Messages in this thread | | | Date | Wed, 28 Mar 2007 13:55:54 -0700 | From | "Miles Lane" <> | Subject | 2.6.21-rc5-mm2 -- ACPI problems (lid switch broken, always shows running from AC, plugging in AC hangs machine) |
| |
Hello,
My laptop (HP dv1240us) is always showing that my laptop is plugged into AC power, even when it is running off of the battery. When I plug into the AC after running on the battery, the machine immediately locks up. Also, the laptop lid button isn't working -- pressing it doesn't trigger a suspend.
# # Power management options (ACPI, APM) # CONFIG_PM=y # CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set # CONFIG_PM_SYSFS_DEPRECATED is not set CONFIG_SOFTWARE_SUSPEND=y CONFIG_PM_STD_PARTITION=""
# # ACPI (Advanced Configuration and Power Interface) Support # CONFIG_ACPI=y CONFIG_ACPI_SLEEP=y CONFIG_ACPI_SLEEP_PROC_FS=y # CONFIG_ACPI_SLEEP_PROC_SLEEP is not set # CONFIG_ACPI_PROCFS is not set CONFIG_ACPI_AC=m CONFIG_ACPI_BATTERY=m CONFIG_ACPI_BUTTON=m CONFIG_ACPI_VIDEO=m CONFIG_ACPI_FAN=m CONFIG_ACPI_DOCK=m # CONFIG_ACPI_BAY is not set CONFIG_ACPI_PROCESSOR=m CONFIG_ACPI_THERMAL=m CONFIG_ACPI_ASUS=m CONFIG_ACPI_TOSHIBA=m CONFIG_ACPI_BLACKLIST_YEAR=2000 CONFIG_ACPI_DEBUG=y CONFIG_ACPI_EC=y CONFIG_ACPI_POWER=y CONFIG_ACPI_SYSTEM=y CONFIG_X86_PM_TIMER=y CONFIG_ACPI_CONTAINER=m CONFIG_ACPI_SBS=m
CONFIG_APM=m # CONFIG_APM_IGNORE_USER_SUSPEND is not set # CONFIG_APM_DO_ENABLE is not set # CONFIG_APM_CPU_IDLE is not set # CONFIG_APM_DISPLAY_BLANK is not set # CONFIG_APM_ALLOW_INTS is not set # CONFIG_APM_REAL_MODE_POWER_OFF is not set
# # CPU Frequency scaling # CONFIG_CPU_FREQ=y CONFIG_CPU_FREQ_TABLE=m CONFIG_CPU_FREQ_DEBUG=y CONFIG_CPU_FREQ_STAT=m CONFIG_CPU_FREQ_STAT_DETAILS=y # CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y CONFIG_CPU_FREQ_GOV_PERFORMANCE=m CONFIG_CPU_FREQ_GOV_POWERSAVE=m CONFIG_CPU_FREQ_GOV_USERSPACE=y CONFIG_CPU_FREQ_GOV_ONDEMAND=m CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
# # CPUFreq processor drivers # CONFIG_X86_ACPI_CPUFREQ=m # CONFIG_X86_POWERNOW_K6 is not set # CONFIG_X86_POWERNOW_K7 is not set # CONFIG_X86_POWERNOW_K8 is not set # CONFIG_X86_GX_SUSPMOD is not set # CONFIG_X86_SPEEDSTEP_CENTRINO is not set CONFIG_X86_SPEEDSTEP_ICH=m
CONFIG_X86_SPEEDSTEP_LIB=m CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK=y
# # CPU idle PM support # # CONFIG_CPU_IDLE is not set
[ 0.000000] Linux version 2.6.21-rc5-mm2 (root@FractalPath) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #7 Wed Mar 28 10:55:43 PDT 2007 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] sanitize start [ 0.000000] sanitize end [ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2 [ 0.000000] copy_e820_map() start: 00000000000ce000 size: 0000000000002000 end: 00000000000d0000 type: 2 [ 0.000000] copy_e820_map() start: 00000000000dc000 size: 0000000000024000 end: 0000000000100000 type: 2 [ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000003dde0000 end: 000000003dee0000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000003dee0000 size: 000000000000c000 end: 000000003deec000 type: 3 [ 0.000000] copy_e820_map() start: 000000003deec000 size: 0000000000014000 end: 000000003df00000 type: 4 [ 0.000000] copy_e820_map() start: 000000003df00000 size: 0000000002100000 end: 0000000040000000 type: 2 [ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2 [ 0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2 [ 0.000000] copy_e820_map() start: 00000000ff800000 size: 0000000000400000 end: 00000000ffc00000 type: 2 [ 0.000000] copy_e820_map() start: 00000000fffffc00 size: 0000000000000400 end: 0000000100000000 type: 2 [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved) [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003dee0000 (usable) [ 0.000000] BIOS-e820: 000000003dee0000 - 000000003deec000 (ACPI data) [ 0.000000] BIOS-e820: 000000003deec000 - 000000003df00000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003df00000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved) [ 0.000000] BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved) [ 0.000000] 94MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f7e30 [ 0.000000] Entering