Messages in this thread | | | Date | Mon, 19 Nov 2007 23:15:54 +0100 | From | Sam Ravnborg <> | Subject | Re: [RFC] x86: document kernel config and build |
| |
On Mon, Nov 19, 2007 at 06:33:20PM +0100, Andreas Herrmann wrote: > Hi, > > I suggest to add some documentation snippet to > > Documentation/x86/{kbuild,kconfig,README} > > or whatsoever to primarily describe the new ARCH=x86 build. > As a starter I named it Documentation/x86/kbuild.
I would prefer a general document that has a target specific section.
Something like Documentation/make/headers_install and your text merged. And the resuting file could be named kernel-build-howto.txt (or similar) and located in Documentation/kbuild/
On top of this we should enhance the arch specific help for x86 to tell how to select bit-size. But I have left that until we unify the 32 and 64 bit Makefiles.
I have yet to read your document - too late for that now..
Sam
> > The following text is based on my observations with > Linus' git (v2.6.24-rc3-19-g2ffbb83). > Some text was shamelessly stolen from one of Sam's patch > descriptions. > > Comments are welcome. > > > Regards, > > Andreas > > -- > Added documentation about kernel configuration and build for ARCH=x86. > > Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> > --- > arch/x86/kbuild | 71 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ > 1 files changed, 71 insertions(+), 0 deletions(-) > create mode 100644 arch/x86/kbuild > > diff --git a/arch/x86/kbuild b/arch/x86/kbuild > new file mode 100644 > index 0000000..7a918a9 > --- /dev/null > +++ b/arch/x86/kbuild > @@ -0,0 +1,71 @@ > +Kernel configuration > + > + The general rule is that ARCH={i386,x86_64} and native > + architecture take precedence over the configuration. > + So make ARCH=i386 [whatever] will always build a 32-bit > + kernel no matter what the configuration says. > + The configuration will be updated to 32-bit if it was > + configured to 64-bit and the other way around: > + > + /=================================================\ > + | Target kernel architecture for | > + | $ make [ARCH=...] <config-target> | > + |-------------------------------------------------| > + | option \ host arch | i386 | x86_64 | > + |=================================================| > + | ./. | i386 | x86_64 | > + | ARCH=i386 | i386 | i386 | > + | ARCH=x86_64 | x86_64 | x86_64 | > + \=================================================/ > + > + This behaviour is consistent with previous behaviour so > + no surprises here. > + > + "make ARCH=x86" is special. It is the only ARCH= value that > + allows the user to select between 32-bit and 64-bit using > + menuconfig. This has impact on most config targets. Following > + table shows what kernel will be configured depending on host > + architecture and config-target. > + > + /=========================================================\ > + | Target kernel architecture for | > + | $ make ARCH=x86 <config-target> | > + |---------------------------------------------------------| > + | config-target \ host arch | i386 | x86_64 | > + |=========================================================| > + | [menu]config (*1) | i386/x86_64 | i386/x86_64 | > + | {old,silentold}config (*2) | i386/x86_64 | i386/x86_64 | > + | defconfig | i386 | i386 | > + | randconfig (*3) | i386/x86_64 | i386/x86_64 | > + | allnoconfig | i386 | i386 | > + | allyesconfig | x86_64 | x86_64 | > + | allmodconfig | x86_64 | x86_64 | > + |---------------------------------------------------------| > + | (*1) The default selection equals the host architecture | > + | for new configurations. Otherwise it depends on the | > + | setting of CONFIG_64BIT in the old configuration. | > + |---------------------------------------------------------| > + | (*2) The default selection depends on the setting of | > + | CONFIG_64BIT in the old configuration. | > + |---------------------------------------------------------| > + | (*3) Both configurations are possible. | > + \=========================================================/ > + > + > +Cross compilation > + > + (1) To compile a 32-bit kernel on a x86_64 system you have to > + disable 64-bit support in the kernel configuration > + (CONFIG_64BIT=n). > + > + A subsequent kernel compile will build a 32-bit kernel. No > + cross compiler is needed. > + > + (2) To compile a 64-bit kernel on a i386 system you have to switch > + on 64-bit support in the kernel configuration (CONFIG_64BIT=y). > + In the subsequent kernel compile a cross compiler (supporting > + x86_64) is needed. You have to use a command line like > + > + $ make CROSS_COMPILE=x86_64-pc-linux-gnu- > + > + to cross compile your kernel. > -- > 1.5.3.4 > > > > - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |