (FireWire) support
    #

    #
    # I2O device support
    #

    #
    # Network device support
    #
    CONFIG_NETDEVICES=y
    CONFIG_DUMMY=y
    # CONFIG_BONDING is not set
    # CONFIG_EQUALIZER is not set
    # CONFIG_TUN is not set

    #
    # PHY device support
    #
    CONFIG_PHYLIB=y

    #
    # MII PHY device drivers
    #
    # CONFIG_MARVELL_PHY is not set
    CONFIG_DAVICOM_PHY=y
    # CONFIG_QSEMI_PHY is not set
    # CONFIG_LXT_PHY is not set
    # CONFIG_CICADA_PHY is not set
    # CONFIG_VITESSE_PHY is not set
    # CONFIG_SMSC_PHY is not set
    # CONFIG_BROADCOM_PHY is not set
    # CONFIG_FIXED_PHY is not set

    #
    # Ethernet (10 or 100Mbit)
    #
    CONFIG_NET_ETHERNET=y
    CONFIG_MII=y
    CONFIG_MACB=y
    # CONFIG_SMC91X is not set
    CONFIG_DM9000=y

    #
    # Ethernet (1000 Mbit)
    #

    #
    # Ethernet (10000 Mbit)
    #

    #
    # Token Ring devices
    #

    #
    # Wireless LAN (non-hamradio)
    #
    # CONFIG_NET_RADIO is not set

    #
    # Wan interfaces
    #
    # CONFIG_WAN is not set
    # CONFIG_PPP is not set
    # CONFIG_SLIP is not set
    # CONFIG_SHAPER is not set
    # CONFIG_NETCONSOLE is not set
    # CONFIG_NETPOLL is not set
    # CONFIG_NET_POLL_CONTROLLER is not set

    #
    # ISDN subsystem
    #
    # CONFIG_ISDN is not set

    #
    # Input device support
    #
    CONFIG_INPUT=y
    # CONFIG_INPUT_FF_MEMLESS is not set

    #
    # Userland interfaces
    #
    CONFIG_INPUT_MOUSEDEV=y
    # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
    CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
    CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
    # CONFIG_INPUT_JOYDEV is not set
    # CONFIG_INPUT_TSDEV is not set
    # CONFIG_INPUT_EVDEV is not set
    # CONFIG_INPUT_EVBUG is not set

    #
    # Input Device Drivers
    #
    # CONFIG_INPUT_KEYBOARD is not set
    # CONFIG_INPUT_MOUSE is not set
    # CONFIG_INPUT_JOYSTICK is not set
    # CONFIG_INPUT_TOUCHSCREEN is not set
    # CONFIG_INPUT_MISC is not set

    #
    # Hardware I/O ports
    #
    CONFIG_SERIO=y
    CONFIG_SERIO_SERPORT=y
    # CONFIG_SERIO_RAW is not set
    # CONFIG_GAMEPORT is not set

    #
    # Character devices
    #
    CONFIG_VT=y
    CONFIG_VT_CONSOLE=y
    CONFIG_HW_CONSOLE=y
    # CONFIG_VT_HW_CONSOLE_BINDING is not set
    # CONFIG_SERIAL_NONSTANDARD is not set

    #
    # Serial drivers
    #
    CONFIG_SERIAL_8250=y
    CONFIG_SERIAL_8250_CONSOLE=y
    CONFIG_SERIAL_8250_NR_UARTS=4
    CONFIG_SERIAL_8250_RUNTIME_UARTS=4
    CONFIG_SERIAL_8250_EXTENDED=y
    # CONFIG_SERIAL_8250_MANY_PORTS is not set
    CONFIG_SERIAL_8250_SHARE_IRQ=y
    CONFIG_SERIAL_8250_DETECT_IRQ=y
    CONFIG_SERIAL_8250_RSA=y

    #
    # Non-8250 serial port support
    #
    CONFIG_SERIAL_ATMEL=y
    CONFIG_SERIAL_ATMEL_CONSOLE=y
    # CONFIG_SERIAL_ATMEL_TTYAT is not set
    CONFIG_SERIAL_CORE=y
    CONFIG_SERIAL_CORE_CONSOLE=y
    CONFIG_UNIX98_PTYS=y
    # CONFIG_LEGACY_PTYS is not set

