lkml.org 
[lkml]   [2007]   [Nov]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: [linux-usb-devel] [BUG] USB_PERSIST
    Hi Alan,

    Here's what I got after compiling kernel with CONFIG_USB_PERSIST and
    CONFIG_USB_DEBUG both enabled. The attached files are:

    config - shows the .config file used when compiling kernel 2.6.23.9

    sysandmount.txt - shows mounts and the state of persist for all usb
    devices right before suspending.

    dmesg_attached.txt - dmesg right after resuming when the USB device
    remained attached while machine was suspend

    dmesg_detachedandreattached.txt - dmesg right after resuming when the
    USB device was detached while suspended and then reattached before
    resuming.

    Thanks,
    Raymano G.


    On 11/26/07, Alan Stern <stern@rowland.harvard.edu> wrote:
    > On Mon, 26 Nov 2007, Raymano Garibaldi wrote:
    >
    > > > Wait a minute. You're saying that USB Persist worked under 2.6.21
    > > > because it wasn't available? That makes no sense. Besides, if you
    > > > don't like USB Persist under 2.6.23, you can always eliminate it by
    > > > turning off CONFIG_USB_PERSIST.
    > > >
    > >
    > > I have tried this. Simply turning off CONFIG_USB_PERSIST doesn't work.
    > > In this case the USB drive file system is unmounted on resume, even if
    > > the drive remained plugged in during suspend.
    >
    > Something about this doesn't sound right.
    >
    > When you have CONFIG_USB_PERSIST enabled, do you remember to turn on
    > the Persist feature for the root fs device by writing a "1" to the
    > device's power/persist file in sysfs?
    >
    > Can you try building a kernel with CONFIG_USB_PERSIST and
    > CONFIG_USB_DEBUG both enabled, and post the dmesg log from immediately
    > after resuming?
    >
    > Alan Stern
    >
    >
    [unhandled content-type:application/octet-stream][root@myfaun sys]# find /sys -name "persist" -print
    /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-6/power/persist
    /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-7/power/persist
    /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/power/persist
    /sys/devices/pci0000:00/0000:00:1d.7/usb2/power/persist
    /sys/devices/pci0000:00/0000:00:1d.3/usb5/power/persist
    /sys/devices/pci0000:00/0000:00:1d.2/usb4/power/persist
    /sys/devices/pci0000:00/0000:00:1d.1/usb3/power/persist
    /sys/devices/pci0000:00/0000:00:1d.0/usb1/power/persist

    [root@myfaun guest]# find /sys -name "persist" -exec cat {} \;
    1
    1
    1
    1
    1
    1
    1
    1

    [root@myfaun sys]# mount
    /dev/sda3 on / type ext3 (rw,noatime)
    none on /proc type proc (rw)
    none on /sys type sysfs (rw)
    none on /dev type ramfs (rw)
    none on /proc/bus/usb type usbfs (rw)
    none on /dev/pts type devpts (rw)
    none on /dev/shm type tmpfs (rw)
    /dev/sdb1 on /media/disk type vfat (rw,nosuid,nodev,noatime,flush,uid=1000,utf8,shortname=lower)
    b_resume
    usb usb4: usb resume
    usb usb4: wakeup_rh
    hub 4-0:1.0: hub_resume
    usb usb5: usb resume
    usb usb5: wakeup_rh
    hub 5-0:1.0: hub_resume
    usb 2-6: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: finish resume
    Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
    done.
    hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
    usb usb3: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    usb usb5: suspend_rh (auto-stop)
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    usb usb1: suspend_rh
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 5-0:1.0: hub_suspend
    usb usb5: bus auto-suspend
    usb usb5: suspend_rh
    Stopping tasks ... done.
    Suspending console(s)
    usb 2-6: usb suspend
    sd 2:0:0:0: [sda] Synchronizing SCSI cache
    sd 2:0:0:0: [sda] Stopping disk
    usb 2-7: usb suspend
    usb 2-1: usb suspend
    hub 2-0:1.0: hub_suspend
    usb usb2: bus suspend
    ehci_hcd 0000:00:1d.7: suspend root hub
    ACPI handle has no context!
    ACPI handle has no context!
    ACPI: PCI interrupt for device 0000:00:1f.2 disabled
    ACPI: PCI interrupt for device 0000:00:1f.1 disabled
    ACPI: PCI interrupt for device 0000:00:1d.7 disabled
    ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
    uhci_hcd 0000:00:1d.3: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.3 disabled
    uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.2: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.2 disabled
    uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.1: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.1 disabled
    uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.0: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.0 disabled
    uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
    ACPI: PCI interrupt for device 0000:00:1b.0 disabled
    Disabling non-boot CPUs ...
    CPU 1 is now offline
    SMP alternatives: switching to UP code
    CPU1 is down
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU0: Thermal monitoring enabled
    Back to C!
    Enabling non-boot CPUs ...