add_active_range(0, 0, 253664) 0 entries of 256 used [ 0.000000] sizeof(struct page) = 32 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 253664 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 253664 [ 0.000000] On node 0 totalpages: 253664 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 189 pages used for memmap [ 0.000000] HighMem zone: 24099 pages, LIFO batch:3 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP 000F7E00, 0014 (r0 HP ) [ 0.000000] ACPI: RSDT 3DEE76BB, 0040 (r1 HP 09B8 6040000 LTP 0) [ 0.000000] ACPI: FACP 3DEEBE8C, 0074 (r1 HP 09B8 6040000 PTL 50) [ 0.000000] ACPI: DSDT 3DEE7B9A, 42F2 (r1 HP 09B8 6040000 MSFT 100000E) [ 0.000000] ACPI: FACS 3DEFCFC0, 0040 [ 0.000000] ACPI: HPET 3DEEBF00, 0038 (r1 HP 09B8 6040000 PTL 0) [ 0.000000] ACPI: APIC 3DEEBF38, 005A (r1 HP 09B8 6040000 PTL 50) [ 0.000000] ACPI: APIC 3DEEBF92, 0046 (r1 HP 09B8 6040000 PTL 0) [ 0.000000] ACPI: BOOT 3DEEBFD8, 0028 (r1 HP 09B8 6040000 LTP 1) [ 0.000000] ACPI: SSDT 3DEE7AFE, 009C (r1 HP 09B8 1 INTL 20030224) [ 0.000000] ACPI: SSDT 3DEE76FB, 0277 (r1 HP 09B8 2000 INTL 20030224) [ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 2 [ 0.000000] ACPI: If "acpi_apic_instance=0" works better, notify linux-acpi@vger.kernel.org [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 6:13 APIC version 20 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0x0 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) [ 0.000000] Built 1 zonelists. Total pages: 251683 [ 0.000000] Kernel command line: root=UUID=47a91ab9-c44b-4802-8012-5748803bb3ef pci=assign-busses vga=0x27e ro splash [ 0.000000] mapped APIC to ffffd000 (fee00000) [ 0.000000] mapped IOAPIC to ffffc000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 1695.771 MHz processor. [ 57.648280] Console: colour VGA+ 80x60 [ 57.653235] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 57.653359] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 57.653435] ... MAX_LOCK_DEPTH: 30 [ 57.653512] ... MAX_LOCKDEP_KEYS: 2048 [ 57.653588] ... CLASSHASH_SIZE: 1024 [ 57.653665] ... MAX_LOCKDEP_ENTRIES: 8192 [ 57.653742] ... MAX_LOCKDEP_CHAINS: 16384 [ 57.653819] ... CHAINHASH_SIZE: 8192 [ 57.653896] memory used by lock dependency info: 992 kB [ 57.653975] per task-struct memory footprint: 1200 bytes [ 57.654496] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 57.655077] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 57.693759] Memory: 996500k/1014656k available (1671k kernel code, 17420k reserved, 885k data, 176k init, 97152k highmem) [ 57.693898] virtual kernel memory layout: [ 57.693899] fixmap : 0xfff9c000 - 0xfffff000 ( 396 kB) [ 57.693901] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 57.693902] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 57.693903] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 57.693905] .init : 0xc0382000 - 0xc03ae000 ( 176 kB) [ 57.693906] .data : 0xc02a1e0c - 0xc037f4b4 ( 885 kB) [ 57.693907] .text : 0xc0100000 - 0xc02a1e0c (1671 kB) [ 57.694526] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 57.778324] Calibrating delay using timer specific routine.. 3394.89 BogoMIPS (lpj=5655824) [ 57.778624] Security Framework v1.0.0 initialized [ 57.778705] SELinux: Disabled at boot. [ 57.778824] Mount-cache hash table entries: 512 [ 57.779471] CPU: After generic identify, caps: afe9fbbf 00000000 00000000 00000000 00000180 00000000 00000000 [ 57.779483] CPU: L1 I cache: 32K, L1 D cache: 32K [ 57.779590] CPU: L2 cache: 2048K [ 57.779665] CPU: After all inits, caps: afe9fbbf 00000000 00000000 00002040 00000180 00000000 00000000 [ 57.779672] Intel machine check architecture supported. [ 57.779754] Intel machine check reporting enabled on CPU#0. [ 57.779837] Compat vDSO mapped to ffffe000. [ 57.779923] CPU: Intel(R) Pentium(R) M processor 1.70GHz stepping 06 [ 57.780061] Checking 'hlt' instruction... OK. [ 57.791759] ACPI: Core revision 20070126 [ 57.801182] Parsing all Control Methods: [ 57.801363] Table [DSDT](id 0001) - 654 Objects with 50 Devices 163 Methods 17 Regions [ 57.801622] Parsing all Control Methods: [ 57.801761] Table [SSDT](id 0002) - 1 Objects with 0 Devices 1 Methods 0 Regions [ 57.802103] Parsing all