    #
    # IPMI
    #
    # CONFIG_IPMI_HANDLER is not set

    #
    # Watchdog Cards
    #
    # CONFIG_WATCHDOG is not set
    # CONFIG_HW_RANDOM is not set
    # CONFIG_NVRAM is not set
    # CONFIG_DTLK is not set
    # CONFIG_R3964 is not set
    # CONFIG_RAW_DRIVER is not set

    #
    # TPM devices
    #
    # CONFIG_TCG_TPM is not set

    #
    # I2C support
    #
    CONFIG_I2C=y
    CONFIG_I2C_CHARDEV=y

    #
    # I2C Algorithms
    #
    # CONFIG_I2C_ALGOBIT is not set
    # CONFIG_I2C_ALGOPCF is not set
    # CONFIG_I2C_ALGOPCA is not set

    #
    # I2C Hardware Bus support
    #
    # CONFIG_I2C_ATMELTWI is not set
    CONFIG_I2C_AT91=y
    CONFIG_I2C_AT91_CLOCKRATE=100000
    # CONFIG_I2C_OCORES is not set
    # CONFIG_I2C_PARPORT_LIGHT is not set
    # CONFIG_I2C_STUB is not set
    # CONFIG_I2C_PCA_ISA is not set

    #
    # Miscellaneous I2C Chip support
    #
    # CONFIG_SENSORS_DS1337 is not set
    # CONFIG_SENSORS_DS1374 is not set
    # CONFIG_SENSORS_EEPROM is not set
    # CONFIG_SENSORS_PCF8574 is not set
    # CONFIG_SENSORS_PCA9539 is not set
    # CONFIG_SENSORS_PCF8591 is not set
    # CONFIG_SENSORS_MAX6875 is not set
    # CONFIG_I2C_DEBUG_CORE is not set
    # CONFIG_I2C_DEBUG_ALGO is not set
    # CONFIG_I2C_DEBUG_BUS is not set
    # CONFIG_I2C_DEBUG_CHIP is not set

    #
    # SPI support
    #
    CONFIG_SPI=y
    # CONFIG_SPI_DEBUG is not set
    CONFIG_SPI_MASTER=y

    #
    # SPI Master Controller Drivers
    #
    CONFIG_SPI_ATMEL=y
    # CONFIG_SPI_BITBANG is not set

    #
    # SPI Protocol Masters
    #

    #
    # Dallas's 1-wire bus
    #
    # CONFIG_W1 is not set

    #
    # Hardware Monitoring support
    #
    # CONFIG_HWMON is not set
    # CONFIG_HWMON_VID is not set

    #
    # Misc devices
    #
    # CONFIG_TIFM_CORE is not set

    #
    # LED devices
    #
    CONFIG_NEW_LEDS=y
    CONFIG_LEDS_CLASS=y

    #
    # LED drivers
    #

    #
    # LED Triggers
    #
    CONFIG_LEDS_TRIGGERS=y
    CONFIG_LEDS_TRIGGER_TIMER=y
    CONFIG_LEDS_TRIGGER_HEARTBEAT=y

    #
    # Multimedia devices
    #
    # CONFIG_VIDEO_DEV is not set

    #
    # Digital Video Broadcasting Devices
    #
    # CONFIG_DVB is not set
    # CONFIG_USB_DABUSB is not set

    #
    # Graphics support
    #
    # CONFIG_FIRMWARE_EDID is not set
    # CONFIG_FB is not set

    #
    # Console display driver support
    #
    # CONFIG_VGA_CONSOLE is not set
    CONFIG_DUMMY_CONSOLE=y
    # CONFIG_BACKLIGHT_LCD_SUPPORT is not set