    SMP alternatives: switching to SMP code
    Booting processor 1/1 eip 3000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 6004.36 BogoMIPS (lpj=10003787)
    CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
    monitor/mwait feature present.
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU1: Thermal monitoring enabled
    CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
    CPU1 is up
    ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
    Switched to high resolution mode on CPU 1
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
    PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
    PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
    PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
    PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    uhci_hcd 0000:00:1d.0: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: uhci_resume
    uhci_hcd 0000:00:1d.1: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: uhci_resume
    uhci_hcd 0000:00:1d.2: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: uhci_resume
    uhci_hcd 0000:00:1d.3: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: uhci_resume
    ehci_hcd 0000:00:1d.7: resume from PCI D3
    PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
    PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1f.1 to 64
    ata2: port disabled. ignoring.
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    pnp: Failed to activate device 00:07.
    pnp: Failed to activate device 00:08.
    e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
    ata4: SATA link down (SStatus 0 SControl 300)
    ata5: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    ata1.00: configured for UDMA/33
    usb usb1: usb resume
    usb usb1: wakeup_rh
    hub 1-0:1.0: hub_resume
    usb usb2: usb resume
    ehci_hcd 0000:00:1d.7: resume root hub
    hub 2-0:1.0: hub_resume
    usb 2-1: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
    usb 2-1: finish resume
    usb 2-7: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
    usb 2-7: finish resume
    sd 2:0:0:0: [sda] Starting disk
    usb usb1: suspend_rh (auto-stop)
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: configured for UDMA/100
    sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    usb usb3: usb resume
    usb usb3: wakeup_rh
    hub 3-0:1.0: hub_resume
    usb usb4: usb resume
    usb usb4: wakeup_rh
    hub 4-0:1.0: hub_resume
    usb usb5: usb resume
    usb usb5: wakeup_rh
    hub 5-0:1.0: hub_resume
    usb 2-6: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: finish resume
    Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
    done.
    hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
    usb usb3: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    usb usb5: suspend_rh (auto-stop)
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    usb usb1: suspend_rh
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 5-0:1.0: hub_suspend
    usb usb5: bus auto-suspend
    usb usb5: suspend_rh
    Stopping tasks ... done.
    Suspending console(s)
    usb 2-6: usb suspend
    sd 2:0:0:0: [sda] Synchronizing SCSI cache
    sd 2:0:0:0: [sda] Stopping disk
    usb 2-7: usb suspend
    usb 2-1: usb suspend
    hub 2-0:1.0: hub_suspend
    usb usb2: bus suspend
    ehci_hcd 0000:00:1d.7: suspend root hub
    ACPI handle has no context!
    ACPI handle has no context!
    ACPI: PCI interrupt for device 0000:00:1f.2 disabled
    ACPI: PCI interrupt for device 0000:00:1f.1 disabled
    ACPI: PCI interrupt for device 0000:00:1d.7 disabled
    ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
    uhci_hcd 0000:00:1d.3: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.3 disabled
    uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.2: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.2 disabled
    uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.1: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.1 disabled
    uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.0: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.0 disabled
    uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
    ACPI: PCI interrupt for device 0000:00:1b.0 disabled
    Disabling non-boot CPUs ...
    CPU 1 is now offline
    SMP alternatives: switching to UP code
    CPU1 is down
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU0: Thermal monitoring enabled
    Back to C!
    Enabling non-boot CPUs ...
    SMP alternatives: switching to SMP code
    Booting processor 1/1 eip 3000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 6004.38 BogoMIPS (lpj=10003811)
    CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
    monitor/mwait feature present.
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU1: Thermal monitoring enabled
    CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
    CPU1 is up
    ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
    Switched to high resolution mode on CPU 1
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
    PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
    PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
    PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
    PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    uhci_hcd 0000:00:1d.0: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: uhci_resume
    uhci_hcd 0000:00:1d.1: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: uhci_resume
    uhci_hcd 0000:00:1d.2: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: uhci_resume
    uhci_hcd 0000:00:1d.3: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: uhci_resume
    ehci_hcd 0000:00:1d.7: resume from PCI D3
    PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
    PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1f.1 to 64
    ata2: port disabled. ignoring.
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    pnp: Failed to activate device 00:07.
    pnp: Failed to activate device 00:08.
    e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
    ata4: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    ata5: SATA link down (SStatus 0 SControl 300)
    ata1.00: configured for UDMA/33
    usb usb1: usb resume
    usb usb1: wakeup_rh
    hub 1-0:1.0: hub_resume
    usb usb2: usb resume
    ehci_hcd 0000:00:1d.7: resume root hub
    hub 2-0:1.0: hub_resume
    usb 2-1: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
    usb 2-1: finish resume
    usb 2-7: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
    usb 2-7: finish resume
    sd 2:0:0:0: [sda] Starting disk
    usb usb1: suspend_rh (auto-stop)
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: configured for UDMA/100
    sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    usb usb3: usb resume
    usb usb3: wakeup_rh
    hub 3-0:1.0: hub_resume
    usb usb4: usb resume
    usb usb4: wakeup_rh
    hub 4-0:1.0: hub_resume
    usb usb5: usb resume
    usb usb5: wakeup_rh
    hub 5-0:1.0: hub_resume
    usb 2-6: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: finish resume
    Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
    done.
    usb usb3: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    usb usb5: suspend_rh (auto-stop)
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    usb usb1: suspend_rh
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 5-0:1.0: hub_suspend
    usb usb5: bus auto-suspend
    usb usb5: suspend_rh
    Stopping tasks ... done.
    Suspending console(s)
    usb 2-6: usb suspend
    sd 2:0:0:0: [sda] Synchronizing SCSI cache
    sd 2:0:0:0: [sda] Stopping disk
    usb 2-7: usb suspend
    usb 2-1: usb suspend
    hub 2-0:1.0: hub_suspend
    usb usb2: bus suspend
    ehci_hcd 0000:00:1d.7: suspend root hub
    ACPI handle has no context!
    ACPI handle has no context!
    ACPI: PCI interrupt for device 0000:00:1f.2 disabled
    ACPI: PCI interrupt for device 0000:00:1f.1 disabled
    ACPI: PCI interrupt for device 0000:00:1d.7 disabled
    ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
    uhci_hcd 0000:00:1d.3: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.3 disabled
    uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.2: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.2 disabled
    uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.1: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.1 disabled
    uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.0: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.0 disabled
    uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
    ACPI: PCI interrupt for device 0000:00:1b.0 disabled
    Disabling non-boot CPUs ...
    CPU 1 is now offline
    SMP alternatives: switching to UP code
    CPU1 is down
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU0: Thermal monitoring enabled
    Back to C!
    Enabling non-boot CPUs ...
    SMP alternatives: switching to SMP code
    Booting processor 1/1 eip 3000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 6004.35 BogoMIPS (lpj=10003766)
    CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
    monitor/mwait feature present.
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU1: Thermal monitoring enabled
    CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
    CPU1 is up
    ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
    Switched to high resolution mode on CPU 1
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
    PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
    PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
    PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
    PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    uhci_hcd 0000:00:1d.0: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: uhci_resume
    uhci_hcd 0000:00:1d.1: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: uhci_resume
    uhci_hcd 0000:00:1d.2: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: uhci_resume
    uhci_hcd 0000:00:1d.3: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: uhci_resume
    ehci_hcd 0000:00:1d.7: resume from PCI D3
    PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
    PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1f.1 to 64
    ata2: port disabled. ignoring.
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    pnp: Failed to activate device 00:07.
    pnp: Failed to activate device 00:08.
    e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
    ata5: SATA link down (SStatus 0 SControl 300)
    ata4: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    ata1.00: configured for UDMA/33
    usb usb1: usb resume
    usb usb1: wakeup_rh
    hub 1-0:1.0: hub_resume
    usb usb2: usb resume
    ehci_hcd 0000:00:1d.7: resume root hub
    hub 2-0:1.0: hub_resume
    usb 2-1: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
    usb 2-1: finish resume
    usb 2-7: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
    usb 2-7: finish resume
    sd 2:0:0:0: [sda] Starting disk
    usb usb1: suspend_rh (auto-stop)
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: configured for UDMA/100
    sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    usb usb3: usb resume
    usb usb3: wakeup_rh
    hub 3-0:1.0: hub_resume
    usb usb4: usb resume
    usb usb4: wakeup_rh
    hub 4-0:1.0: hub_resume
    usb usb5: usb resume
    usb usb5: wakeup_rh
    hub 5-0:1.0: hub_resume
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
    hub 2-0:1.0: port 6 status 0001.0501 after resume, 0
    usb 2-6: can't resume, status -19
    hub 2-0:1.0: logical disconnect on port 6
    Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
    done.
    hub 2-0:1.0: state 7 ports 8 chg 0040 evt 0000
    hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
    usb 2-6: USB disconnect, address 8
    usb 2-6: unregistering device
    usb 2-6: usb_disable_device nuking all URBs
    usb 2-6: unregistering interface 2-6:1.0
    usb_endpoint usbdev2.8_ep81: ep_device_release called for usbdev2.8_ep81
    usb_endpoint usbdev2.8_ep02: ep_device_release called for usbdev2.8_ep02
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: [sdb] READ CAPACITY failed
    scsi 12:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00
    scsi 12:0:0:0: [sdb] Sense not available.