Control Methods: [ 57.802243] Table [SSDT](id 0003) - 6 Objects with 0 Devices 3 Methods 0 Regions [ 57.802433] tbxface-0587 [02] tb_load_namespace : ACPI Tables successfully acquired [ 57.876949] evxfevnt-0091 [02] enable : Transition to ACPI mode successful [ 57.877622] ENABLING IO-APIC IRQs [ 57.877901] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 [ 58.015431] NET: Registered protocol family 16 [ 58.016104] ACPI: bus type pci registered [ 58.017441] PCI: PCI BIOS revision 2.10 entry at 0xfd9c2, last bus=2 [ 58.017523] PCI: Using configuration type 1 [ 58.017599] Setting up standard PCI resources [ 58.038873] evgpeblk-0952 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 [ 58.043249] evgpeblk-1049 [03] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 0 Runtime GPEs in this block [ 58.045984] Completing Region/Field/Buffer/Package initialization:..................................................... [ 58.066979] Initialized 17/17 Regions 0/0 Fields 22/22 Buffers 14/23 Packages (670 nodes) [ 58.067181] Initializing Device/Processor/Thermal objects by executing _INI methods:. [ 58.068782] Executed 1 _INI methods requiring 0 _STA executions (examined 54 objects) [ 58.069405] ACPI: Interpreter enabled [ 58.069491] ACPI: (supports S0 S3 S4 S5) [ 58.070114] ACPI: Using IOAPIC for interrupt routing [ 60.181724] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 60.182937] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO [ 60.183021] PCI quirk: region 1180-11bf claimed by ICH4 GPIO [ 60.183189] 0000:00:1f.1: trying to change BAR0 from 0000 to 01F0 [ 60.183272] 0000:00:1f.1: trying to change BAR1 from 0000 to 03F4 [ 60.183355] 0000:00:1f.1: trying to change BAR2 from 0000 to 0170 [ 60.183438] 0000:00:1f.1: trying to change BAR3 from 0000 to 0374 [ 60.184541] PCI: Transparent bridge - 0000:00:1e.0 [ 60.184927] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 60.185741] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] [ 60.203605] ACPI: PCI Interrupt Link [LNKA] (IRQs *10) [ 60.204097] ACPI: PCI Interrupt Link [LNKB] (IRQs *5) [ 60.204582] ACPI: PCI Interrupt Link [LNKC] (IRQs *4) [ 60.205113] ACPI: PCI Interrupt Link [LNKD] (IRQs *3) [ 60.205613] ACPI: PCI Interrupt Link [LNKE] (IRQs *11) [ 60.206099] ACPI: PCI Interrupt Link [LNKF] (IRQs 3) *0, disabled. [ 60.206643] ACPI: PCI Interrupt Link [LNKG] (IRQs *4) [ 60.207127] ACPI: PCI Interrupt Link [LNKH] (IRQs *3) [ 60.207663] Linux Plug and Play Support v0.97 (c) Adam Belay [ 60.207789] pnp: PnP ACPI init [ 61.209150] [ACPI Debug] String: [0x1C] "Temperature increasing: _Q80" [ 61.212569] pnp: PnP ACPI: found 7 devices [ 61.215195] PCI: Using ACPI for IRQ routing [ 61.215272] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 61.221489] pnp: 00:04: iomem range 0xfec10000-0xfec1ffff has been reserved [ 61.223047] Time: tsc clocksource has been installed. [ 61.254320] PCI: Bus 2, cardbus bridge: 0000:01:09.0 [ 61.254399] IO window: 00003400-000034ff [ 61.254478] IO window: 00003800-000038ff [ 61.254558] PREFETCH window: 50000000-53ffffff [ 61.254639] MEM window: 58000000-5bffffff [ 61.254718] PCI: Bridge: 0000:00:1e.0 [ 61.254795] IO window: 3000-3fff [ 61.254875] MEM window: e0200000-e02fffff [ 61.254955] PREFETCH window: 50000000-53ffffff [ 61.255047] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 61.255069] ACPI: PCI Interrupt 0000:01:09.0[A] -> GSI 20 (level, low) -> IRQ 20 [ 61.255275] NET: Registered protocol family 2 [ 61.286400] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 61.286930] TCP established hash table entries: 65536 (order: 9, 2883584 bytes) [ 61.294850] TCP bind hash table entries: 65536 (order: 9, 2883584 bytes) [ 61.304630] TCP: Hash tables configured (established 65536 bind 65536) [ 61.304775] TCP reno registered [ 61.314210] Unpacking initramfs... done [ 61.540219] Freeing initrd memory: 3143k freed [ 61.540720] Simple Boot Flag at 0x36 set to 0x1 [ 61.542835] audit: initializing netlink socket (disabled) [ 61.542981] audit(1175081081.359:1): initialized [ 61.543489] highmem bounce pool size: 64 pages [ 61.543977] VFS: Disk quotas dquot_6.5.1 [ 61.544069] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 