    #
    # Sound
    #
    # CONFIG_SOUND is not set

    #
    # HID Devices
    #
    CONFIG_HID=y

    #
    # USB support
    #
    CONFIG_USB_ARCH_HAS_HCD=y
    CONFIG_USB_ARCH_HAS_OHCI=y
    # CONFIG_USB_ARCH_HAS_EHCI is not set
    CONFIG_USB=y
    # CONFIG_USB_DEBUG is not set

    #
    # Miscellaneous USB options
    #
    CONFIG_USB_DEVICEFS=y
    # CONFIG_USB_BANDWIDTH is not set
    # CONFIG_USB_DYNAMIC_MINORS is not set
    # CONFIG_USB_OTG is not set

    #
    # USB Host Controller Drivers
    #
    # CONFIG_USB_ISP116X_HCD is not set
    CONFIG_USB_OHCI_HCD=y
    # CONFIG_USB_OHCI_BIG_ENDIAN is not set
    CONFIG_USB_OHCI_LITTLE_ENDIAN=y
    # CONFIG_USB_SL811_HCD is not set

    #
    # USB Device Class drivers
    #
    # CONFIG_USB_ACM is not set
    # CONFIG_USB_PRINTER is not set

    #
    # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
    #

    #
    # may also be needed; see USB_STORAGE Help for more information
    #
    # CONFIG_USB_LIBUSUAL is not set

    #
    # USB Input Devices
    #
    CONFIG_USB_HID=y
    # CONFIG_USB_HIDINPUT_POWERBOOK is not set
    # CONFIG_HID_FF is not set
    # CONFIG_USB_HIDDEV is not set
    # CONFIG_USB_AIPTEK is not set
    # CONFIG_USB_WACOM is not set
    # CONFIG_USB_ACECAD is not set
    # CONFIG_USB_KBTAB is not set
    # CONFIG_USB_POWERMATE is not set
    # CONFIG_USB_TOUCHSCREEN is not set
    # CONFIG_USB_YEALINK is not set
    # CONFIG_USB_XPAD is not set
    # CONFIG_USB_ATI_REMOTE is not set
    # CONFIG_USB_ATI_REMOTE2 is not set
    # CONFIG_USB_KEYSPAN_REMOTE is not set
    # CONFIG_USB_APPLETOUCH is not set

    #
    # USB Imaging devices
    #
    # CONFIG_USB_MDC800 is not set

    #
    # USB Network Adapters
    #
    # CONFIG_USB_CATC is not set
    # CONFIG_USB_KAWETH is not set
    # CONFIG_USB_PEGASUS is not set
    # CONFIG_USB_RTL8150 is not set
    # CONFIG_USB_USBNET_MII is not set
    # CONFIG_USB_USBNET is not set
    # CONFIG_USB_MON is not set

    #
    # USB port drivers
    #

    #
    # USB Serial Converter support
    #
    CONFIG_USB_SERIAL=y
    # CONFIG_USB_SERIAL_CONSOLE is not set
    CONFIG_USB_SERIAL_GENERIC=y
    # CONFIG_USB_SERIAL_AIRCABLE is not set
    # CONFIG_USB_SERIAL_AIRPRIME is not set
    # CONFIG_USB_SERIAL_ARK3116 is not set
    # CONFIG_USB_SERIAL_BELKIN is not set
    # CONFIG_USB_SERIAL_WHITEHEAT is not set
    # CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
    CONFIG_USB_SERIAL_CP2101=y
    # CONFIG_USB_SERIAL_CYPRESS_M8 is not set
    # CONFIG_USB_SERIAL_EMPEG is not set
    # CONFIG_USB_SERIAL_FTDI_SIO is not set
    # CONFIG_USB_SERIAL_FUNSOFT is not set
    # CONFIG_USB_SERIAL_VISOR is not set
    # CONFIG_USB_SERIAL_IPAQ is not set
    # CONFIG_USB_SERIAL_IR is not set
    # CONFIG_USB_SERIAL_EDGEPORT is not set
    # CONFIG_USB_SERIAL_EDGEPORT_TI is not set
    # CONFIG_USB_SERIAL_GARMIN is not set
    # CONFIG_USB_SERIAL_IPW is not set
    # CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
    # CONFIG_USB_SERIAL_KEYSPAN is not set
    # CONFIG_USB_SERIAL_KLSI is not set
    # CONFIG_USB_SERIAL_KOBIL_SCT is not set
    # CONFIG_USB_SERIAL_MCT_U232 is not set
    # CONFIG_USB_SERIAL_MOS7720 is not set
    # CONFIG_USB_SERIAL_MOS7840 is not set
    # CONFIG_USB_SERIAL_NAVMAN is not set
    # CONFIG_USB_SERIAL_PL2303 is not set
    # CONFIG_USB_SERIAL_HP4X is not set
    # CONFIG_USB_SERIAL_SAFE is not set
    # CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
    # CONFIG_USB_SERIAL_TI is not set
    # CONFIG_USB_SERIAL_CYBERJACK is not set
    # CONFIG_USB_SERIAL_XIRCOM is not set
    # CONFIG_USB_SERIAL_OPTION is not set
    # CONFIG_USB_SERIAL_OMNINET is not set
    # CONFIG_USB_SERIAL_DEBUG is not set

