lkml.org 
[lkml]   [2007]   [Feb]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[git patches] libata updates (mostly fixes)

The pile that was waiting for post-conference, largely bug fixes.

As mentioned in the last push, were two other push points planned for
2.6.21:
1) merge libata support for ACPI
2) Remove ugly combined mode hacks in libata-sff and pci/quirks, now
that old-IDE and libata have the necessary improvements.

Depending on timing and the devres bug count, I may push #2 back to
2.6.22. The sum of devres + ACPI + remove-combined-mode-quirks
might be more change than should be in 2.6.21.

Both ACPI and remove-combined-quirks are ready to be pushed, it's just a
matter of staging. Comments welcome.

Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus

to receive the following updates:

arch/ia64/Kconfig | 1 +
drivers/ata/libata-core.c | 11 ++++++-
drivers/ata/pata_legacy.c | 11 +++++-
drivers/ata/pata_qdi.c | 4 ++-
drivers/ata/pata_sl82c105.c | 3 ++
drivers/ata/sata_nv.c | 6 +++-
drivers/ata/sata_promise.c | 64 +++++++------------------------------
drivers/ata/sata_vsc.c | 8 +++-
include/asm-ia64/libata-portmap.h | 12 +++++++
include/linux/ata.h | 2 +-
include/linux/libata.h | 1 +
11 files changed, 63 insertions(+), 60 deletions(-)
create mode 100644 include/asm-ia64/libata-portmap.h

Alan Cox (1):
libata: Add a host flag to indicate lack of IORDY capability

Mikael Pettersson (2):
sata_promise: fix missing PATA cable detection
sata_promise: new EH conversion for 20619 chips, take 2

Nate Dailey (1):
sata_vsc: use default cache line size if non-zero

Olaf Hering (1):
add delay around sl82c105_reset_engine calls

Robert Hancock (1):
sata_nv: handle SError status indication

Tejun Heo (2):
libata: fix drive side 80c cable check, take 3
libata: clear TF before IDENTIFYing

Zhang, Yanmin (1):
ATA convert GSI to irq on ia64

diff --git a/arch/ia64/Kconfig b/arch/ia64/Kconfig
index db185f3..d51f0f1 100644
--- a/arch/ia64/Kconfig
+++ b/arch/ia64/Kconfig
@@ -22,6 +22,7 @@ config IA64

config 64BIT
bool
+ select ATA_NONSTANDARD if ATA
default y

config ZONE_DMA
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 25d8d3f..2cf8251 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1410,7 +1410,16 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
}

tf.protocol = ATA_PROT_PIO;
- tf.flags |= ATA_TFLAG_POLLING; /* for polling presence detection */
+
+ /* Some devices choke if TF registers contain garbage. Make
+ * sure those are properly initialized.
+ */
+ tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
+
+ /* Device presence detection is unreliable on some
+ * controllers. Always poll IDENTIFY if available.
+ */
+ tf.flags |= ATA_TFLAG_POLLING;

err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE,
id, sizeof(id[0]) * ATA_ID_WORDS);
diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c
index 4223e10..98c1fee 100644
--- a/drivers/ata/pata_legacy.c
+++ b/drivers/ata/pata_legacy.c
@@ -89,9 +89,10 @@ static int probe_all; /* Set to check all ISA port ranges */
static int ht6560a; /* HT 6560A on primary 1, secondary 2, both 3 */
static int ht6560b; /* HT 6560A on primary 1, secondary 2, both 3 */
static int opti82c611a; /* Opti82c611A on primary 1, secondary 2, both 3 */
-static int opti82c46x; /* Opti 82c465MV present (pri/sec autodetect) */
+static int opti82c46x; /* Opti 82c465MV present (pri/sec autodetect) */
static int autospeed; /* Chip present which snoops speed changes */
static int pio_mask = 0x1F; /* PIO range for autospeed devices */
+static int iordy_mask = 0xFFFFFFFF; /* Use iordy if available */

/**
* legacy_set_mode - mode setting
@@ -113,6 +114,7 @@ static int legacy_set_mode(struct ata_port *ap, struct ata_device **unused)
for (i = 0; i < ATA_MAX_DEVICES; i++) {
struct ata_device *dev = &ap->device[i];
if (ata_dev_enabled(dev)) {
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO\n");
dev->pio_mode = XFER_PIO_0;
dev->xfer_mode = XFER_PIO_0;
dev->xfer_shift = ATA_SHIFT_PIO;
@@ -695,6 +697,7 @@ static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl
void __iomem *io_addr, *ctrl_addr;
int pio_modes = pio_mask;
u32 mask = (1 << port);
+ u32 iordy = (iordy_mask & mask) ? 0: ATA_FLAG_NO_IORDY;
int ret;

pdev = platform_device_register_simple(DRV_NAME, nr_legacy_host, NULL, 0);
@@ -715,6 +718,7 @@ static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl
if (ht6560a & mask) {
ops = &ht6560a_port_ops;
pio_modes = 0x07;
+ iordy = ATA_FLAG_NO_IORDY;
}
if (ht6560b & mask) {
ops = &ht6560b_port_ops;
@@ -750,6 +754,7 @@ static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl
printk(KERN_INFO "PDC20230-C/20630 VLB ATA controller detected.\n");
pio_modes = 0x07;
ops = &pdc20230_port_ops;
+ iordy = ATA_FLAG_NO_IORDY;
udelay(100);
inb(0x1F5);
} else {
@@ -767,6 +772,7 @@ static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl
/* Chip does mode setting by command snooping */
if (ops == &legacy_port_ops && (autospeed & mask))
ops = &simple_port_ops;
+
memset(&ae, 0, sizeof(struct ata_probe_ent));
INIT_LIST_HEAD(&ae.node);
ae.dev = &pdev->dev;
@@ -776,7 +782,7 @@ static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl
ae.pio_mask = pio_modes;
ae.irq = irq;
ae.irq_flags = 0;
- ae.port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST;
+ ae.port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST|iordy;
ae.port[0].cmd_addr = io_addr;
ae.port[0].altstatus_addr = ctrl_addr;
ae.port[0].ctl_addr = ctrl_addr;
@@ -945,6 +951,7 @@ module_param(ht6560b, int, 0);
module_param(opti82c611a, int, 0);
module_param(opti82c46x, int, 0);
module_param(pio_mask, int, 0);
+module_param(iordy_mask, int, 0);

module_init(legacy_init);
module_exit(legacy_exit);
diff --git a/drivers/ata/pata_qdi.c b/drivers/ata/pata_qdi.c
index 1b3b4ed..4362141 100644
--- a/drivers/ata/pata_qdi.c
+++ b/drivers/ata/pata_qdi.c
@@ -264,16 +264,18 @@ static __init int qdi_init_one(unsigned long port, int type, unsigned long io, i
if (type == 6580) {
ae.port_ops = &qdi6580_port_ops;
ae.pio_mask = 0x1F;
+ ae.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST;
} else {
ae.port_ops = &qdi6500_port_ops;
ae.pio_mask = 0x07; /* Actually PIO3 !IORDY is possible */
+ ae.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST |
+ ATA_FLAG_NO_IORDY;
}

ae.sht = &qdi_sht;
ae.n_ports = 1;
ae.irq = irq;
ae.irq_flags = 0;
- ae.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST;
ae.port[0].cmd_addr = io_addr;
ae.port[0].altstatus_addr = ctl_addr;
ae.port[0].ctl_addr = ctl_addr;
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index f2fa158..96e890f 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -187,7 +187,9 @@ static void sl82c105_bmdma_start(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;

+ udelay(100);
sl82c105_reset_engine(ap);
+ udelay(100);

/* Set the clocks for DMA */
sl82c105_configure_dmamode(ap, qc->dev);
@@ -216,6 +218,7 @@ static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc)

ata_bmdma_stop(qc);
sl82c105_reset_engine(ap);
+ udelay(100);

/* This will redo the initial setup of the DMA device to matching
PIO timings */
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 095ef1b..ab92f20 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -827,7 +827,8 @@ static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
/* freeze if hotplugged or controller error */
if (unlikely(status & (NV_ADMA_STAT_HOTPLUG |
NV_ADMA_STAT_HOTUNPLUG |
- NV_ADMA_STAT_TIMEOUT))) {
+ NV_ADMA_STAT_TIMEOUT |
+ NV_ADMA_STAT_SERROR))) {
struct ata_eh_info *ehi = &ap->eh_info;

ata_ehi_clear_desc(ehi);
@@ -841,6 +842,9 @@ static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
} else if (status & NV_ADMA_STAT_HOTUNPLUG) {
ata_ehi_hotplugged(ehi);
ata_ehi_push_desc(ehi, ": hot unplug");
+ } else if (status & NV_ADMA_STAT_SERROR) {
+ /* let libata analyze SError and figure out the cause */
+ ata_ehi_push_desc(ehi, ": SError");
}
ata_port_freeze(ap);
continue;
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index b2e2e69..cf9ed8c 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -119,9 +119,7 @@ static u32 pdc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void pdc_sata_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static irqreturn_t pdc_interrupt (int irq, void *dev_instance);
-static void pdc_eng_timeout(struct ata_port *ap);
static int pdc_port_start(struct ata_port *ap);
-static void pdc_pata_phy_reset(struct ata_port *ap);
static void pdc_qc_prep(struct ata_queued_cmd *qc);
static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf);
static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf);
@@ -215,12 +213,12 @@ static const struct ata_port_operations pdc_pata_ops = {
.dev_select = ata_std_dev_select,
.check_atapi_dma = pdc_check_atapi_dma,

- .phy_reset = pdc_pata_phy_reset,
-
.qc_prep = pdc_qc_prep,
.qc_issue = pdc_qc_issue_prot,
+ .freeze = pdc_freeze,
+ .thaw = pdc_thaw,
+ .error_handler = pdc_error_handler,
.data_xfer = ata_data_xfer,
- .eng_timeout = pdc_eng_timeout,
.irq_handler = pdc_interrupt,
.irq_clear = pdc_irq_clear,
.irq_on = ata_irq_on,
@@ -253,7 +251,7 @@ static const struct ata_port_info pdc_port_info[] = {
/* board_20619 */
{
.sht = &pdc_ata_sht,
- .flags = PDC_COMMON_FLAGS | ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS,
+ .flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = 0x7f, /* udma0-6 ; FIXME */
@@ -389,14 +387,6 @@ static void pdc_pata_cbl_detect(struct ata_port *ap)
ap->cbl = ATA_CBL_PATA80;
}

-static void pdc_pata_phy_reset(struct ata_port *ap)
-{
- pdc_pata_cbl_detect(ap);
- pdc_reset_port(ap);
- ata_port_probe(ap);
- ata_bus_reset(ap);
-}
-
static u32 pdc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
if (sc_reg > SCR_CONTROL || ap->cbl != ATA_CBL_SATA)
@@ -564,6 +554,13 @@ static void pdc_thaw(struct ata_port *ap)
readl(mmio + PDC_CTLSTAT); /* flush */
}

+static int pdc_pre_reset(struct ata_port *ap)
+{
+ if (!sata_scr_valid(ap))
+ pdc_pata_cbl_detect(ap);
+ return ata_std_prereset(ap);
+}
+
static void pdc_error_handler(struct ata_port *ap)
{
ata_reset_fn_t hardreset;
@@ -576,7 +573,7 @@ static void pdc_error_handler(struct ata_port *ap)
hardreset = sata_std_hardreset;

/* perform recovery */
- ata_do_eh(ap, ata_std_prereset, ata_std_softreset, hardreset,
+ ata_do_eh(ap, pdc_pre_reset, ata_std_softreset, hardreset,
ata_std_postreset);
}

@@ -592,43 +589,6 @@ static void pdc_post_internal_cmd(struct ata_queued_cmd *qc)
pdc_reset_port(ap);
}

-static void pdc_eng_timeout(struct ata_port *ap)
-{
- struct ata_host *host = ap->host;
- u8 drv_stat;
- struct ata_queued_cmd *qc;
- unsigned long flags;
-
- DPRINTK("ENTER\n");
-
- spin_lock_irqsave(&host->lock, flags);
-
- qc = ata_qc_from_tag(ap, ap->active_tag);
-
- switch (qc->tf.protocol) {
- case ATA_PROT_DMA:
- case ATA_PROT_NODATA:
- ata_port_printk(ap, KERN_ERR, "command timeout\n");
- drv_stat = ata_wait_idle(ap);
- qc->err_mask |= __ac_err_mask(drv_stat);
- break;
-
- default:
- drv_stat = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000);
-
- ata_port_printk(ap, KERN_ERR,
- "unknown timeout, cmd 0x%x stat 0x%x\n",
- qc->tf.command, drv_stat);
-
- qc->err_mask |= ac_err_mask(drv_stat);
- break;
- }
-
- spin_unlock_irqrestore(&host->lock, flags);
- ata_eh_qc_complete(qc);
- DPRINTK("EXIT\n");
-}
-
static inline unsigned int pdc_host_intr( struct ata_port *ap,
struct ata_queued_cmd *qc)
{
diff --git a/drivers/ata/sata_vsc.c b/drivers/ata/sata_vsc.c
index 3d9daf2..2fd037b 100644
--- a/drivers/ata/sata_vsc.c
+++ b/drivers/ata/sata_vsc.c
@@ -346,6 +346,7 @@ static int __devinit vsc_sata_init_one (struct pci_dev *pdev, const struct pci_d
struct ata_probe_ent *probe_ent;
void __iomem *mmio_base;
int rc;
+ u8 cls;

if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
@@ -383,9 +384,12 @@ static int __devinit vsc_sata_init_one (struct pci_dev *pdev, const struct pci_d
INIT_LIST_HEAD(&probe_ent->node);

/*
- * Due to a bug in the chip, the default cache line size can't be used
+ * Due to a bug in the chip, the default cache line size can't be
+ * used (unless the default is non-zero).
*/
- pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 0x80);
+ pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &cls);
+ if (cls == 0x00)
+ pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 0x80);

if (pci_enable_msi(pdev) == 0)
pci_intx(pdev, 0);
diff --git a/include/asm-ia64/libata-portmap.h b/include/asm-ia64/libata-portmap.h
new file mode 100644
index 0000000..0e00c9a
--- /dev/null
+++ b/include/asm-ia64/libata-portmap.h
@@ -0,0 +1,12 @@
+#ifndef __ASM_IA64_LIBATA_PORTMAP_H
+#define __ASM_IA64_LIBATA_PORTMAP_H
+
+#define ATA_PRIMARY_CMD 0x1F0
+#define ATA_PRIMARY_CTL 0x3F6
+#define ATA_PRIMARY_IRQ(dev) isa_irq_to_vector(14)
+
+#define ATA_SECONDARY_CMD 0x170
+#define ATA_SECONDARY_CTL 0x376
+#define ATA_SECONDARY_IRQ(dev) isa_irq_to_vector(15)
+
+#endif
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 18e401f..272736e 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -352,7 +352,7 @@ static inline int ata_drive_40wire(const u16 *dev_id)
{
if (ata_id_major_version(dev_id) >= 5 && ata_id_is_sata(dev_id))
return 0; /* SATA */
- if (dev_id[93] & 0x4000)
+ if ((dev_id[93] & 0xE000) == 0x6000)
return 0; /* 80 wire */
return 1;
}
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 596e0c1..b870b20 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -172,6 +172,7 @@ enum {
ATA_FLAG_DEBUGMSG = (1 << 13),
ATA_FLAG_SETXFER_POLLING= (1 << 14), /* use polling for SETXFER */
ATA_FLAG_IGN_SIMPLEX = (1 << 15), /* ignore SIMPLEX */
+ ATA_FLAG_NO_IORDY = (1 << 16), /* controller lacks iordy */

/* The following flag belongs to ap->pflags but is kept in
* ap->flags because it's referenced in many LLDs and will be
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2007-02-16 00:37    [W:0.100 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site