Messages in this thread |  | | Date | Wed, 7 Feb 2007 20:10:05 +0800 | From | "Luming Yu" <> | Subject | Re: hwsusp defunct |
| |
For acpi issues, please enter bug into bugzilla.kernel.org with dmesg, acpidump output .
On 2/7/07, Jiri Slaby <jirislaby@gmail.com> wrote: > Cc: linux-acpi > not-cc: linux-pm > > Rafael J. Wysocki napsal(a): > > On Tuesday, 6 February 2007 12:18, Jiri Slaby wrote: > >> This is blindly written dmesg after resume. See it whole at [2]: > >> Suspending device 0.0 > >> ACPI Exception (exoparg2-0442): AE_AML_PACKAGE_LIMIT, Index (000000007) is beyon > >> d end of object [20070126] > >> ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.GTM_] > >> (Node dfe64fcc), AE_AML_PACKAGE_LIMIT > >> ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN0._ > >> GTM] (Node dfe649f0), AE_AML_PACKAGE_LIMIT > >> ... > >> hda: selected mode 0x45 > >> ACPI Error (dsopcode-0481): Attempt to CreateField of length zero [20070126] > >> ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] > >> (Node dfe64ec8), AE_AML_OPERAND_VALUE > >> ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN0.D > >> RV1._GTF] (Node dfe64964), AE_AML_OPERAND_VALUE > >> do_drive_get_GTF: Run _GTF error: status = 0x3006 > > > > This looks like an ACPI-vs-IDE problem. You can try to use libata drivers instead > > of the "old IDE" ones. > > > >> $ ls -l /sys/block/hda/device > >> lrwxrwxrwx 1 root root 0 úno 6 12:14 /sys/block/hda/device -> > >> ../../devices/pci0000:00/0000:00:1f.1/ide0/0.0 > >> $ ls -l /sys/block/hda/device/driver > >> lrwxrwxrwx 1 root root 0 úno 6 12:15 /sys/block/hda/device/driver -> > >> ../../../../../bus/ide/drivers/ide-disk > >> $ ls -l /sys/block/hda/device/driver/0.0 > >> lrwxrwxrwx 1 root root 0 úno 6 12:16 /sys/block/hda/device/driver/0.0 -> > >> ../../../../devices/pci0000:00/0000:00:1f.1/ide0/0.0 > >> # lspci -vvvxxs 0000:00:1f.1 > >> 00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller > >> (rev 02) (prog-if 8a [Master SecP PriP]) > >> Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard > >> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > >> Stepping- SERR- FastB2B- > >> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > >> <TAbort- <MAbort- >SERR- <PERR- > >> Latency: 0 > >> Interrupt: pin A routed to IRQ 5 > >> Region 0: I/O ports at 01f0 [size=8] > >> Region 1: I/O ports at 03f4 [size=1] > >> Region 2: I/O ports at 0170 [size=8] > >> Region 3: I/O ports at 0374 [size=1] > >> Region 4: I/O ports at fc00 [size=16] > >> Region 5: Memory at 30100000 (32-bit, non-prefetchable) [size=1K] > >> 00: 86 80 db 24 07 00 80 02 02 8a 01 01 00 00 00 00 > >> 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00 > >> 20: 01 fc 00 00 00 00 10 30 00 00 00 00 43 10 a6 80 > >> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 > >> > >> Do you want acpidump? > > > > I'm not an ACPI expert, it won't tell me a lot, but perhaps you should add > > linux-acpi to the Cc list. ;-) > [...] > > [1] > > http://www.fi.muni.cz/~xslaby/sklad/config-mm > > [2] > > http://www.fi.muni.cz/~xpapiez/test/dmesg-mm.txt > > Ok, acpi folks, any suggests? > > thanks, > -- > http://www.fi.muni.cz/~xslaby/ Jiri Slaby > faculty of informatics, masaryk university, brno, cz > e-mail: jirislaby gmail com, gpg pubkey fingerprint: > B674 9967 0407 CE62 ACC8 22A0 32CC 55C3 39D4 7A7E > - > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ > - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
|  |