    #
    # USB Miscellaneous drivers
    #
    # CONFIG_USB_EMI62 is not set
    # CONFIG_USB_EMI26 is not set
    # CONFIG_USB_ADUTUX is not set
    # CONFIG_USB_AUERSWALD is not set
    # CONFIG_USB_RIO500 is not set
    # CONFIG_USB_LEGOTOWER is not set
    # CONFIG_USB_LCD is not set
    # CONFIG_USB_LED is not set
    # CONFIG_USB_CYPRESS_CY7C63 is not set
    # CONFIG_USB_CYTHERM is not set
    # CONFIG_USB_PHIDGET is not set
    # CONFIG_USB_IDMOUSE is not set
    # CONFIG_USB_FTDI_ELAN is not set
    # CONFIG_USB_APPLEDISPLAY is not set
    # CONFIG_USB_LD is not set
    # CONFIG_USB_TRANCEVIBRATOR is not set
    # CONFIG_USB_TEST is not set

    #
    # USB DSL modem support
    #

    #
    # USB Gadget Support
    #
    CONFIG_USB_GADGET=y
    # CONFIG_USB_GADGET_DEBUG_FILES is not set
    CONFIG_USB_GADGET_SELECTED=y
    # CONFIG_USB_GADGET_NET2280 is not set
    # CONFIG_USB_GADGET_PXA2XX is not set
    # CONFIG_USB_GADGET_GOKU is not set
    # CONFIG_USB_GADGET_LH7A40X is not set
    # CONFIG_USB_GADGET_HUSB2DEV is not set
    # CONFIG_USB_GADGET_OMAP is not set
    CONFIG_USB_GADGET_AT91=y
    CONFIG_USB_AT91=y
    # CONFIG_USB_GADGET_DUMMY_HCD is not set
    # CONFIG_USB_GADGET_DUALSPEED is not set
    # CONFIG_USB_ZERO is not set
    CONFIG_USB_ETH=y
    # CONFIG_USB_ETH_RNDIS is not set
    # CONFIG_USB_GADGETFS is not set
    # CONFIG_USB_FILE_STORAGE is not set
    # CONFIG_USB_G_SERIAL is not set
    # CONFIG_USB_MIDI_GADGET is not set

    #
    # MMC/SD Card support
    #
    CONFIG_MMC=y
    # CONFIG_MMC_DEBUG is not set
    CONFIG_MMC_BLOCK=y
    CONFIG_MMC_AT91=y
    # CONFIG_MMC_TIFM_SD is not set