61.544412] io scheduler noop registered [ 61.544508] io scheduler cfq registered (default) [ 61.544613] Boot video device is 0000:00:02.0 [ 61.567170] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 61.569794] ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 17 [ 61.569955] ACPI: PCI interrupt for device 0000:00:1f.6 disabled [ 61.571055] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PSM1] at 0x60,0x64 irq 1,12 [ 61.573460] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 61.573548] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 61.574073] mice: PS/2 mouse device common for all mice [ 61.574704] async_tx: api initialized (async) [ 61.574782] xor: automatically using best checksumming function: pIII_sse [ 61.589151] pIII_sse : 4524.000 MB/sec [ 61.589228] xor: using function: pIII_sse (4524.000 MB/sec) [ 61.589461] TCP cubic registered [ 61.589564] NET: Registered protocol family 1 [ 61.589651] Using IPI Shortcut mode [ 61.590694] Freeing unused kernel memory: 176k freed [ 61.590865] Write protecting the kernel read-only data: 676k [ 61.623774] input: AT Translated Set 2 keyboard as /class/input/input0 [ 61.705748] [ACPI Debug] String: [0x1C] "Temperature increasing: _Q80" [ 61.755589] Switched to high resolution mode on CPU 0 [ 63.010750] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) [ 63.510190] [ACPI Debug] String: [0x11] "Current temp is: " [ 63.510212] [ACPI Debug] Integer: 0x00000040 [ 64.009511] [ACPI Debug] String: [0x11] "Current temp is: " [ 64.009531] [ACPI Debug] Integer: 0x00000040 [ 64.009641] ACPI: Thermal Zone [THRM] (64 C) [ 64.332671] usbcore: registered new interface driver usbfs [ 64.332794] usbcore: registered new interface driver hub [ 64.333180] usbcore: registered new device driver usb [ 64.334334] USB Universal Host Controller Interface driver v3.0 [ 64.334483] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 64.334507] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 64.334512] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 64.334889] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 64.334939] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001820 [ 64.335109] usb usb1: new device found, idVendor=0000, idProduct=0000 [ 64.335112] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 64.335116] usb usb1: Product: UHCI Host Controller [ 64.335118] usb usb1: Manufacturer: Linux 2.6.21-rc5-mm2 uhci_hcd [ 64.335121] usb usb1: SerialNumber: 0000:00:1d.0 [ 64.335545] usb usb1: configuration #1 chosen from 1 choice [ 64.335694] hub 1-0:1.0: USB hub found [ 64.335812] hub 1-0:1.0: 2 ports detected [ 64.343404] 8139too Fast Ethernet driver 0.9.28 [ 64.353232] ieee1394: Initialized config rom entry `ip1394' [ 64.401839] SCSI subsystem initialized [ 64.407421] libata version 2.20 loaded. [ 64.439323] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 64.439351] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 64.439356] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 64.439482] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 64.439536] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840 [ 64.439707] usb usb2: new device found, idVendor=0000, idProduct=0000 [ 64.439711] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 64.439714] usb usb2: Product: UHCI Host Controller [ 64.439716] usb usb2: Manufacturer: Linux 2.6.21-rc5-mm2 uhci_hcd [ 64.439719] usb usb2: SerialNumber: 0000:00:1d.1 [ 64.440075] usb usb2: configuration #1 chosen from 1 choice [ 64.440214] hub 2-0:1.0: USB hub found [ 64.440236] hub 2-0:1.0: 2 ports detected [ 64.547839] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 64.547865] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 64.547870] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 64.548007] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 64.548064] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860 [ 64.548211] usb usb3: new device found, idVendor=0000, idProduct=0000 [ 64.548214] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 64.548218] usb usb3: Product: UHCI Host Controller [ 64.548220] usb usb3: Manufacturer: Linux 2.6.21-rc5-mm2 uhci_hcd [ 64.548222] usb usb3: SerialNumber: 