lkml.org 
[lkml]   [2007]   [Apr]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: suspend2 merge (was Re: [Suspend2-devel] Re: CFS and suspend2: hang in atomic copy)


On Wed, 25 Apr 2007, Linus Torvalds wrote:
>
> The *thaw* needs to happen with devices quiescent.

Btw, I sure as hell hope you didn't use "suspend()" for that. You're
(again) much better off having a totally separate function that just
freezes stuff.

So in the "snapshot+shutdown" path, you should have:

- prepare_to_snapshot() - allocate memory, and possibly return errors

We can skip this, if we just make the rule be that any devices that
want to support snapshotting must always have the memory required for
snapshotting pre-allocated. Most devices really do allocate memory for
their state anyway, and the only real reason for the "prepare" stage
here is becasue the final snapshot has to happen with interrupts off,
obviously. So *if* we don't need to allocate any memory, and if we
don't expect to want to accept some early error case, this is likely
useless.

- snapshot() - actually save device state that is consistent with the
memory image at the time. Called with interrupts off, but the device
has to be usable both before and afterwards!

And I would seriously suggest that "snapshot()" be documented to not rely
on any DMA memory, exactly because the device has to be accessible both
before and after (before - because we're running and allocating memory,
and after - because we'll be writing thigns out). But see later:

For the "resume snapshot" path, I would suggest having

- freeze(): quiesce the device. This literally just does the absolute
minimum to make sure that the device doesn't do anything surprising (no
interrupts, no DMA, no nothing). For many devices, it's a no-op, even
if they can do DMA (eg most disk controllers will do DMA, but only as
an actual result of a request, and upper layers will be quiescent
anyway, so they do *not* need to disable DMA)

NOTE! The "freeze()" gets called from the *old* kernel just _before_ a
snapshot unpacking!!

- restart_snapshot() - actually restart the snapshot (and usually this
would involve re-setting the device, not so much trying to restore all
the saved state. IOW, it's easier to just re-initialize the DMA command
queues than to try to make them "atomic" in the snapshot).

NOTE! This gets called by the *new* kernel _after_ the snapshot resume!

And if you *want* to, I can see that you might want to actually do a
"unfreeze()" thing too, and make the actual shapshotting be:

/* We may not even need this.. */
for_each_device() {
err = prepare_to_snapshot();
if (err)
return err;
}

/* This is the real work for snapshotting */
cli();
for_each_device()
freeze(dev);
for_each_device()
snapshot(dev);
.. snapshot current memory image ..
for_each_device_depth_first()
unfreeze(dev);
sti();

and maybe it's worth it, but I would almost suggest that you just make the
rule be that any DMA etc just *has* to be re-initialized by
"restart_snapshot()", in which case it's not even necessary to
freeze/unfreeze over the device, and "snapshot()" itself only needs to
make sure any non-DMA data is safe.

But adding the freeze/unfreeze (which is a no-op for most hardware anyway)
might make things easier to think about, so I would certainly not *object*
to it, even if I suspect it's not necessary.

Anyway, the restore_snapshot() sequence should be:

/* Old kernel.. Normal boot, load snapshot image */
cli()
for_each_device()
freeze(dev);
restore_snapshot_image();
restore_regs_and_jump_to_image();
/* noreturn */


/* New kernel, gets called at the snapshot restore address
* with interrupts off and devices frozen, and memory image
* constsntent with what it was at "snapshot()" time
*/
for_each_dev_depth_first()
restore_snapshot(dev);
/* And if you want to, just to be "symmetric"

for_each_dev_depth_first()
unfreeze(dev)

although I think you could just make "restore_snapshot()"
implicitly unfreeze it too..
*/
sti();
/* We're up */

and notice how *different* this is from what happens for s2ram. There
really isn't anything in common here. Exactly because s2ram simply doesn't
_have_ any of the issues with atomic memory images.

So s2ram is just

for_each_dev()
suspend(dev);
cli();
for_each_dev()
late_suspend(dev);
.. go to sleep ..
for_each_dev_depth_first()
early_resume(dev);
sti();
for_each_dev_depth_first()
resume(dev);

and has none of the "freeze" issues at all.

Doesn't that seem a lot more straightforward? Yes, it's more functions,
but each function is a lot more obvious. This follows the unix rule of "do
one thing, and do that thing well", instead of trying to make one function
do many very different things depending on what you actually want done..

Linus
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2007-04-26 02:37    [W:0.300 / U:0.508 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site