    #
    # Real Time Clock
    #
    CONFIG_RTC_LIB=y
    # CONFIG_RTC_CLASS is not set

    #
    # File systems
    #
    CONFIG_EXT2_FS=y
    CONFIG_EXT2_FS_XATTR=y
    CONFIG_EXT2_FS_POSIX_ACL=y
    CONFIG_EXT2_FS_SECURITY=y
    # CONFIG_EXT2_FS_XIP is not set
    CONFIG_EXT3_FS=y
    CONFIG_EXT3_FS_XATTR=y
    # CONFIG_EXT3_FS_POSIX_ACL is not set
    # CONFIG_EXT3_FS_SECURITY is not set
    # CONFIG_EXT4DEV_FS is not set
    CONFIG_JBD=y
    # CONFIG_JBD_DEBUG is not set
    CONFIG_FS_MBCACHE=y
    # CONFIG_REISERFS_FS is not set
    # CONFIG_JFS_FS is not set
    CONFIG_FS_POSIX_ACL=y
    # CONFIG_XFS_FS is not set
    # CONFIG_GFS2_FS is not set
    # CONFIG_OCFS2_FS is not set
    # CONFIG_MINIX_FS is not set
    # CONFIG_ROMFS_FS is not set
    # CONFIG_INOTIFY is not set
    # CONFIG_QUOTA is not set
    CONFIG_DNOTIFY=y
    # CONFIG_AUTOFS_FS is not set
    # CONFIG_AUTOFS4_FS is not set
    # CONFIG_FUSE_FS is not set

    #
    # CD-ROM/DVD Filesystems
    #
    # CONFIG_ISO9660_FS is not set
    # CONFIG_UDF_FS is not set

    #
    # DOS/FAT/NT Filesystems
    #
    # CONFIG_MSDOS_FS is not set
    # CONFIG_VFAT_FS is not set
    # CONFIG_NTFS_FS is not set

    #
    # Pseudo filesystems
    #
    CONFIG_PROC_FS=y
    CONFIG_PROC_SYSCTL=y
    CONFIG_SYSFS=y
    CONFIG_TMPFS=y
    # CONFIG_TMPFS_POSIX_ACL is not set
    # CONFIG_HUGETLB_PAGE is not set
    CONFIG_RAMFS=y
    CONFIG_CONFIGFS_FS=y

    #
    # Miscellaneous filesystems
    #
    # CONFIG_ADFS_FS is not set
    # CONFIG_AFFS_FS is not set
    # CONFIG_HFS_FS is not set
    # CONFIG_HFSPLUS_FS is not set
    # CONFIG_BEFS_FS is not set
    # CONFIG_BFS_FS is not set
    # CONFIG_EFS_FS is not set
    CONFIG_JFFS2_FS=y
    CONFIG_JFFS2_FS_DEBUG=0
    CONFIG_JFFS2_FS_WRITEBUFFER=y
    # CONFIG_JFFS2_SUMMARY is not set
    # CONFIG_JFFS2_FS_XATTR is not set
    # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
    CONFIG_JFFS2_ZLIB=y
    CONFIG_JFFS2_RTIME=y
    # CONFIG_JFFS2_RUBIN is not set
    CONFIG_CRAMFS=y
    # CONFIG_VXFS_FS is not set
    # CONFIG_HPFS_FS is not set
    # CONFIG_QNX4FS_FS is not set
    # CONFIG_SYSV_FS is not set
    # CONFIG_UFS_FS is not set

    #
    # Network File Systems
    #
    # CONFIG_NFS_FS is not set
    # CONFIG_NFSD is not set
    # CONFIG_SMB_FS is not set
    # CONFIG_CIFS is not set
    # CONFIG_NCP_FS is not set
    # CONFIG_CODA_FS is not set
    # CONFIG_AFS_FS is not set
    # CONFIG_9P_FS is not set