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: [sdb] Write Protect is off
    scsi 12:0:0:0: [sdb] Mode Sense: 00 00 00 00
    scsi 12:0:0:0: [sdb] Assuming drive cache: write through
    usb 2-6:1.0: uevent
    usb 2-6:1.0: uevent
    usb_endpoint usbdev2.8_ep00: ep_device_release called for usbdev2.8_ep00
    usb 2-6: uevent
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11838) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11839) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11840) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11841) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11842) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11843) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11844) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11845) failed
    ehci_hcd 0000:00:1d.7: port 6 high speed
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: new high speed USB device using ehci_hcd and address 9
    ehci_hcd 0000:00:1d.7: port 6 high speed
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: default language 0x0409
    usb 2-6: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 2-6: Product: Flash Disk
    usb 2-6: Manufacturer: USB 2.0
    usb 2-6: SerialNumber: AA04012700008519
    usb 2-6: uevent
    usb 2-6: usb_probe_device
    usb 2-6: configuration #1 chosen from 1 choice
    usb 2-6: adding 2-6:1.0 (config #1, interface 0)
    usb 2-6:1.0: uevent
    usb 2-6:1.0: uevent
    usb-storage 2-6:1.0: usb_probe_interface
    usb-storage 2-6:1.0: usb_probe_interface - got id
    scsi13 : SCSI emulation for USB Mass Storage devices
    drivers/usb/core/inode.c: creating file '009'
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
    usb-storage: device found at 9
    usb-storage: waiting for device to settle before scanning
    usb usb3: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    usb usb5: suspend_rh (auto-stop)
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    usb usb1: suspend_rh
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 5-0:1.0: hub_suspend
    usb usb5: bus auto-suspend
    usb usb5: suspend_rh
    scsi 13:0:0:0: Direct-Access USB 2.0 Flash Disk 1100 PQ: 0 ANSI: 0 CCS
    sd 13:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
    sd 13:0:0:0: [sdb] Write Protect is off
    sd 13:0:0:0: [sdb] Mode Sense: 43 00 00 00
    sd 13:0:0:0: [sdb] Assuming drive cache: write through
    sd 13:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
    sd 13:0:0:0: [sdb] Write Protect is off
    sd 13:0:0:0: [sdb] Mode Sense: 43 00 00 00
    sd 13:0:0:0: [sdb] Assuming drive cache: write through
    sdb: sdb1 sdb2
    sd 13:0:0:0: [sdb] Attached SCSI removable disk
    sd 13:0:0:0: Attached scsi generic sg3 type 0
    usb-storage: device scan complete
    Stopping tasks ... done.
    Suspending console(s)
    usb 2-6: usb suspend
    sd 2:0:0:0: [sda] Synchronizing SCSI cache
    sd 2:0:0:0: [sda] Stopping disk
    usb 2-7: usb suspend
    usb 2-1: usb suspend
    hub 2-0:1.0: hub_suspend
    usb usb2: bus suspend
    ehci_hcd 0000:00:1d.7: suspend root hub
    ACPI handle has no context!
    ACPI handle has no context!
    ACPI: PCI interrupt for device 0000:00:1f.2 disabled
    ACPI: PCI interrupt for device 0000:00:1f.1 disabled
    ACPI: PCI interrupt for device 0000:00:1d.7 disabled
    ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
    uhci_hcd 0000:00:1d.3: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.3 disabled
    uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.2: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.2 disabled
    uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.1: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.1 disabled
    uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.0: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.0 disabled
    uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
    ACPI: PCI interrupt for device 0000:00:1b.0 disabled
    Disabling non-boot CPUs ...
    CPU 1 is now offline
    SMP alternatives: switching to UP code
    CPU1 is down
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU0: Thermal monitoring enabled
    Back to C!
    Enabling non-boot CPUs ...
    SMP alternatives: switching to SMP code
    Booting processor 1/1 eip 3000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 6004.34 BogoMIPS (lpj=10003759)
    CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
    monitor/mwait feature present.
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU1: Thermal monitoring enabled
    CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
    CPU1 is up
    ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
    Switched to high resolution mode on CPU 1
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
    PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
    PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
    PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
    PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    uhci_hcd 0000:00:1d.0: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: uhci_resume
    uhci_hcd 0000:00:1d.1: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: uhci_resume
    uhci_hcd 0000:00:1d.2: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: uhci_resume
    uhci_hcd 0000:00:1d.3: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: uhci_resume
    ehci_hcd 0000:00:1d.7: resume from PCI D3
    PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
    PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1f.1 to 64
    ata2: port disabled. ignoring.
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    pnp: Failed to activate device 00:07.
    pnp: Failed to activate device 00:08.
    e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
    ata4: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    ata5: SATA link down (SStatus 0 SControl 300)
    ata1.00: configured for UDMA/33
    usb usb1: usb resume
    usb usb1: wakeup_rh
    hub 1-0:1.0: hub_resume
    usb usb2: usb resume
    ehci_hcd 0000:00:1d.7: resume root hub
    hub 2-0:1.0: hub_resume
    usb 2-1: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
    usb 2-1: finish resume
    usb 2-7: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
    usb 2-7: finish resume
    sd 2:0:0:0: [sda] Starting disk
    usb usb1: suspend_rh (auto-stop)
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: configured for UDMA/100
    sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    usb usb3: usb resume
    usb usb3: wakeup_rh
    hub 3-0:1.0: hub_resume
    usb usb4: usb resume
    usb usb4: wakeup_rh
    hub 4-0:1.0: hub_resume
    usb usb5: usb resume
    usb usb5: wakeup_rh
    hub 5-0:1.0: hub_resume
    usb 2-6: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: finish resume
    Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
    done.
    usb usb3: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    usb usb5: suspend_rh (auto-stop)
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    usb usb1: suspend_rh
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 5-0:1.0: hub_suspend
    usb usb5: bus auto-suspend
    usb usb5: suspend_rh
    PI: Unable to turn cooling device [dfe0cdc8] 'off'
    Switched to high resolution mode on CPU 1
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
    PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
    PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
    PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
    PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    uhci_hcd 0000:00:1d.0: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: uhci_resume
    uhci_hcd 0000:00:1d.1: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: uhci_resume
    uhci_hcd 0000:00:1d.2: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: uhci_resume
    uhci_hcd 0000:00:1d.3: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: uhci_resume
    ehci_hcd 0000:00:1d.7: resume from PCI D3
    PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
    PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1f.1 to 64
    ata2: port disabled. ignoring.
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    pnp: Failed to activate device 00:07.
    pnp: Failed to activate device 00:08.
    e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
    ata4: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    ata5: SATA link down (SStatus 0 SControl 300)
    ata1.00: configured for UDMA/33
    usb usb1: usb resume
    usb usb1: wakeup_rh
    hub 1-0:1.0: hub_resume
    usb usb2: usb resume
    ehci_hcd 0000:00:1d.7: resume root hub
    hub 2-0:1.0: hub_resume
    usb 2-1: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
    usb 2-1: finish resume
    usb 2-7: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
    usb 2-7: finish resume
    sd 2:0:0:0: [sda] Starting disk
    usb usb1: suspend_rh (auto-stop)
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: configured for UDMA/100
    sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    usb usb3: usb resume
    usb usb3: wakeup_rh
    hub 3-0:1.0: hub_resume
    usb usb4: usb resume
    usb usb4: wakeup_rh
    hub 4-0:1.0: hub_resume
    usb usb5: usb resume
    usb usb5: wakeup_rh
    hub 5-0:1.0: hub_resume
    usb 2-6: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: finish resume
    Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
    done.
    usb usb3: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    usb usb5: suspend_rh (auto-stop)
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    usb usb1: suspend_rh
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 5-0:1.0: hub_suspend
    usb usb5: bus auto-suspend
    usb usb5: suspend_rh
    Stopping tasks ... done.
    Suspending console(s)
    usb 2-6: usb suspend
    sd 2:0:0:0: [sda] Synchronizing SCSI cache
    sd 2:0:0:0: [sda] Stopping disk
    usb 2-7: usb suspend
    usb 2-1: usb suspend
    hub 2-0:1.0: hub_suspend
    usb usb2: bus suspend
    ehci_hcd 0000:00:1d.7: suspend root hub
    ACPI handle has no context!
    ACPI handle has no context!
    ACPI: PCI interrupt for device 0000:00:1f.2 disabled
    ACPI: PCI interrupt for device 0000:00:1f.1 disabled
    ACPI: PCI interrupt for device 0000:00:1d.7 disabled
    ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
    uhci_hcd 0000:00:1d.3: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.3 disabled
    uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.2: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.2 disabled
    uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.1: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.1 disabled
    uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.0: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.0 disabled
    uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
    ACPI: PCI interrupt for device 0000:00:1b.0 disabled
    Disabling non-boot CPUs ...
    CPU 1 is now offline
    SMP alternatives: switching to UP code
    CPU1 is down
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU0: Thermal monitoring enabled
    Back to C!
    Enabling non-boot CPUs ...
    SMP alternatives: switching to SMP code
    Booting processor 1/1 eip 3000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 6004.35 BogoMIPS (lpj=10003766)
    CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
    monitor/mwait feature present.
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU1: Thermal monitoring enabled
    CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
    CPU1 is up
    ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
    Switched to high resolution mode on CPU 1
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
    PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
    PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
    PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
    PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    uhci_hcd 0000:00:1d.0: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: uhci_resume
    uhci_hcd 0000:00:1d.1: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: uhci_resume
    uhci_hcd 0000:00:1d.2: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: uhci_resume
    uhci_hcd 0000:00:1d.3: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: uhci_resume
    ehci_hcd 0000:00:1d.7: resume from PCI D3
    PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
    PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1f.1 to 64
    ata2: port disabled. ignoring.
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    pnp: Failed to activate device 00:07.
    pnp: Failed to activate device 00:08.
    e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
    ata5: SATA link down (SStatus 0 SControl 300)
    ata4: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    ata1.00: configured for UDMA/33
    usb usb1: usb resume
    usb usb1: wakeup_rh
    hub 1-0:1.0: hub_resume
    usb usb2: usb resume
    ehci_hcd 0000:00:1d.7: resume root hub
    hub 2-0:1.0: hub_resume
    usb 2-1: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
    usb 2-1: finish resume
    usb 2-7: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
    usb 2-7: finish resume
    sd 2:0:0:0: [sda] Starting disk
    usb usb1: suspend_rh (auto-stop)
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: configured for UDMA/100
    sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    usb usb3: usb resume
    usb usb3: wakeup_rh
    hub 3-0:1.0: hub_resume
    usb usb4: usb resume
    usb usb4: wakeup_rh
    hub 4-0:1.0: hub_resume
    usb usb5: usb resume
    usb usb5: wakeup_rh
    hub 5-0:1.0: hub_resume
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
    hub 2-0:1.0: port 6 status 0001.0501 after resume, 0
    usb 2-6: can't resume, status -19
    hub 2-0:1.0: logical disconnect on port 6
    Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
    done.
    hub 2-0:1.0: state 7 ports 8 chg 0040 evt 0000
    hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
    usb 2-6: USB disconnect, address 8
    usb 2-6: unregistering device
    usb 2-6: usb_disable_device nuking all URBs
    usb 2-6: unregistering interface 2-6:1.0
    usb_endpoint usbdev2.8_ep81: ep_device_release called for usbdev2.8_ep81
    usb_endpoint usbdev2.8_ep02: ep_device_release called for usbdev2.8_ep02
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: [sdb] READ CAPACITY failed
    scsi 12:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00
    scsi 12:0:0:0: [sdb] Sense not available.
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: [sdb] Write Protect is off
    scsi 12:0:0:0: [sdb] Mode Sense: 00 00 00 00
    scsi 12:0:0:0: [sdb] Assuming drive cache: write through
    usb 2-6:1.0: uevent
    usb 2-6:1.0: uevent
    usb_endpoint usbdev2.8_ep00: ep_device_release called for usbdev2.8_ep00
    usb 2-6: uevent
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11838) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11839) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11840) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11841) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11842) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11843) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11844) failed
    scsi 12:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11845) failed
    ehci_hcd 0000:00:1d.7: port 6 high speed
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: new high speed USB device using ehci_hcd and address 9
    ehci_hcd 0000:00:1d.7: port 6 high speed
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: default language 0x0409
    usb 2-6: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 2-6: Product: Flash Disk
    usb 2-6: Manufacturer: USB 2.0
    usb 2-6: SerialNumber: AA04012700008519
    usb 2-6: uevent
    usb 2-6: usb_probe_device
    usb 2-6: configuration #1 chosen from 1 choice
    usb 2-6: adding 2-6:1.0 (config #1, interface 0)
    usb 2-6:1.0: uevent
    usb 2-6:1.0: uevent
    usb-storage 2-6:1.0: usb_probe_interface
    usb-storage 2-6:1.0: usb_probe_interface - got id
    scsi13 : SCSI emulation for USB Mass Storage devices
    drivers/usb/core/inode.c: creating file '009'
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
    usb-storage: device found at 9
    usb-storage: waiting for device to settle before scanning
    usb usb3: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    usb usb5: suspend_rh (auto-stop)
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    usb usb1: suspend_rh
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 5-0:1.0: hub_suspend
    usb usb5: bus auto-suspend
    usb usb5: suspend_rh
    scsi 13:0:0:0: Direct-Access USB 2.0 Flash Disk 1100 PQ: 0 ANSI: 0 CCS
    sd 13:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
    sd 13:0:0:0: [sdb] Write Protect is off
    sd 13:0:0:0: [sdb] Mode Sense: 43 00 00 00
    sd 13:0:0:0: [sdb] Assuming drive cache: write through
    sd 13:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
    sd 13:0:0:0: [sdb] Write Protect is off
    sd 13:0:0:0: [sdb] Mode Sense: 43 00 00 00
    sd 13:0:0:0: [sdb] Assuming drive cache: write through
    sdb: sdb1 sdb2
    sd 13:0:0:0: [sdb] Attached SCSI removable disk
    sd 13:0:0:0: Attached scsi generic sg3 type 0
    usb-storage: device scan complete
    Stopping tasks ... done.
    Suspending console(s)
    usb 2-6: usb suspend
    sd 2:0:0:0: [sda] Synchronizing SCSI cache
    sd 2:0:0:0: [sda] Stopping disk
    usb 2-7: usb suspend
    usb 2-1: usb suspend
    hub 2-0:1.0: hub_suspend
    usb usb2: bus suspend
    ehci_hcd 0000:00:1d.7: suspend root hub
    ACPI handle has no context!
    ACPI handle has no context!
    ACPI: PCI interrupt for device 0000:00:1f.2 disabled
    ACPI: PCI interrupt for device 0000:00:1f.1 disabled
    ACPI: PCI interrupt for device 0000:00:1d.7 disabled
    ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
    uhci_hcd 0000:00:1d.3: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.3 disabled
    uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.2: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.2 disabled
    uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.1: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.1 disabled
    uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.0: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.0 disabled
    uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
    ACPI: PCI interrupt for device 0000:00:1b.0 disabled
    Disabling non-boot CPUs ...