0000:00:1d.2 [ 64.548543] usb usb3: configuration #1 chosen from 1 choice [ 64.548684] hub 3-0:1.0: USB hub found [ 64.548706] hub 3-0:1.0: 2 ports detected [ 64.649153] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23 [ 64.649179] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 64.649184] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 64.649305] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 [ 64.649405] ehci_hcd 0000:00:1d.7: debug port 1 [ 64.649413] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 64.649431] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0100000 [ 64.653321] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 64.653410] usb usb4: new device found, idVendor=0000, idProduct=0000 [ 64.653413] usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 64.653416] usb usb4: Product: EHCI Host Controller [ 64.653418] usb usb4: Manufacturer: Linux 2.6.21-rc5-mm2 ehci_hcd [ 64.653420] usb usb4: SerialNumber: 0000:00:1d.7 [ 64.653769] usb usb4: configuration #1 chosen from 1 choice [ 64.653921] hub 4-0:1.0: USB hub found [ 64.653987] hub 4-0:1.0: 6 ports detected [ 64.756012] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 64.756623] eth0: RealTek RTL8139 at 0xf884a800, 00:c0:9f:95:18:1b, IRQ 16 [ 64.756626] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 64.756813] ACPI: PCI Interrupt 0000:01:09.2[C] -> GSI 22 (level, low) -> IRQ 22 [ 64.824200] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22] MMIO=[e0207000-e02077ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 64.824408] ata_piix 0000:00:1f.1: version 2.10ac1 [ 64.824431] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) [ 64.824441] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18 [ 64.824481] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 64.826262] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011810 irq 14 [ 64.826500] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011818 irq 15 [ 64.826541] scsi0 : ata_piix [ 64.985031] ata1.00: ATA-6: FUJITSU MHU2100AT, 00000008, max UDMA/100 [ 64.985035] ata1.00: 195371568 sectors, multi 16: LBA [ 64.991676] ata1.00: configured for UDMA/100 [ 64.991687] scsi1 : ata_piix [ 65.304593] ata2.00: ATAPI, max UDMA/33 [ 65.464372] ata2.00: configured for UDMA/33 [ 65.464829] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHU2100A 0000 PQ: 0 ANSI: 5 [ 65.470205] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GMA-4080N 0S35 PQ: 0 ANSI: 5 [ 65.499844] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 65.499966] sd 0:0:0:0: [sda] Write Protect is off [ 65.500045] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 65.500099] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 65.500431] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 65.500540] sd 0:0:0:0: [sda] Write Protect is off [ 65.500619] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 65.500674] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 65.500835] sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 > [ 66.025799] sd 0:0:0:0: [sda] Attached SCSI disk [ 66.036659] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 66.041191] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 66.074746] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 66.074878] Uniform CD-ROM driver Revision: 3.20 [ 66.075191] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 66.093784] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f00004fec18] [ 66.930058] Attempting manual resume [ 66.957700] EXT3-fs: INFO: recovery required on readonly filesystem. [ 66.957788] EXT3-fs: write access will be enabled during recovery. [ 70.600696] [ACPI Debug] String: [0x1C] "Temperature increasing: _Q80" [ 71.099947] [ACPI Debug] String: [0x11] "Current temp is: " [ 71.100101] [ACPI Debug] Integer: 0x0000003B [ 71.599282] [ACPI Debug] String: [0x1C] "Temperature increasing: _Q80" [ 72.098616] [ACPI Debug] String: [0x11] "Current temp is: " [ 72.098777] [ACPI Debug] Integer: 0x0000003B [ 73.220486] kjournald starting. Commit interval 5 seconds [ 73.595518] EXT3-fs: mounted filesystem with ordered data mode. [ 91.722734] IPv4 FIB: Using LC-trie version 0.407 [ 92.953555] Linux agpgart