    #
    # Partition Types
    #
    # CONFIG_PARTITION_ADVANCED is not set
    CONFIG_MSDOS_PARTITION=y

    #
    # Native Language Support
    #
    # CONFIG_NLS is not set

    #
    # Distributed Lock Manager
    #
    # CONFIG_DLM is not set

    #
    # Profiling support
    #
    # CONFIG_PROFILING is not set

    #
    # Kernel hacking
    #
    # CONFIG_PRINTK_TIME is not set
    CONFIG_ENABLE_MUST_CHECK=y
    CONFIG_MAGIC_SYSRQ=y
    # CONFIG_UNUSED_SYMBOLS is not set
    # CONFIG_DEBUG_FS is not set
    # CONFIG_HEADERS_CHECK is not set
    CONFIG_DEBUG_KERNEL=y
    CONFIG_LOG_BUF_SHIFT=17
    CONFIG_DETECT_SOFTLOCKUP=y
    # CONFIG_SCHEDSTATS is not set
    # CONFIG_DEBUG_SLAB is not set
    # CONFIG_DEBUG_RT_MUTEXES is not set
    # CONFIG_RT_MUTEX_TESTER is not set
    CONFIG_DEBUG_SPINLOCK=y
    # CONFIG_DEBUG_MUTEXES is not set
    # CONFIG_DEBUG_RWSEMS is not set
    CONFIG_DEBUG_SPINLOCK_SLEEP=y
    # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
    # CONFIG_DEBUG_KOBJECT is not set
    CONFIG_DEBUG_BUGVERBOSE=y
    # CONFIG_DEBUG_INFO is not set
    # CONFIG_DEBUG_VM is not set
    # CONFIG_DEBUG_LIST is not set
    CONFIG_FRAME_POINTER=y
    CONFIG_FORCED_INLINING=y
    # CONFIG_RCU_TORTURE_TEST is not set
    # CONFIG_DEBUG_USER is not set
    # CONFIG_DEBUG_ERRORS is not set
    # CONFIG_DEBUG_LL is not set

    #
    # Security options
    #
    # CONFIG_KEYS is not set
    # CONFIG_SECURITY is not set

    #
    # Cryptographic options
    #
    CONFIG_CRYPTO=y
    CONFIG_CRYPTO_ALGAPI=y
    CONFIG_CRYPTO_HASH=y
    CONFIG_CRYPTO_MANAGER=y
    CONFIG_CRYPTO_HMAC=y
    # CONFIG_CRYPTO_XCBC is not set
    # CONFIG_CRYPTO_NULL is not set
    # CONFIG_CRYPTO_MD4 is not set
    CONFIG_CRYPTO_MD5=y
    # CONFIG_CRYPTO_SHA1 is not set
    # CONFIG_CRYPTO_SHA256 is not set
    # CONFIG_CRYPTO_SHA512 is not set
    # CONFIG_CRYPTO_WP512 is not set
    # CONFIG_CRYPTO_TGR192 is not set
    # CONFIG_CRYPTO_GF128MUL is not set
    # CONFIG_CRYPTO_ECB is not set
    # CONFIG_CRYPTO_CBC is not set
    # CONFIG_CRYPTO_LRW is not set
    # CONFIG_CRYPTO_DES is not set
    # CONFIG_CRYPTO_BLOWFISH is not set
    # CONFIG_CRYPTO_TWOFISH is not set
    # CONFIG_CRYPTO_SERPENT is not set
    # CONFIG_CRYPTO_AES is not set
    # CONFIG_CRYPTO_CAST5 is not set
    # CONFIG_CRYPTO_CAST6 is not set
    # CONFIG_CRYPTO_TEA is not set
    # CONFIG_CRYPTO_ARC4 is not set
    # CONFIG_CRYPTO_KHAZAD is not set
    # CONFIG_CRYPTO_ANUBIS is not set
    # CONFIG_CRYPTO_DEFLATE is not set
    # CONFIG_CRYPTO_MICHAEL_MIC is not set
    # CONFIG_CRYPTO_CRC32C is not set
    # CONFIG_CRYPTO_TEST is not set

    #
    # Hardware crypto devices
    #

    #
    # Library routines
    #
    CONFIG_BITREVERSE=y
    CONFIG_CRC_CCITT=y
    CONFIG_CRC16=y
    CONFIG_CRC32=y
    CONFIG_LIBCRC32C=y
    CONFIG_ZLIB_INFLATE=y
    CONFIG_ZLIB_DEFLATE=y
    CONFIG_PLIST=y
    CONFIG_IOMAP_COPY=y






    --
    Ryan Ordway E-mail: rordway@oregonstate.edu
    Unix Systems Administrator rordway@library.oregonstate.edu
    OSU Libraries, Corvallis, OR 97370 Office: Valley Library #4657


    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2007-05-04 21:49    [W:0.123 / U:123.696 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site