    CPU 1 is now offline
    SMP alternatives: switching to UP code
    CPU1 is down
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU0: Thermal monitoring enabled
    Back to C!
    Enabling non-boot CPUs ...
    SMP alternatives: switching to SMP code
    Booting processor 1/1 eip 3000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 6004.34 BogoMIPS (lpj=10003759)
    CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
    monitor/mwait feature present.
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU1: Thermal monitoring enabled
    CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
    CPU1 is up
    ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
    Switched to high resolution mode on CPU 1
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
    PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
    PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
    PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
    PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    uhci_hcd 0000:00:1d.0: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: uhci_resume
    uhci_hcd 0000:00:1d.1: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: uhci_resume
    uhci_hcd 0000:00:1d.2: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: uhci_resume
    uhci_hcd 0000:00:1d.3: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: uhci_resume
    ehci_hcd 0000:00:1d.7: resume from PCI D3
    PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
    PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1f.1 to 64
    ata2: port disabled. ignoring.
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    pnp: Failed to activate device 00:07.
    pnp: Failed to activate device 00:08.
    e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
    ata4: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    ata5: SATA link down (SStatus 0 SControl 300)
    ata1.00: configured for UDMA/33
    usb usb1: usb resume
    usb usb1: wakeup_rh
    hub 1-0:1.0: hub_resume
    usb usb2: usb resume
    ehci_hcd 0000:00:1d.7: resume root hub
    hub 2-0:1.0: hub_resume
    usb 2-1: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
    usb 2-1: finish resume
    usb 2-7: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
    usb 2-7: finish resume
    sd 2:0:0:0: [sda] Starting disk
    usb usb1: suspend_rh (auto-stop)
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: configured for UDMA/100
    sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    usb usb3: usb resume
    usb usb3: wakeup_rh
    hub 3-0:1.0: hub_resume
    usb usb4: usb resume
    usb usb4: wakeup_rh
    hub 4-0:1.0: hub_resume
    usb usb5: usb resume
    usb usb5: wakeup_rh
    hub 5-0:1.0: hub_resume
    usb 2-6: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: finish resume
    Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
    done.
    usb usb3: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    usb usb5: suspend_rh (auto-stop)
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    usb usb1: suspend_rh
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 5-0:1.0: hub_suspend
    usb usb5: bus auto-suspend
    usb usb5: suspend_rh
    Stopping tasks ... done.
    Suspending console(s)
    usb 2-6: usb suspend
    sd 2:0:0:0: [sda] Synchronizing SCSI cache
    sd 2:0:0:0: [sda] Stopping disk
    usb 2-7: usb suspend
    usb 2-1: usb suspend
    hub 2-0:1.0: hub_suspend
    usb usb2: bus suspend
    ehci_hcd 0000:00:1d.7: suspend root hub
    ACPI handle has no context!
    ACPI handle has no context!
    ACPI: PCI interrupt for device 0000:00:1f.2 disabled
    ACPI: PCI interrupt for device 0000:00:1f.1 disabled
    ACPI: PCI interrupt for device 0000:00:1d.7 disabled
    ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
    uhci_hcd 0000:00:1d.3: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.3 disabled
    uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.2: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.2 disabled
    uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.1: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.1 disabled
    uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
    uhci_hcd 0000:00:1d.0: uhci_suspend
    ACPI: PCI interrupt for device 0000:00:1d.0 disabled
    uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
    ACPI: PCI interrupt for device 0000:00:1b.0 disabled
    Disabling non-boot CPUs ...
    CPU 1 is now offline
    SMP alternatives: switching to UP code
    CPU1 is down
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU0: Thermal monitoring enabled
    Back to C!
    Enabling non-boot CPUs ...
    SMP alternatives: switching to SMP code
    Booting processor 1/1 eip 3000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 6004.36 BogoMIPS (lpj=10003778)
    CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
    monitor/mwait feature present.
    CPU: Trace cache: 12K uops, L1 D cache: 16K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
    CPU1: Thermal monitoring enabled
    CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
    CPU1 is up
    ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
    Switched to high resolution mode on CPU 1
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
    PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
    PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
    PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
    PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    uhci_hcd 0000:00:1d.0: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: uhci_resume
    uhci_hcd 0000:00:1d.1: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: uhci_resume
    uhci_hcd 0000:00:1d.2: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: uhci_resume
    uhci_hcd 0000:00:1d.3: PCI legacy resume
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: uhci_resume
    ehci_hcd 0000:00:1d.7: resume from PCI D3
    PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
    PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1f.1 to 64
    ata2: port disabled. ignoring.
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    pnp: Failed to activate device 00:07.
    pnp: Failed to activate device 00:08.
    e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
    ata5: SATA link down (SStatus 0 SControl 300)
    ata4: SATA link down (SStatus 0 SControl 300)
    ata6: SATA link down (SStatus 0 SControl 300)
    ata1.00: configured for UDMA/33
    usb usb1: usb resume
    usb usb1: wakeup_rh
    hub 1-0:1.0: hub_resume
    usb usb2: usb resume
    ehci_hcd 0000:00:1d.7: resume root hub
    hub 2-0:1.0: hub_resume
    usb 2-1: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
    usb 2-1: finish resume
    usb 2-7: usb resume
    ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
    usb 2-7: finish resume
    sd 2:0:0:0: [sda] Starting disk
    usb usb1: suspend_rh (auto-stop)
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: configured for UDMA/100
    sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    usb usb3: usb resume
    usb usb3: wakeup_rh
    hub 3-0:1.0: hub_resume
    usb usb4: usb resume
    usb usb4: wakeup_rh
    hub 4-0:1.0: hub_resume
    usb usb5: usb resume
    usb usb5: wakeup_rh
    hub 5-0:1.0: hub_resume
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
    hub 2-0:1.0: port 6 status 0001.0501 after resume, 0
    usb 2-6: can't resume, status -19
    hub 2-0:1.0: logical disconnect on port 6
    Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
    done.
    hub 2-0:1.0: state 7 ports 8 chg 0040 evt 0000
    hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
    usb 2-6: USB disconnect, address 9
    usb 2-6: unregistering device
    usb 2-6: usb_disable_device nuking all URBs
    usb 2-6: unregistering interface 2-6:1.0
    usb_endpoint usbdev2.9_ep81: ep_device_release called for usbdev2.9_ep81
    usb_endpoint usbdev2.9_ep02: ep_device_release called for usbdev2.9_ep02
    sd 13:0:0:0: [sdb] READ CAPACITY failed
    sd 13:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00
    scsi 13:0:0:0: [sdb] Sense not available.
    scsi 13:0:0:0: [sdb] Write Protect is off
    scsi 13:0:0:0: [sdb] Mode Sense: 00 00 00 00
    scsi 13:0:0:0: [sdb] Assuming drive cache: write through
    usb 2-6:1.0: uevent
    usb 2-6:1.0: uevent
    usb_endpoint usbdev2.9_ep00: ep_device_release called for usbdev2.9_ep00
    usb 2-6: uevent
    scsi 13:0:0:0: rejecting I/O to dead device
    scsi 13:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11838) failed
    scsi 13:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11839) failed
    scsi 13:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11840) failed
    scsi 13:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11841) failed
    scsi 13:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11842) failed
    scsi 13:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11843) failed
    scsi 13:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11844) failed
    scsi 13:0:0:0: rejecting I/O to dead device
    FAT: Directory bread(block 11845) failed
    ehci_hcd 0000:00:1d.7: port 6 high speed
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: new high speed USB device using ehci_hcd and address 10
    ehci_hcd 0000:00:1d.7: port 6 high speed
    ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
    usb 2-6: default language 0x0409
    usb 2-6: new device strings: Mfr=1, Product=2, SerialNumber=3
    usb 2-6: Product: Flash Disk
    usb 2-6: Manufacturer: USB 2.0
    usb 2-6: SerialNumber: AA04012700008519
    usb 2-6: uevent
    usb 2-6: usb_probe_device
    usb 2-6: configuration #1 chosen from 1 choice
    usb 2-6: adding 2-6:1.0 (config #1, interface 0)
    usb 2-6:1.0: uevent
    usb 2-6:1.0: uevent
    usb-storage 2-6:1.0: usb_probe_interface
    usb-storage 2-6:1.0: usb_probe_interface - got id
    scsi14 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 10
    usb-storage: waiting for device to settle before scanning
    drivers/usb/core/inode.c: creating file '010'
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
    usb usb3: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    usb usb5: suspend_rh (auto-stop)
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    usb usb1: suspend_rh
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 5-0:1.0: hub_suspend
    usb usb5: bus auto-suspend
    usb usb5: suspend_rh
    scsi 14:0:0:0: Direct-Access USB 2.0 Flash Disk 1100 PQ: 0 ANSI: 0 CCS
    sd 14:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
    sd 14:0:0:0: [sdb] Write Protect is off
    sd 14:0:0:0: [sdb] Mode Sense: 43 00 00 00
    sd 14:0:0:0: [sdb] Assuming drive cache: write through
    sd 14:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
    sd 14:0:0:0: [sdb] Write Protect is off
    sd 14:0:0:0: [sdb] Mode Sense: 43 00 00 00
    sd 14:0:0:0: [sdb] Assuming drive cache: write through
    sdb: sdb1 sdb2
    sd 14:0:0:0: [sdb] Attached SCSI removable disk
    sd 14:0:0:0: Attached scsi generic sg3 type 0
    usb-storage: device scan complete
    \
     
     \ /
      Last update: 2007-11-28 07:05    [W:0.122 / U:29.740 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site