interface v0.102 (c) Dave Jones [ 93.050389] agpgart: Detected an Intel 855 Chipset. [ 93.051364] agpgart: Detected 32636K stolen memory. [ 93.062734] agpgart: AGP aperture is 128M @ 0xe8000000 [ 93.151484] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 93.176187] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 93.190053] iTCO_vendor_support: vendor-support=0 [ 93.191528] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007) [ 93.191946] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060) [ 93.192230] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 93.316838] Real Time Clock Driver v1.12ac [ 93.363658] intel_rng: FWH not detected [ 93.396467] ieee80211_crypt: registered algorithm 'NULL' [ 93.412614] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 93.412703] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> [ 93.453208] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kdmprq [ 93.453338] ipw2200: Copyright(c) 2003-2006 Intel Corporation [ 93.454065] ACPI: PCI Interrupt 0000:01:06.0[A] -> GSI 18 (level, low) -> IRQ 18 [ 93.485935] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection [ 93.639978] sdhci: Secure Digital Host Controller Interface driver [ 93.640070] sdhci: Copyright(c) Pierre Ossman [ 93.912114] Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0 [ 93.943409] input: SynPS/2 Synaptics TouchPad as /class/input/input1 [ 94.396392] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels) [ 94.396769] Yenta: CardBus bridge found at 0000:01:09.0 [103c:3080] [ 94.396869] Yenta: Enabling burst memory read transactions [ 94.396951] Yenta: Using CSCINT to route CSC interrupts to PCI [ 94.397030] Yenta: Routing CardBus interrupts to PCI [ 94.397112] Yenta TI: socket 0000:01:09.0, mfunc 0x01a01b22, devctl 0x64 [ 94.625731] Yenta: ISA IRQ mask 0x0cf8, PCI irq 20 [ 94.625816] Socket status: 30000006 [ 94.625900] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff [ 94.626005] pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe02fffff [ 94.626089] pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff [ 94.630308] ACPI: PCI Interrupt 0000:01:09.3[A] -> GSI 20 (level, low) -> IRQ 20 [ 94.648973] sdhci: SDHCI controller found at 0000:01:09.4 [104c:8034] (rev 0) [ 94.649083] ACPI: PCI Interrupt 0000:01:09.4[A] -> GSI 20 (level, low) -> IRQ 20 [ 94.649524] mmc0: SDHCI at 0xe0208400 irq 20 DMA [ 94.649745] mmc1: SDHCI at 0xe0208000 irq 20 DMA [ 94.649981] mmc2: SDHCI at 0xe0207c00 irq 20 DMA [ 94.650192] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17 [ 94.650389] PCI: Setting latency timer of device 0000:00:1f.5 to 64 [ 94.964469] intel8x0_measure_ac97_clock: measured 50171 usecs [ 94.964556] intel8x0: clocking to 48000 [ 95.251403] lp: driver loaded but no devices found [ 95.348575] fuse init (API version 7.8) [ 95.404135] Adding 1052216k swap on /dev/disk/by-uuid/f5d0cec6-779a-4035-bb7b-9a0837ac3e66. Priority:-1 extents:1 across:1052216k [ 95.711279] EXT3 FS on sda11, internal journal [ 117.771965] kjournald starting. Commit interval 5 seconds [ 117.772356] EXT3 FS on sda10, internal journal [ 117.772366] EXT3-fs: mounted filesystem with ordered data mode. [ 117.996602] kjournald starting. Commit interval 5 seconds [ 118.000404] EXT3 FS on sda6, internal journal [ 118.000414] EXT3-fs: mounted filesystem with ordered data mode. [ 118.028237] kjournald starting. Commit interval 5 seconds [ 118.028711] EXT3 FS on sda7, internal journal [ 118.028719] EXT3-fs: mounted filesystem with ordered data mode. [ 118.032497] kjournald starting. Commit interval 5 seconds [ 118.032897] EXT3 FS on sda9, internal journal [ 118.032905] EXT3-fs: mounted filesystem with ordered data mode. [ 122.294327] ACPI: AC Adapter [ACAD] (on-line) [ 124.381468] ACPI: Battery Slot [BAT0] (battery present) [ 124.401835] input: Power Button (FF) as /class/input/input2 [ 124.402332] ACPI: Power Button (FF) [PWRF] [ 124.404691] input: Lid Switch as /class/input/input3 [ 124.404790] ACPI: Lid Switch [LID0] [ 124.404993] input: Sleep Button (CM) as /class/input/input4 [ 124.405084] ACPI: Sleep Button (CM) [SLPB] [ 126.529386] No dock devices found. [ 126.585634] toshiba_acpi: Unknown parameter `hotkeys_over_acpi' [ 126.606239] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no) [ 130.847807] Capability LSM initialized [ 130.891859] eth0: link down [ 133.317897] [drm] Initialized drm 1.1.0 20060810 [ 133.323604] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 133.326885] [drm] Initialized i915 1.6.0 20060119 on minor 0 [ 133.330064] [drm] Initialized i915 1.6.0 20060119 on minor 1 [ 134.373854] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 77.413325] Marking TSC unstable due to: cpufreq changes. [ 77.416658] Time: acpi_pm clocksource has been installed. [ 77.889992] Clocksource tsc unstable (delta = -312378109 ns) [ 108.756655] NET: Registered protocol family 10 [ 108.756655] lo: Disabled Privacy Extensions [ 108.756655] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 118.973321] eth1: no IPv6 routers present
00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at <unassigned> (32-bit, prefetchable) Capabilities: [40] Vendor Specific Information
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02) (prog-if 00 [VGA]) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=512K] Region 2: I/O ports at 1800 [size=8] Capabilities: [d0] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [disabled] [size=128M] Region 1: Memory at e0080000 (32-bit, non-prefetchable) [disabled] [size=512K] Capabilities: [d0] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at 1820 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 1840 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 1860 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 23 Region 0: Memory at e0100000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 0 Bus: primary=00, secondary=01, subordinate=05, sec-latency=64 I/O behind bridge: 00003000-00003fff Memory behind bridge: e0200000-e02fffff Prefetchable memory behind bridge: 50000000-53ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at 1810 [size=16] Region 5: Memory at 54000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 5 Region 4: I/O ports at 1880 [size=32]
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at 1c00 [size=256] Region 1: I/O ports at 18c0 [size=64] Region 2: Memory at e0100c00 (32-bit, non-prefetchable) [size=512] Region 3: Memory at e0100800 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03) (prog-if 00 [Generic]) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at 2400 [size=256] Region 1: I/O ports at 2000 [size=128] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME+
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 3000 [size=256] Region 1: Memory at e0207800 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:06.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05) Subsystem: Hewlett-Packard Company Unknown device 12f5 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (750ns min, 6000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at e0206000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME-
01:09.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size: 128 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at e0209000 (32-bit, non-prefetchable) [size=4K] Bus: primary=01, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 50000000-53fff000 (prefetchable) Memory window 1: 58000000-5bfff000 I/O window 0: 00003400-000034ff I/O window 1: 00003800-000038ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001
01:09.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (750ns min, 1000ns max), Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 22 Region 0: Memory at e0207000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at e0200000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+
01:09.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at e0204000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:09.4 Generic system peripheral [0805]: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller Subsystem: Hewlett-Packard Company Unknown device 3080 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at e0208400 (32-bit, non-prefetchable) [size=256] Region 1: Memory at e0208000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at e0207c00 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |